SAE AS 85049 141B-2012 CONNECTOR ACCESSORIES ELECTRICAL BOOTS HEAT-SHRINKABLE 90 DEGREE CATEGORY 7《7类90热收缩电气靴连接器附件》.pdf

《SAE AS 85049 141B-2012 CONNECTOR ACCESSORIES ELECTRICAL BOOTS HEAT-SHRINKABLE 90 DEGREE CATEGORY 7《7类90热收缩电气靴连接器附件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85049 141B-2012 CONNECTOR ACCESSORIES ELECTRICAL BOOTS HEAT-SHRINKABLE 90 DEGREE CATEGORY 7《7类90热收缩电气靴连接器附件》.pdf（10页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7AS85049/141Copyright 2017 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanic

2、al, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED2006-11REVISED2012-03R

3、EAFFIRMED 2017-05THIRD ANGLE PROJECTIONCUSTODIAN: AE-8/AE-8C1REV. BFEDERAL SUPPLY CLASS4030AS85049/141SHEET 1 OF 10REV.BPROCUREMENT SPECIFICATION: AS850496$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSXEOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJLneering sciences. The useof this report is e

4、ntirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,LVWKHVROHUHVSRQVLELOLWRIWKHXVHUSAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE invites yo

5、ur written comments and suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS85049/141BRATIONALEAS85049/141B HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY.NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBE

6、D HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS85049. FIGURE 1 RIGHT ANGLE BOOT (SEE TABLE 1) AEROSPACE STANDARD AS85049141SHEET 2 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7TABLE 1 - RIGHT ANGLE BOOT (FIGURE 1) LDIMENSION

7、 ASRECOVERED 10% 0.58(14.7)0.98(24.9)0.98(24.9)1.18(30.0)1.30(33.0)2.12(53.8)2.80(71.1)3.15(80.0)KDIMENSION ASRECOVERED 10% 0.60(15.2)0.75(19.1)0.75(19.1)0.75(19.1)0.76(19.3)1.00(25.4)1.00(25.4)1.00(25.4)UDIMENSION ASRECOVERED 10% 0.47(11.9)1.02(25.9)1.09(27.7)1.16(29.5)1.47(37.3)2.50(63.5)2.75(69.9

8、)3.12(79.2)SDIMENSION ASRECOVERED 10% 0.45(11.4)0.47(11.9)0.47(11.9)0.47(11.9)0.47(11.9)0.53(13.5)0.64(16.3)0.64(16.3)JWDIMENSION ASRECOVERED MAXIMUM 0.05(1.3) 0.05(1.3) 0.07(0.18) 0.07(0.18) 0.08(2.0) 0.13(3.3) 0.15(3.8) 0.16(4.1) HWDIMENSION ASRECOVERED 20% 0.05 (1.3) 0.06(1.5) 0.07(1.8) 0.07(1.8)

9、 0.08(2.0) 0.13(3.3) 0.15(3.8) 0.16(4.1) TDIMENSION ASRECOVERED REF 0.04(1.0) 0.04(1.0) 0.04(1.0) 0.04(1.0) 0.07(1.8) 0.07(1.8) 0.08(2.0) 0.08(2.0) RDIMENSION ASRECOVERED REF 0.65(16.5)0.76(19.3)0.83(21.1)0.90(22.9)1.14(29.0)1.32(33.5)1.64(41.7)2.03(51.6)PDIMENSION ASRECOVERED 10% 0.84(21.3)1.33(33.

10、8)1.44(36.6)1.72(43.7)2.11(53.6)3.07(78.0)3.84(97.5)4.64(117.9) JDIAMETERASRECOVERED MAXIMUM 0.24(6.1) 0.26(6.6) 0.28(7.1) 0.33(8.4) 0.39(9.9) 0.63(16.0)0.80(20.3)1.00(25.4)JDIAMETERASSUPPLIED MINIMUM MATERIALC,D, G0.47(11.9)0.58(14.7)0.63(16.0)0.73(18.5)0.87(22.1)1.39(35.3)1.80(45.7)2.25(57.2)JDIAM

11、ETERASSUPPLIED MINIMUM MATERIALA,B, H0.92(23.4)1.12(28.4)1.22(31.0)1.42(36.1)1.68(42.7)2.04(51.8)2.60(66.0)3.22(81.8)HDIAMETERASRECOVERED MAXIMUM 0.41(10.4)0.61(15.5)0.71(18.0)0.89(22.6)1.12(28.4)1.38(35.1)1.77(45.0)2.40(61.0)HDIAMETERASSUPPLIED MINIMUM 0.92(23.4)1.12(28.4)1.22(31.0)1.42(36.1)1.68(4

