SANS 21003-2-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 2 Pipes《建筑物内部热水和冷水装置用多层管道系统 第2部分 管道》.pdf

《SANS 21003-2-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 2 Pipes《建筑物内部热水和冷水装置用多层管道系统 第2部分 管道》.pdf》由会员分享，可在线阅读，更多相关《SANS 21003-2-2008 Multilayer piping systems for hot and cold water installations inside buildings Part 2 Pipes《建筑物内部热水和冷水装置用多层管道系统 第2部分 管道》.pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21117-2 SANS 21003-2:2008 Edition 1 ISO 21003-2:2007 Edition 1SOUTH AFRICAN NATIONAL STANDARD Multilayer piping systems for hot and cold w

4、ater installations inside buildings Part 2: Pipes This national standard is the identical implementation of ISO 21003-2:2007 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pre

5、toria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa This standard may only be used and printed by approved subscription and freemailing clients of the SABS.SANS 21003-2:2008 Edition 1 ISO 21003-2:2007 Edition 1 Table of changes Change No.

6、 Date Scope National foreword This South African standard was approved by National Committee StanSA SC 5120.12K, Water and sanitation Equipment and systems Plastics pipes and fittings, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This

7、SANS document was published in May 2008. This adopted Final Draft International Standard (FDIS) has the status of a South African National Standard. The FDIS will be replaced by the final ISO document at the time of its publication. This standard may only be used and printed by approved subscription

8、 and freemailing clients of the SABS. ISO 2007 All rights reserved Document type: International Standard Document subtype: Document stage: (50) Approval Document language: E C:DOCUME1petermLOCALS1TempISO FDIS 21003-2.doc STD Version 2.1 ISO TC 138/SC 2 Date: 2007-07-1 . ISO/FDIS 21003-2:2007(E) ISO

9、TC 138/SC 2/WG 5 Secretariat: SNV Multilayer piping systems for hot and cold water installations inside buildings Part 2: Pipes Systmes de canalisations en multicouches pour installations deau chaude et froide lintrieur des btiments Partie 2: Tubes SANS 21003-2:2008This standard may only be used and

10、 printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-2:2007(E) ii ISO 2007 All rights reservedCopyright notice This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as permitted under the applicable laws of the users country, ne

11、ither this ISO draft nor any extract from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means, electronic, photocopying, recording or otherwise, without prior written permission being secured. Requests for permission to reproduce should be addressed to eithe

12、r ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Reproduction may be subject to royalty payments or a licensing agreement. Violat

13、ors may be prosecuted. SANS 21003-2:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-2:2007(E) ISO 2007 All rights reserved iiiContents Page Foreword .v Introductionvi 1 Scope1 2 Normative references1 3 Terms and definitions .

14、3 4 Symbols and abbreviated terms 3 5 Material .3 5.1 General .3 5.2 Processable materials.3 5.3 Influence on water intended for human consumption 3 6 General characteristics.3 6.1 Appearance 3 6.2 Opacity3 7 Construction3 8 Geometrical characteristics .4 8.1 General .4 8.2 Dimensions of pipes .4 9

15、Pressure strength4 9.1 Long term pressure strength (P LPL ) .4 9.2 Design pressure strength (P D )4 10 Thermal durability .4 10.1 Thermal durability P-pipes .4 10.2 Thermal durability M-pipes.5 10.2.1 Inner layer5 10.2.2 Outer layer5 11 Strength of the weld line of the M pipe .5 12 Delamination 5 12

16、.1 Multilayer P pipes5 12.2 Multilayer M pipes .5 13 Oxygen permeability of the multilayer pipe6 14 Physical and chemical characteristics6 15 Performance requirements.6 16 Marking.6 16.1 General requirements .6 16.2 Minimum required marking 7 Annex A (normative) List of reference product standards.8

17、 Annex B (normative) Design coefficient for multilayer pipes 9 B.1 Multilayer Polymer pipes (only polymer layers) with an evaluated long-term hydrostatic strength of each material and given design coefficients (Calculation method).9 B.2 Multilayer Polymer pipes (only polymer layers), LPLnot given, d

18、esign coefficients for each material given (Test method) 9 B.3 Multilayer metal pipes (polymer and metal layers) (Test Method) .9 SANS 21003-2:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-2:2007(E) iv ISO 2007 All rights r

19、eservedAnnex C (normative) Thermal durability of the outer layer of M-pipes (resistance to cracking after oven ageing) 10 C.1 Principle of the method 10 C.2 Apparatus 10 C.3 Procedure 10 C.4 Requirements 11 C.5 Example. 11 Annex D (normative) Thermal durability of the outer layer of M-pipes 12 D.1 P

20、rinciple of the method 12 D.2 Apparatus 12 D.3 Test piece preparation . 12 D.4 Procedure 12 Annex E (normative) Multilayer M-pipes - Choice of p dand the use of Miners rule. 14 E.1 Basics 14 E.2 Example for application class 2 16 E.2.1 Option 1: Use of the SEM software results 16 E.2.2 Option 2: Cho

21、ose a value for p D16 SANS 21003-2:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-2:2007(E) ISO 2007 All rights reserved vForeword ISO (the International Organization for Standardization) is a worldwide federation of nationa

22、l standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Internation

23、al organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules

24、 given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at le

25、ast 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 21003-2 was prepared by Technical Committee ISO/TC

26、138, Plastics pipes, fittings and valves for the transport of fluids, Subcommittee SC 2, Plastics pipes and fittings for water supplies. ISO 21003 consists of the following parts, under the general title Multilayer piping systems for hot and cold water installations inside buildings: Part 1: General

27、 Part 2: Pipes Part 3: Fittings Part 5: Fitness for purpose of the system Part 7: Guidance for the assessment of conformity SANS 21003-2:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-2:2007(E) vi ISO 2007 All rights reserve

