SAE AS 6450A-2012 Lubricant Application Solid Film Heat Cured Potable Water Hydraulic and Other Fluid Systems《润滑油敷用 固态膜 热固性 饮用水 液压和其他流体系统》.pdf

《SAE AS 6450A-2012 Lubricant Application Solid Film Heat Cured Potable Water Hydraulic and Other Fluid Systems《润滑油敷用 固态膜 热固性 饮用水 液压和其他流体系统》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6450A-2012 Lubricant Application Solid Film Heat Cured Potable Water Hydraulic and Other Fluid Systems《润滑油敷用 固态膜 热固性 饮用水 液压和其他流体系统》.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2012 SAE International All rights reserved. No part of this publication m

3、ay be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside U

4、SA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS6450A AEROSPACE STANDARD AS6450 REV. A Issued 2011-07 Revised 2012-11 Superseding AS6450 Lu

5、bricant Application, Solid Film, Heat Cured, Potable Water, Hydraulic, and Other Fluid Systems RATIONALE This document has been revised to add AC7108/1 Nadcap Audit Checklist, to transfer film thickness from AS6449 to AS6450 paragraph 5.4.2, to clarify handling procedures after coating, and to chang

6、e mechanic recertification interval. 1. SCOPE This SAE Aerospace Standard (AS) establishes the surface pretreatment, temperature, and baking time required to cure AS6449 Type I and Type II solid film lubricant (SFL) when it is applied over the surfaces of manufactured parts of various metals. Applic

7、ation method may be dipping or spraying. 2. REFERENCES The following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order.

8、In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 2.1 SAE Publications Available from SAE Int

9、ernational, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org. AMS2486 Conversion Coating of Titanium Alloys Fluoride-Phosphate Type AMS2488 Anodic Treatment - Titanium and Titanium Alloys Solution pH 13 or Higher

10、AMS2700 Passivation of Corrosion Resistant Steels AMS-QQ-P-416 Plating, Cadmium (Electrodeposited) AS6449 Solid Film Lubricant for Fluid Fittings in Oxygen, Potable Water, Hydraulic, and Other Systems SAE AS6450A Page 2 of 8 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Dr

11、ive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM D1125 Standard Test Methods for Electrical Conductivity and Resistivity of Water ASTM D2510 Standard Test Method for Adhesion of Solid Film Lubricants ASTM D6123 Standard Specification for Pressure-Sensitive

12、Tape for Light-Duty Packaging and General Purpose Masking ASTM F22 Standard Test Method for Hydrophobic Surface Films by the Water-Break Test 2.3 PRI Publications Available from Performance Review Institute, 161 Thorn Hill Road, Warrendale, PA 15086-7527, Tel: 724-772-1616, www.pri-network.org. PD21

13、01 Aerospace Quality Assurance , Product Standards Qualification Requirements - Fluid Distribution System AC7108/1 Nadcap Audit Criteria for Painting and Dry Film Coating AC7112/2 Nadcap Audit Criteria for Fittings and Other Machined Components AC7112/4 Nadcap Audit Criteria for Hose Assemblies 2.4

14、U.S. Government Publications Available from the Document Automation and Production Service (DAPS), Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094, Tel: 215-697-9495, https:/assist.daps.dla.mil/quicksearch/. MIL-A-8625 Anodic Coatings, for Aluminum and Aluminum Alloys 3. REQUIREMENTS 3.

15、1 Manufacturer Qualification A manufacturer coating product in accordance with this specification shall be controlled to requirements of PD2101 and AC7112/2 or AC7112/4 as applicable. Accreditation shall implement AC7108/1 requirements as applicable. NOTE: Applicators must be certified to Company Sp

16、ecifications. The applicators must be proficient and have a good knowledge of materials, tools, methods, and processes. The applicator must know the critical areas to be coated and the acceptable final appearance of the coated parts. See Appendix. 3.2 General Pretreatment and Application Instruction

17、s Do not touch the surfaces to be coated with bare hands at any time. Stir the lubricant until thoroughly mixed, using a low shear mixing blade. A mechanical paint shaker may be used, but is not recommended for waterborne coatings as excessive foaming may occur. Pretreatment, application, and cure r

18、equirements shall be as follows, unless otherwise specified on the drawing: SAE AS6450A Page 3 of 8 3.3 Pretreatment 3.3.1 Pretreatment for Aluminum Alloys Coating Type I and Type II Material - Parts shall be anodized in accordance with MIL-A-8625 Type II Class 2, color optional. Unless otherwise sp