12、2.7)2.04(51.8)2.60(66.0)3.22(81.8)DASHNUMBER01 02 03 04 05 06 07 08AEROSPACE STANDARD AS85049141SHEET 3 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7FIGURE 2 - RIGHT ANGLE LOW PROFILE BOOT (SEE TABLE 2) AEROSPACE STANDARD AS85049141SHEET 4 OF 10REV.BCONNECTO

13、R ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7TABLE 2 - RIGHT ANGLE LOW PROFILE BOOT (FIGURE 2) RRDIMENSION ASRECOVERED 10% 0.49(12.4)0.59(15.0)0.61(15.5)0.62(15.7)0.70(17.8)0.78(19.8)0.82(20.8)0.92(23.4)0.93(23.6)1.23(31.2)PPDIMENSION ASRECOVERED 10% 0.27 (6.9) 0.33(8.4) 0.41

14、(10.4)0.48(12.2)0.61(15.5)0.72(18.3)0.83(21.1)0.95(24.1)1.18(30.0)1.31(33.3)SDIMENSION ASRECOVERED 10% 0.47(11.9)0.47(11.9)0.47(11.9)0.47(11.9)0.47(11.9)0.47(11.9)0.47(11.9)0.63(16.0)0.63(16.0)0.63(16.0)JWDIMENSION ASRECOVERED MAXIMUM0.06(1.5) 0.06(1.5) 0.06(1.5) 0.06(1.5) 0.06(1.5) 0.06(1.5) 0.06(1

15、.4) 0.06(1.4) 0.06(1.4) 0.06(1.4) HWDIMENSION ASRECOVERED 20% 0.06 (1.5) 0.06(1.5) 0.07(1.8) 0.07(1.8) 0.08(2.0) 0.08(2.0) 0.09(2.3) 0.10(2.5) 0.10(2.5) 0.10(2.5) TDIMENSION ASRECOVERED REF 0.04(1.0) 0.04(1.0) 0.04(1.0) 0.04(1.0) 0.07(1.8) 0.07(1.8) 0.07(1.8) 0.08(2.0) 0.08(2.0) 0.08(2.0) RDIMENSION

16、 ASRECOVERED REF 0.73(18.5)0.78(19.8)0.82(20.8)0.86(21.8)0.96(24.4)1.08(27.4)1.16(29.5)1.31(33.3)1.38(35.1)1.75(44.5)PDIMENSION ASRECOVERED 10% 4.14(105.2) 4.88(124.0) 5.76(146.3) 6.78(172.2) 7.29(185.2) 8.41(213.6) 8.84(224.5) 8.95(227.3) 9.19(233.4) 9.33(237.0) JDIAMETERASRECOVERED MAXIMUM0.25(6.4

17、) 0.30(7.6) 0.33(8.4) 0.39(9.9) 0.43(10.9)0.48(12.2)0.57(14.5)0.71(18.0)0.79(20.1)0.91(23.1)JDIAMETERASSUPPLIED MINIMUM MATERIALC,D, G0.55(14.0)0.63(16.0)0.72(18.3)0.84(21.3)0.91(23.1)1.07(27.2)1.24(31.5)1.54(39.1)1.70(43.2)2.01(51.1)JDIAMETERASSUPPLIED MINIMUM MATERIALA,B, H0.88(22.4)1.01(25.7)1.16

18、(29.5)1.34(34.0)1.47(37.3)1.72(43.7)1.97(50.0)2.47(62.7)2.73(69.3)3.22(81.8)HDIAMETERASRECOVERED MAXIMUM0.45(11.4)0.59(15.0)0.74(18.8)0.90(22.9)1.16(29.5)1.34(34.0)1.62(41.1)1.85(47.0)2.35(59.7)2.64(67.1)HDIAMETERASSUPPLIED MINIMUM 0.88(22.4)1.01(25.7)1.16(29.5)1.34(34.0)1.47(37.3)1.72(43.7)1.97(50.

19、0)2.47(62.7)2.73(69.3)3.22(81.8)DASHNUMBER09 10 11 12 13 14 15 16 17 18AEROSPACE STANDARD AS85049141SHEET 5 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7FIGURE 3 - RIGHT ANGLE LOW PROFILE MINIATURE BOOT (SEE TABLE 3) AEROSPACE STANDARD AS85049141SHEET 6 OF 1

20、0REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7TABLE 3 - RIGHT ANGLE LOW PROFILE MINIATURE BOOT (FIGURE 3) U 1/ DIMENSION AS RECOVERED10% 0.22 (5.6) 0.33(8.4) 0.45(11.4)0.61(15.5)SDIMENSION ASRECOVERED 10% 0.47(11.9)0.47(11.9)0.47(11.9)0.47(11.9)JWDIMENSION ASRECO

