SAE J 647-2010 Automotive Transmissions Schematic Diagrams《汽车变速器原理图图解》.pdf

《SAE J 647-2010 Automotive Transmissions Schematic Diagrams《汽车变速器原理图图解》.pdf》由会员分享，可在线阅读，更多相关《SAE J 647-2010 Automotive Transmissions Schematic Diagrams《汽车变速器原理图图解》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J647_201004SURFACEVEHICLERECOMMENDEDPRACTICEJ647 APR2010 Issued 1960-06Revised 2010-04 Supersed

5、ing J647 JUL1997 (R) Automatic Transmissions - Schematic Diagrams RATIONALEThis document has been updated for improved clarification and for inclusion of latest six-speed and CVT transmission schematics.FOREWORDThis document has been changed to add additional typical schematic diagrams and to show t

6、he revised one-way clutch schematic diagrams. 1. SCOPE The following schematic diagrams reflect various methods of illustrating automotive transmission arrangements. These have been developed to facilitate a clear understanding of the functional interrelations of the gearing, clutches, hydrodynamic

7、drive unit, and other transmission components. Two variations of transmission diagrams are used: in neutral (clutches not applied) and in gear. For illustrative purposes, some typical transmissions are shown. 2. REFERENCES There are no referenced publications specified herein. However, as an additio

8、nal method for transmission schematic arrangement analysis, please refer to SAE Technical Paper 810102, “Lever Analogy”. 3. TRANSMISSION IN NEUTRAL Figure 1 illustrates a six-speed layshaft dual clutch transmission. Each gear is identified according to the particular transmission speed it provides w

9、hen engaged, for example: 1st, 2nd, 3rd, and so forth. Figure 2 illustrates a four speed planetary gear transmission in neutral with clutches and bands shown disengaged. Brake bands and clutches are designated as 1st, 2nd, 3rd, reverse, and so forth, in accordance with their use. The number of teeth

10、 in each gear is shown. Figure 3 illustrates a four-speed transverse planetary gear transaxle with a chain drive connecting the two axes. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J647 Revi

11、sed APR2010 Page 2 of 8Figure 4 illustrates a four-speed longitudinal planetary gear transaxle with a chain drive connecting the main centerline to the differential. Figure 5 illustrates a five-speed planetary gear transmission. Figure 6 illustrates a six-speed planetary gear transmission. Figure 7

12、illustrates a continuously variable transmission (CVT). FIGURE 1 - SIX-SPEED DUAL CLUTCH TRANSMISSION DIAGRAM - NEUTRAL Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J647 Revised APR2010 Page 3

13、 of 8FIGURE 2 - FOUR-SPEED TRANSMISSION DIAGRAM - NEUTRAL FIGURE 3 - FOUR-SPEED TWO AXES TRANSVERSE TRANSAXLE - NEUTRAL Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J647 Revised APR2010 Page 4

14、 of 8FIGURE 4 - FOUR-SPEED LONGITUDINAL AUTOMATIC TRANSAXLE - NEUTRAL FIGURE 5 - FIVE-SPEED AUTOMATIC TRANSMISSION DIAGRAM - NEUTRAL Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J647 Revised A

15、PR2010 Page 5 of 8FIGURE 6 - SIX SPEED AUTOMATIC TRANSMISSION - NEUTRAL FIGURE 7 - CONTINUOUSLY VARIABLE TRANSMISSION (CVT) - NEUTRAL InputB1C1Output11082C014Clutches Brakes O.W.CGearC1C2C3B1B2F1Rev 1st |2nd 3rd 4th 5th 6th InputB1F1C1C2Output853138B23771C3C016 2324 Copyright SAE International Provi

16、ded by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J647 Revised APR2010 Page 6 of 84. TRANSMISSION IN GEAR 4.1 Figures 8 and 9 illustrate a six speed dual clutch transmission and a four speed planetary gear transmission in gear (or

17、iginally shown in Figures 1 and 2) engaged with the torque path denoted by straight bold arrows. Curved arrows indicate direction of shaft rotation. Active members are designated with sections crosshatched. 4.2 Dual Clutch Transmission (Figure 8) In second gear, for example, the mainshaft second gea

18、r is clutched to the output shaft. This is schematically illustrated by means of the drive dog engaging the lug in the gear. Note that the reverse gears are in mesh with each other, and the final drives are in mesh with the differential. 4.3 Planetary Gear Transmission (Figure 9) Second gear is illu

19、strated. The pertinent brake band is crosshatched to denote brake application. Additional information added to this diagram is optional: a. The rpm of the sun gear, ring gear, and carriers are designated for 100 rpm input speed. b. Clutch plate speed differential is designated for 100 rpm input spee

20、d. c. The torque of the sun gear, ring gear, and carrier is designated for 1.00 “T“ input torque. FIGURE 8 - SIX-SPEED DUAL CLUTCH TRANSMISSION DIAGRAM - 2ND SPEED Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license

21、from IHS-,-,-SAE J647 Revised APR2010 Page 7 of 8FIGURE 9 - FOUR-SPEED TRANSMISSION DIAGRAM - 2ND SPEED 5. ONE-WAY CLUTCH DIAGRAMS Figure 10 illustrates one-way clutch diagrams arranged to show direction of relative rotation between elements. FIGURE 10 - ONE-WAY CLUTCH DIAGRAM Copyright SAE Internat

22、ional Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-SAE J647 Revised APR2010 Page 8 of 86. NOTES 6.1 Marginal Indicia A change bar (l) located in the left margin is for the convenience of the user in locating areas where tech

23、nical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE SAE AUTOMATIC TRANSMISSION AND TRANSAXLE TECHNICAL STANDARDS COMMITTEE Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-