19、ecified on the standard, parts shall not be sealed following anodizing. Parts that have not been sealed shall be coated within 16 h. In case this is not possible they may be stored for up to 6 days in sealed plastic bags until coating. They must be re-anodized if they have not been coated within 6 d

20、ays after anodizing. Preclean the surfaces to be coated with any environmentally safe cleaner that sufficiently cleans surfaces to pass ASTM F22, but does not harm the metal surface (i.e., pitting, etching, etc.). 3.3.2 Pretreatment for CRES Passivated per AMS2700 Method 1 and appropriate Class. Pre

21、clean the surfaces to be coated with any environmentally safe cleaner that sufficiently cleans surfaces to pass ASTM F22, but does not harm the surface (i.e., hydrogen embrittlement, etc.). 3.3.3 Pretreatment for Titanium and Titanium Alloys Parts shall be anodized per AMS2488 Type II, or Fluoride P

22、hosphate coated per AMS2486, except that a pretreatment, a modification of the Fluoride Phosphate treatment or a post treatment shall be applied so that the final color of the parts should be approximately gray, similar to color numbers 26081 through 26293, or 36076 through 36293 per FED-STD-595 (se

23、e 3.5.4). Sealing surfaces shall not be bead or grit blasted. Preclean the surfaces to be coated with Aliphatic Naphtha conforming to ASTM D3735 or any environmentally safe cleaner that sufficiently cleans surfaces to pass ASTM F22, but does not harm the surface (i.e., hydrogen embrittlement, etc.).

24、 3.3.4 Pretreatment for Cadmium Plated Substrate Metal (legacy material) Cadmium plate in accordance with AMS-QQ-P-416, Type III, Class 2. NOTE: Film adhesion, 3.5.1, is dependent on the active surface, application of AS6449 coating should take place as soon as possible following the application of

25、the cadmium plate. WARNING: This document references a part which contains cadmium as a plating material. Consult local officials if you have questions concerning cadmiums use. 3.4 Application Apply the lubricant using dedicated equipment, or at a minimum, equipment that has been cleaned to remove t

26、he possibility of introducing contaminates during the coating application. 3.5 Air Drying Coated parts shall be allowed to air dry for a minimum of 30 min at room temperature to assure complete removal of the solvent prior to heat curing. This air drying shall be in a location with relatively still

27、air, to protect from any ignition sources. SAE AS6450A Page 4 of 8 3.6 Curing The curing time shall be counted from the time the hardware reaches the cure temperature, not when the hardware is first placed in the curing oven. When the hardware has attained the manufacturers recommended cure temperat

28、ure, not to exceed 325.4 F (163 C) the hardware shall be cured for 2 h minimum. At the end of the curing time, the coated parts shall be removed from the oven and allowed to air cool down to room temperature. Be advised that for large parts and/or quantities of parts, it will take longer for the har

29、dware to attain the recommended cure temperature, or may require an extended cure period. 3.7 Finish Requirements 3.7.1 Film Appearance The bonded solid film lubricant, when examined as specified in 5.4.1 shall be uniform in color, smooth, free from any cracks, scratches, pinholes, blisters, bubbles

30、, runs, sags, foreign matter, grit, rough particles, or separation of ingredients. 3.7.2 Film Thickness 3.7.2.1 Flat Surfaces The average film thickness, based on six readings minimum, of the cured film shall be between 0.0003 in and 0.0005 in, with no single reading less than 0.0002 in or greater t

31、han 0.0007 in. 3.7.2.2 Internal threads For internal threads the cured film for all types shall show complete coverage of the thread pressure flanks. Film thickness shall be controlled by the process and by fit check. When installed on the appropriate thread gage or a corresponding mating test bolt

32、the coated internal threads shall permit free rotation over the full thread length specified on the standard with an AS8879 Class II maximum material condition (MMC). Thread gages shall not have flutes. 3.7.3 Film Adhesion The bonded solid film lubricant, when tested as specified in 5.4.3 shall not

33、lift or flake off to expose base substrate being coated. Following application there shall be no deposit or transfer of any coating material to the tape when examined by unaided eye. NOTE: a. Dryspray coating application may cause powdery material and transfer of material which is not acceptable. b.