21、VERED MAXIMUM0.05(1.1) 0.05(1.1) 0.05(1.1) 0.05(1.1) HWDIMENSION ASRECOVERED 20% 0.06 (1.5) 0.07(1.8) 0.07(1.8) 0.07(1.8) TDIMENSION ASRECOVERED REF 0.04(1.0) 0.04(1.0) 0.04(1.0) 0.07(1.8) RDIMENSION ASRECOVERED REF 0.64(16.3)0.71(18.0)0.74(18.8)0.84(21.3)PDIMENSION ASRECOVERED 10% 1.75(44.5)2.65(67

22、.3)3.20(81.3)4.55(115.6) JDIAMETERASRECOVERED MAXIMUM0.08(2.0) 0.10(2.5) 0.12(3.0) 0.14(3.6) JDIAMETERASSUPPLIED MINIMUM MATERIALC,D, G0.18(4.6) 0.22(5.6) 0.26(6.6) 0.31(7.9) JDIAMETERASSUPPLIED MINIMUM MATERIALA,B, H0.25(6.4) 0.30(7.6) 0.38(9.7) 0.45(11.4)HDIAMETERASRECOVERED MAXIMUM0.51(13.0)0.75(

23、19.1)1.02(25.9)1.34(34.0)HDIAMETERASSUPPLIED MINIMUM 0.76(19.3)1.03(26.2)1.35(34.3)1.72(43.7)DASHNUMBER19 20 21 221/ DIMENSION APPLICABLE FOR INJECTION AND VENT PORT AEROSPACE STANDARD AS85049141SHEET 7 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7TABLE 4 -

24、AVAILABLE MATERIALS MATERIALDESIGNATOR 2/ MATERIAL 4/ OPERATING TEMPERATURERANGE MATERIALDESIGNATOR COLOR STRIPE 2/ SHRINKTEMPERATURE3/A 1/ POLYOLEFIN SEMI-RIGID -55 TO +135 C (-67 TO +275 F) WHITE 121 C (250 F) B 1/ POLYOLEFIN FLEXIBLE -55 TO +135 C ( -67 TO +275 F) RED100 C (212 F) CSILICONE -75 T

25、O +180 C (-103 TO +356F) ORANGE 135 C (275 F) D FLEXIBLEFLUORO-ELASTOMER -55 TO +200 C ( -67 TO +392 F) YELLOW 175 C (347 F) G 1/ POLYOLEFIN HALOGEN, FREE -30 TO +105 C (-22 TO +221 F) GREEN 120 C (248 F) H 1/ ELASTOMERIC, /-75 TO +150 C (-103 TO +275 F) BLUE135 C (275 F) 1/ OPTIONAL ADHESIVE MATERI

26、AL APPLIED ON INSIDE SURFACE SHALL BE CONTROLLED BY THE SUPPLIER TO MAINTAIN THE ADHESION AT OPERATING TEMPERATURE. 2/ MATERIAL DESIGNATOR SHALL BE A CONTINUOUS COLOR STRIPE RING, APPROXIMATELY 1/8 INCH WIDE, OR AN ENCIRCLED MATERIAL DESIGNATOR LOCATED AS SHOWN IN FIGURES 1 THRU 3. COLOR OR MATERIAL

27、 DESIGNATOR SHALL REMAIN DISTINGUISHABLE OVER THE SPECIFIED TEMPERATURE RANGE. THE SIZE OF THE MATERIAL DESIGNATOR SHALL BE RECOGNIZABLE AFTER RECOVERED, AND THE COLOR SHALL BE CONTRASTING TO THE COLOR OF THE BOOT AT THE MANUFACTURERS CHOICE. 3/ COMPONENTS SHRINK UPON APPLICATION OF HEAT IN EXCESS O

28、F VALUES LISTED. 4/ MATERIAL SHALL BE CERTIFIED TO AS5258. NOTES: 1. DIMENSIONS ARE IN INCHES2. UNLESS OTHERWISE SPECIFIED TOLERANCES SHALL BE: .XX = .020 (0.51 MM), .XXX = .010 (0.25 MM)3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 25.4 MM = 1 INCH. METRICEQUIVALENTS

29、 ARE SHOWN IN PARENTHESES.REQUIREMENTS: CONNECTOR ACCESSORY DESIGN AND CONSTRUCTION: 1. DIMENSIONS AND CONFIGURATIONS AS SPECIFIED IN FIGURES 1 THRU 3 AND TABLES 1 THRU 3. DIMENSIONS H AND JREDUCED BY 0.06 INCH (1.5 MM) WHEN ADHESIVE IS USED (SEE EXAMPLE PART NUMBER).2. MATERIAL TYPE AND IDENTIFICAT

30、ION AS SPECIFIED IN TABLE 4AEROSPACE STANDARD AS85049141SHEET 8 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 73. PART OR IDENTIFYING NUMBER (PIN) EXAMPLE:M85049/ 141 - 05 H C D P BASIC PART NUMBER SPECIFICATION SHEET DASH # (TABLE 1-3) MATERIAL DESIGNATOR (TA