28、dIntroduction The system Standard, of which this is Part 2, specifies the requirements for a multilayer piping system. The multilayer piping system is intended to be used for hot and cold water installations inside buildings. In respect of potential adverse effects on the quality of water intended f

29、or human consumption, caused by the product covered by this standard: This Standard provides no information as to whether the product may be used without restriction in any of the Member States of the EU or EFTA; It should be noted that, while awaiting the adoption of verifiable European criteria, e

30、xisting national regulations concerning the use and/or the characteristics of this product stay in force. Requirements and test methods for material and components, other than pipes, are specified in ISO 21003-1 and ISO 21003-3 of the ISO 21003-series. Characteristics for fitness for purpose (mainly

31、 for joints) are covered in 21003-5. CEN ISO/TS 21003-7 gives guidance for the assessment of conformity. This part of ISO 21003 specifies the characteristics of pipes. At the date of publication of this standard, System Standards for piping systems of plastics materials used for the same application

32、 are stated in Annex A. SANS 21003-2:2008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.FINAL DRAFT INTERNATIONAL STANDARD ISO/FDIS 21003-2:2007(E) ISO 2007 All rights reserved 1Multilayer piping systems for hot and cold water installations in

33、side buildings Part 2: Pipes 1 Scope This part of ISO 21003 specifies the characteristics of pipes for multilayer piping systems intended to be used for hot and cold water installations inside buildings for the conveyance of water whether or not intended for human consumption (domestic systems) and

34、for heating systems, under design pressures and temperatures appropriate to the class of application (see Table 1 of ISO 21003-1). It also specifies the test parameters for the test methods referred to in this standard. Part 2 of the ISO 21003-series is one part of a reference product standard. This

35、 series is applicable to multilayer pipes, fittings, their joints and to joints with components of other plastics and non-plastics materials intended to be used for hot and cold water installations in conjunction with all other parts of ISO 21003. This standard covers a range of service conditions (

36、application classes) and design pressures. For values of T D , T maxand T malin excess of those in Table 1, this standard does not apply NOTE It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirement

37、s and any relevant national regulations and installation practices or codes. The polymeric materials used for the stress designed layers are the following: polybutylene (PB), polyethylene of raised temperature resistance (PE-RT), crosslinked polyethylene (PE-X), polypropylene (PP) and chlorinated po

38、ly(vinyl chloride) (PVC-C). NOTE For the purpose of this International Standard crosslinked polyethylene (PE-X) as well as adhesives are to be considered as thermoplastic materials. PE-X shall be crosslinked and shall comply with the requirements of the reference product standard. NOTE Solid wall pi

39、pes with thin outer layers (e.g. as a protection layer or a barrier layer) are not covered by ISO 21003 but are specified in the amendments of the ISO1587x-series. The total thickness of the outer layers, including the thickness of adhesives, barrier and/or protective layers, shall be 0.4 mm. 2 Norm

40、ative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 161-1, Thermoplastics pipes

41、for the conveyance of fluids Nominal outside diameters and nominal pressures Part 1: Metric series ISO 175, Plastics Methods of test for the determination of the effects of immersion in liquid chemicals ISO 527-1, Plastics Determination of tensile properties Part 1: General principles SANS 21003-2:2

42、008This standard may only be used and printed by approved subscription and freemailing clients of the SABS.ISO/FDIS 21003-2:2007(E) 2 ISO 2007 All rights reservedISO 527-2, Plastics Determination of tensile properties Part 2: Test conditions for moulding and extrusion plastics EN 713, Plastics pipin

43、g systems Mechanical joints between fittings and polyolefin pressure pipes Test method for leak tightness under internal pressure of assemblies subjected to bending ISO 2578, Plastics Determination of time-temperature limits after prolonged exposure to heat ISO 3126, Plastics piping systems Plastics

44、 components Determination of dimensions ISO 6259-1, Thermoplastics pipes Determination of tensile properties Part 1: General test method ISO 7686, Plastics pipes and fittings Determination of opacity ISO 9080, Plastics piping and ducting systems Determination of long-term hydrostatic strength of the

45、rmoplastics material in pipe form by extrapolation ISO 10508 , Plastics piping systems for hot and cold water installations Guidance for classification and design EN 12293, Plastics piping systems Thermoplastics pipes and fittings for hot and cold water Test method for the resistance of mounted asse

46、mblies to temperature cycling ISO 13760, Plastics pipes for the conveyance of fluids under pressure Miners rule Calculation method for cumulative damage ISO 15874-2, Plastics piping systems for hot and cold water installations Polypropylene (PP) Part 2: Pipes ISO 15875-2, Plastics piping systems for

47、 hot and cold water installations Crosslinked polyethylene (PE-X) Part 2: Pipes ISO 15876-2, Plastics piping systems for hot and cold water installations Polybutylene (PB) Part 2: Pipes ISO 15877-2, Plastics piping systems for hot and cold water installations Chlorinated poly(vinyl chloride) (PVC-C)

48、 Part 2: Pipes ISO 17454, Plastics piping systems Multilayer pipes Test method for the adhesion of the different layers using a pulling rig ISO 17455, Plastics piping systems Multilayer pipes Determination of the oxygen permeability of the barrier pipe ISO 17456., Plastics piping systems Multilayer

49、pipes Determination of long-term strength ISO/DIS 21003-1, Multilayer piping systems for hot and cold water installations Part 1: General ISO/DIS 21003-3, Multilayer piping systems for hot and cold water installations Part 3: Fittings ISO/DIS 21003-5, Multilayer piping systems for hot and cold water installations Part 5: Fitness for purpose of the system ISO/FDIS 22391-2, Plastics piping systems for hot and cold water installations