34、 Black solid film lubricant powder on the inside of plastic shipping bags, after shipping and handling, shall not be cause for rejection. 4. PROCESS CONTROLS 4.1 Control Reference Parts (Specimens or test panels) Control reference part(s) (CRP) when used, shall be coated with each lot of parts being

35、 coated. The CRP shall have a minimum of one dimension taken with a minimum accuracy of 0.0001 in; the measured value and location of the measurement before and after coating on the CRP shall be identified and recorded. 4.2 Procedures The coating application, air drying, and curing procrdures shall

36、be the same for all the parts in the lot, the CRP, and any other test specimens or plate samples processed, that will be employed for qualification/confromance verification of coated parts. SAE AS6450A Page 5 of 8 5. QUALITY ASSURANCE PROVISIONS 5.1 Responsibility for Inspection The applicator is re

37、sponsible for performing all inspection requirements as specified herein. Except as otherwise specified in the contract or purchase order, and unless disapproved by the purchaser, the applicators own or any other facilities suitable for the performance of the inspection requirements specified herein

38、, may be used. The purchaser reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to assure supplies and services conform to the prescribed requirements. 5.2 Responsibility for Compliance All items shall meet all requirement

39、s of Section 3. The inspections set forth in this specification shall become part of the manufacturers overall inspection system or quality program. The absence of any inspection requirements in this specification shall not relieve the manufacturer of the responsibility of assuring that all products

40、 or supplies submitted to the purchaser for acceptance comply with all requirements of the contract or purchase order. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the procuring activity to acceptance of def

41、ective material. 5.3 Inspection Conditions 5.3.1 Atmospheric Conditions Unless otherwise specified, all examinations and tests shall be performed at a temperature of 72 F 8 F (22.5 C 4 C) and at a relative humidity between 20% and 80%. 5.4 Methods of Inspection 5.4.1 Film Appearance The bonded solid

42、 film lubricated parts shall be examined visually or at magnification of 10X and meet the requirements of 3.7.1. 5.4.2 Film Thickness Film thickness is determined after the parts have been completely cured. The thickness of the film shall meet the requirements of 3.7.2 as applicable for the area bei

43、ng inspected; these inspections shall be conducted on actual parts (providing sufficient test surface is available), or on CRPs when employed. NOTE: When possible, it is recommended that film thickness and adhesion be tested when lubricant has been applied to an end item. Testing with laboratory cou

44、pons or panels may not fully support lubrication performance when applied to actual end item. 5.4.3 Film Adhesion A strip of masking tape conforming to specification ASTM D6123 Type 1 shall be pressed firmly on the coated part surfaces (providing sufficient test surface is available), or on CRPs whe

45、n employed. The tape shall be removed with a sharp abrupt pull. Internal threaded surfaces shall be visually inspected after the Film Thickness verification to assure that the coating in the test area has not been removed. 5.5 Conformance Inspection Sampling Conformance sampling inspection shall be

46、in accordance with Table 1. Inspections shall be performed on hardware or CRPs unless otherwise agreed upon between the applicator and the purchaser, see Table 2. SAE AS6450A Page 6 of 8 TABLE 1 - SAMPLING INSPECTION Sampling Plan: C = 0 Lot Size 1 - 50 51 - 500 501 - 3200 3201+ Sample Size for all

47、Inspections 6 13 20 32 If less then 6 parts are in the lot; then all parts are to be inspected TABLE 2 - INSPECTION METHODS FOR AS6450 COATING PART ASPECT INSPECTION METHOD COUPLING NUTS THREAD FLANKS 5.4.1 FILM APPEARANCE 5.4.2 - ASSEMBLE A CLASS II MMC PLUG GAGE OVER THE ENTIRE THREAD LENGTH USING

48、 FINGER FORCE ONLY SHOULDER OR WIRE GROOVE 5.4.1 FILM APPEARANCE HEX 5.4.1 FILM APPEARANCE 5.4.3 FILM ADHESION THRUST WIRE DIAMETER 5.4.1 FILM APPEARANCE 5.4.2 - RECORD BEFORE AND AFTER COATING THICKNESS 5.4.3 FILM ADHESION 6. HANDLING AFTER COATING 6.1 Stocking SFL parts shall not be bulk packaged.

49、 Coated parts should be transported in individual compartments such as egg cartons. 6.2 Shipping Coated parts or assemblies with coated parts shall be individually packaged for shipment. If an assembly, components should have restricted movement 7. ACKNOWLEDGMENT An applicator shall mention this specification number in all quotations when acknowledging contract or purchase orders. 8. NOTES 8.1 MMC, Maximum