31、BLE 4) ADHESIVE: C = COATED U = UNCOATED DRAIN HOLE OMIT FOR NO DRAIN HOLES INJECTION-VENT PORT OMIT FOR NO INJECTION-VENT PORT QUALIFICATIONS: THE CONNECTOR ACCESSORIES SHALL MEET QUALIFICATION REQUIREMENTS OF AS85049 CATEGORY 7 AND HEREIN. ONLY QUALIFICATION BY CERTIFICATION OF DIMENSIONS AND MATE

32、RIALS IS REQUIRED. APPLICATION NOTES: MAY BE USED IN CONJUNCTION WITH AS85049/60 (-1, AND -2 CONFIGURATIONS), AS85049/62, M85049/69, AS85049/82 THRU /90, AS85049/109 THRU /117 ADAPTERS SUPERSESSION DATA: SUPERSESSION OR EQUIVALENT DATA FOR REFERENCE ONLY MS3117 - * * * ADHESIVE (U, C) MATERIAL (A, B

33、, C) DASH NUMBER (SEE TABLE 6) TABLE 5 - AS3117 SUPERSESSION BY AS85049/141 CROSS REFERENCE DASH # MATERIAL ADHESIVE DRAIN HOLE INJECTION-VENT PORTS MS3117 /141 MS3117 /141 MS3117 /141 MS3117 /141 MS3117 /141 FIG 1 -01THRU-10 FIG 2 -09 THRU-18 BACABDCUCUREQ DNONE BLANKFIG 2 -11THRU -18 FIG 1 -01THRU

34、-08 NONE BLANKAEROSPACE STANDARD AS85049141SHEET 9 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATEGORY 7M83723-16 A * *COMPONENT DESIGNATOR/ MATERIAL- BOOT ONLY “(A”, “ (B” BACKSHELL SIZE “8 THRU 24” BOOT CONFIGURATION “A- RIGHT ANGLE” TABLE 6 - MIL-DTL-83723/16 (US

35、AF) EQUAVALENT TO AS85049/141 CROSS REFERENCE (BOOT ONLY) BACKSHELLSIZE/DASH # MATERIAL ADHESIVE DRAIN HOLE I INJECTION-VENT PORTS M83723/16 FIG 4 /141FIG 2 M83723/16 BOOT ONLY /141 M83723/16 /141 M83723/16 0/141 M83723/16 /141 81012141618202224-02 -03 -04 -04 -05 -05 -06 -06 -07 (A(BADU U REQ D NON

36、E BLANKAS5258/ 2 * * * * 46 DRAIN HOLE (D- WITH DRAIN, N- WITHOUT DRAIN) ADHESIVE (C- COATED, U- UNCOATED) DASH NUMBERMATERIAL TYPE (SEE TABLE 7) TABLE 7 - AS5258/2, /4, /6 SUPERSESSION BY AS85049/141 CROSS REFERENCE DASH # MATERIAL ADHESIVE DRAIN HOLE INJECTION-VENT PORTS AS5258 /141 AS5258 /141 AS

37、5258 /141 AS5258 /141 AS5258 /141 FIG 1 M5258/2- 01THRU 08FIG 1 01THRU08ABCDGHABCDGHCUCUREQ D NONE BLANKFIG 1 M5258/4- 01THRU 10FIG 2 09THRU18FIG 1 M5258/6- 01THRU 04FIG 3 19THRU 22AEROSPACE STANDARD AS85049141SHEET 10 OF 10REV.BCONNECTOR ACCESSORIES, ELECTRICAL BOOTS,HEAT-SHRINKABLE, 90 DEGREE,CATE

38、GORY 7M85049/68- 2 A * *ADHESIVE (C, U) DASH NUMBER (SEE TABLE 9) MATERIAL (A, B, C) FIGURE (2A, 2B) M85049/68- 7 * A MATERIAL (A, B, C) DASH NUMBER (SEE TABLE 9) FIGURE (7) TABLE 9 - MIL-C-85049/68 SUPERSESSION BY AS85049/141 CROSS REFERENCE DASH # MATERIAL ADHESIVE DRAIN HOLE INJECTION-VENT PORTS

39、M85049/68 M85049/141 M85049/68 M85049/141 M85049/68 M85049/141 M85049/68 M85049/141 M85049/68 M85049/141 FIG 2A -01 THRU -10 FIG 2 -09 THRU -18 ABCBADCUCUREQ D NONE BLANK FIG 2B -11 THRU -18 FIG 1 -01 THRU -08 NONE BLANK NONE BLANK FIG 7 5THRU 8FIG 3 -19 THRU -22 ABCABDNONE U REQ D NONE BLANK SPECIF

40、ICATION NOTES: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.