SANS 53763-15-2008 Explosives for civil uses - Detonators and relays Part 15 Determination of equivalent initiating capability《民用爆炸品 雷管及导爆替续器 第15部分 启爆当量能力测定》.pdf

《SANS 53763-15-2008 Explosives for civil uses - Detonators and relays Part 15 Determination of equivalent initiating capability《民用爆炸品 雷管及导爆替续器 第15部分 启爆当量能力测定》.pdf》由会员分享，可在线阅读，更多相关《SANS 53763-15-2008 Explosives for civil uses - Detonators and relays Part 15 Determination of equivalent initiating capability《民用爆炸品 雷管及导爆替续器 第15部分 启爆当量能力测定》.pdf（23页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21729-7 SANS 53763-15:2008Edition 1EN 13763-15:2004Edition 1SOUTH AFRICAN NATIONAL STANDARD Explosives for civil uses Detonators and relay

4、s Part 15: Determination of equivalent initiating capability This national standard is the identical implementation of EN 13763-15:2004 and is adopted with the permission of the CEN, rue de Stassart 36, B-1050 Brussels. Published by Standards South Africa 1 dr lategan road groenkloof private bag x19

5、1 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 53763-15:2008 Edition 1 EN 13763-15:2004 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee StanS

6、A TC 5140.04, Explosives and detonators, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in August 2008. EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 13763-15October 2004ICS 71.100.30English versionExplosi

7、ves for civil uses - Detonators and relays - Part 15:Determination of equivalent initiating capabilityExplosifs usage civil - Dtonateurs et relais - Partie 15:Dtermination de la capacit damorage quivalenteExplosivstoffe fr zivile Zwecke - Znder undVerzgerungselemente - Teil 15: Bestimmung derZndstrk

8、eThis European Standard was approved by CEN on 9 January 2004.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical refer

9、ences concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into

10、its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxe

11、mbourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussels 2004 CEN All rights of explo

12、itation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 13763-15:2004: ESANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 2 Contents Page Foreword3 1 Scope 6 2 Normative

13、 references 6 3 Terms and definitions .6 4 Test pieces .6 5 Apparatus .6 6 Procedure .9 7 Test report 11 Annex A (normative) Specifications for reference detonators .12 Annex B (informative) Range of applicability of the test method.16 Annex C (informative) Examples of results from underwater testin

14、g17 Annex ZA (informative) Clauses of this European Standard addressing essential requirements or other provisions of EU Directives19 SANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 3 Foreword This docum

15、ent (EN 13763:2004) has been prepared by Technical Committee CEN /TC 321, “Explosives for civil uses“, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by Ap

16、ril 2005, and conflicting national standards shall be withdrawn at the latest by April 2005. This document has been prepared under a mandate given to CEN by the European Commission and the European Free Trade Association, and supports essential requirements of EU Directive 93/15. For relationship wi

17、th EU Directives, see informative Annex ZA, which is an integral part of this standard. This document is one of a series of standards on Explosives for civil uses Detonators and relays. Other parts of this series are: EN 13763-1 Part 1: Requirements EN 13763-2 Part 2: Determination of thermal stabil

18、ity EN 13763-3 Part 3: Determination of sensitiveness to impact EN 13763-4 Part 4: Determination of resistance to abrasion of leading wires and shock tubes EN 13763-5 Part 5: Determination of resistance to cutting damage of leading wires and shock tubes EN 13763-6 Part 6: Determination of resistance

19、 to cracking in low temperatures of leading wires EN 13763-7 Part 7: Determination of the mechanical strength of leading wires, shock tubes, connections, crimps and closures EN 13763-8 Part 8: Determination of resistance to vibration of plain detonators EN 13763-9 Part 9: Determination of resistance

20、 to bending of detonators EN 13763-11 Part 11: Determination of resistance to damage by dropping of detonators and relays EN 13763-12 Part 12: Determination of resistance to hydrostatic pressure EN 13763-13 Part 13: Determination of resistance of electric detonator to electrostatic discharge EN 1376

21、3-16 Part 16: Determination of delay accuracy EN 13763-17 Part 17: Determination of no-fire current of electric detonators EN 13763-18 Part 18: Determination of series firing current of electric detonators EN 13763-19 Part 19: Determination of firing impulse of electric detonators EN 13763-20 Part 2

22、0: Determination of total electrical resistance of electric detonators EN 13763-21 Part 21: Determination of flash-over voltage of electric detonators EN 13763-22 Part 22: Determination of capacitance, insulation resistance and insulation breakdown of leading wires SANS 53763-15:2008This s tandard m

23、ay only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 4 EN 13763-23 Part 23: Determination of the shock-wave velocity of shock tubes EN 13763-24 Part 24: Determination of the electrical non-conductivity of shock tubes EN 13763-25 Part 25: Dete

24、rmination of transfer capability of surface connectors, relays and coupling accessories EN 13763-26 Part 26: Definitions, methods and requirements for devices and accessories for reliable and safe function of detonators and relays CEN/TS 13763-27 Part 27: Definitions, methods and requirements for el

25、ectronic initiation system According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,

26、 Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom. SANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:200

27、4 (E) 5 Introduction General When fired, the explosive charge of detonators must provide a pulse of sufficient energy to initiate the explosive or a detonating cord/shock tube, with which they are intended to be used. In the test procedure described in this document, the output performance of a test

28、 piece is compared with a reference having known characteristics and mass of charge. This document describes two tests: an underwater initiating capability test and a functioning test at low and high temperatures. Underwater initiating capability This test is based on the principle that the detonati

29、on of an explosive charge under water generates a spherical shock-wave and a volume of gas, which expands and then collapses as the bubble rises through the water. The shock-wave and the volume of gas bear a finite relationship to the energy released. Thus, by measuring: the shock-wave pressure; and

30、 the time interval between the shock-wave pressure peak and the first collapse of the gas bubble, and calculating the parameters proportional to: equivalent shock energy; and equivalent bubble energy, the energy output of the test detonators can be compared with the energy output of the reference de

31、tonator to which the manufacturer claims equivalence. Functioning test at high and low temperatures This test checks that the energy output of the detonators does not vary when they are fired at high and low temperatures, by firing detonators in contact with aluminium witness plates at ambient, high

32、 and low temperatures and comparing the depths of indentations made in the plates. SANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .This page is intentionally left blankSANS 53763-15:2008This s tandard may only be used and pr

33、inted by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 6 1 Scope This document specifies a method of determining the equivalent initiating capability of detonators. This document also specifies a functioning test (after storage) at high and low temperatures. This do

34、cument is not applicable to surface connectors or detonating cord relays. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenc

35、ed document (including any amendments) applies. EN 573-3, Aluminium and aluminium alloys Chemical composition and form of wrought products - Part 3: Chemical composition EN 13857-1:2003, Explosives for civil uses Part 1: Terminology. EN ISO/IEC 17025, General requirements for the competence of testi

36、ng and calibration laboratories (ISO/IEC 17025:1999). 3 Terms and definitions For the purposes of this document, the terms and definitions given in EN 13857-1:2003 apply. 4 Test pieces 4.1 Underwater initiating capability test Select 20 detonators of each specific type, having the same construction

37、and shell material and having the same design, quantity and type of primary and secondary charge. 4.2 Functioning test at high and low temperatures Select 50 detonators from each specific type, having the same construction and shell material and having the same design, quantity and type of primary a

38、nd secondary charge. 5 Apparatus 5.1 Underwater initiating capability test 5.1.1 Blasting tank (Water tank or outdoor facility), with a volume of at least 500 l, and constructed in such a way that shock-wave reflections from the walls are avoided, for example, in the case of a small tank (as shown i

39、n Figure 1), by lining the walls with plastics foam. 5.1.2 Positioning system, for the pressure sensor and detonator. The distance between the centre of the sensor and the detonator shall be (400 + 5) mm. The bottom of the detonator and sensor shall be placed (400 + 5) mm below the water surface. Th

40、e distance between any wall and the detonator shall be at least 200 mm. 5.1.3 Pressure sensor, with a rise time 0,5 % by mass and 1,0 % by mass SANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 13 Referenc

41、e detonators drawings (Figures A.1 to A.4) Dimensions in millimetres Key Key 1 Detonator shell with explosives 1 Copper shell and inner cup 2 PETN base charge 2 Electric fusehead with sealing plug 3 Inner cup and leading wires 4 Priming charge Figure A.1 - Complete detonator Figure A.2 - Loaded deto

42、nator with inner cup. SANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 14 Dimensions in millimetres Figure A.3 - Detonator shell Figure A.4 - Inner cup SANS 53763-15:2008This s tandard may only be used an

43、d printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 15 Table A.3 - Product specifications and descriptions for reference detonators Figure N Item Part Description Remarks A.1 Complete detonator 1 Detonator shell with explosives and inner cup See also Figure A

44、.2. The shell lengths A in millimetres for different charges are shown in Table A.1. Use of an inner cup, see under A.4 below. 2 Electrical fusehead with sealing plug and leading wires. The initiating energy for the detonator can be provided non electrically, i.e. by a shock tube. A.2 Loaded detonat

45、or shell with Explosives and inner cup 1 Copper shell See Figure A.3. The distance B in millimetres from the top of the inner cup or the top of the priming charge for the different type of reference detonators, see Table A.1 2/3 of the total PETN base charge pressed at 440 bars + 10 % The PETN must

46、meet the specifications given in Table A.2, and may contain up to 0,5% of carbonaceous matter to prevent electrostatic charges during handling and to improve the flow properties. 2 1/3 of the total PETN base charge Not more than 400 mg of PETN shall be compressed at any one loading operation. 3 Inne

47、r cup If used, inserted at a pressure of 440 bars + 10 % 4 Priming charge (initiation charge) compressed at 440 bars + 10 % Free choice of the substance Pressing the priming charge onto a highly compressed part of the base charge is not permitted. A.3 Detonator shell Hollow-drawn shell of pure coppe

48、r, or copper-zinc alloy with a maximum zinc mass fraction of 5 %. If required, the shells for making standard detonators should be selected by checking the exact dimensions of each shell to be used. The distances marked C, D, E and F for the different types of reference detonators are specified in m

49、illimetres in Table A.1. A.4 Inner cup (pierced) Made from CuZn 95/5 alloy. It is not required to use a pierced inner cup. SANS 53763-15:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .EN 13763-15:2004 (E) 16 Annex B (informative) Range of applicability of the test method B.1 Underwater initiating capability test The range is mainly limited by the medium in which the detonators are tested. Th