SAE AS 4130C-2016 ELBOW 45 ULKHEAD STANDARD AND REDUCER REDUCED BODY FLARELESS.pdf

《SAE AS 4130C-2016 ELBOW 45 ULKHEAD STANDARD AND REDUCER REDUCED BODY FLARELESS.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4130C-2016 ELBOW 45 ULKHEAD STANDARD AND REDUCER REDUCED BODY FLARELESS.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD ELBOW, 45 BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS AS4130Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopy

2、ing, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-11REVISED2016-05THIRD ANGLE

3、 PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4130 SHEET 1 OF 5 REV. C PROCUREMENT SPECIFICATION: AS18280, SEE NOTE 4 SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateoftechnicalandengineering sciences. The use of this report isentirel

4、y voluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancelled. SAE invites yourwritt

5、encomments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS4130C RATIONALE CORRECT TYPOGRAPHICAL ERRORS IN TABLES 3 AND 5. FIGURE 1 - ELBOW, 45q, BULKHEAD, REDUCED BODY, FLARELESS AEROSPACE STANDARD AS4130 SHEET

6、 2 OF 5 REV. C ELBOW, 45 BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4130 /19/ SIZE CODE H MIN J LB/EA APPROX REF CRES LB/EA APPROX REF TI 04 .050 .390 .060 .034 05 .050 .453 .072 .040 06 .050 .453 .090 .051 08 .050 .577 .169 .097 10 .070 .702

7、 .301 .172 12 .080 .890 .432 .248 16 .090 1.140 .565 .325 20 .110 1.390 1.123 .651 24 .130 1.640 1.412 .817 TABLE 2 - LEG LENGTH A FORGING SIZE 04 05 06 08 10 12 16 20 24 04 1.477 - - - - - - - - 05 1.477 1.477 - - - - - - - 06 1.540 1.540 1.586 - - - - - - 08 1.618 1.618 1.664 1.836 - - - - - 10 1.

8、711 1.711 1.757 1.929 2.070 - - - - 12 1.805 1.805 1.851 2.023 2.164 2.273 - - - 16 1.930 1.930 1.976 2.148 2.289 2.398 2.398 - - 20 1.962 1.962 2.008 2.180 2.321 2.430 2.430 2.430 - 24 1.977 1.977 2.023 2.195 2.336 2.445 2.445 2.445 2.445 TABLE 3 - LEG LENGTH B FORGING SIZE 04 05 06 08 10 12 16 20

9、24 04 .711 - - - - - - - - 05 .742 .742 - - - - - - - 06 .820 .820 .836 - - - - - - 08 .883 .883 .899 .992 - - - - - 10 .914 .914 .930 1.023 1.086 - - - - 12 1.038 1.038 1.054 1.147 1.210 1.273 - - - 16 1.132 1.132 1.148 1.241 1.304 1.367 1.367 - - 20 1.226 1.226 1.242 1.355 1.398 1.461 1.461 1.461

10、- 24 1.320 1.320 1.336 1.429 1.492 1.555 1.555 1.555 1.555 AEROSPACE STANDARD AS4130 SHEET 3 OF 5 REV. C ELBOW, 45 BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 4 - TURN LENGTH K FORGING SIZE 04 05 06 08 10 12 16 20 04 .540 - - - - - - - 05 .560 .560 - - - - - - 06 .635 .635 - - - -

11、- - 08 .635 .635 .635 - - - - - 10 .635 .685 .685 .735 - - - - 12 .635 .635 .685 .785 .835 - - - 16 .735 .735 .735 .835 .885 .985 - - 20 .775 .775 .785 .885 .930 1.000 1.000 - 24 .820 .820 .825 .915 .970 1.040 1.040 1.040 TABLE 5 - FITTING END SIZE CODE TUBE OD T THREAD PER AS8879 CLASS 3A D E 04 25

12、0 .4375-20UNJF .371 .350 05 .313 .5000-20UNJF .371 .412 06 .375 .5625-18UNJF .379 .453 08 .500 .7500-16UNJF .461 .577 10 .625 .8750-14UNJF .511 .702 12 .750 1.0625-12UNJ .556 .890 16 1.000 1.3125-12UNJ .556 1.140 20 1.250 1.6250-12UNJ .556 1.390 24 1.500 1.8750-12UNJ .556 1.640 NOTES: NOTICE THIS DO

13、CUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL a. CODE LETTER J: TYPE 304 CORROSION RESISTANT STEEL PER AMS5639 b. CODE LETTER T: TYPE 6Al-4V TITANIUM ALLOY PER AMS4928 c. CODE LETTER V: TYPE

14、15-5PH CORROSION RESISTANT STEEL PER AMS5659 2. HEAT TREATMENT a. MATERIAL CODE LETTER J: NONE b. MATERIAL CODE LETTER T: NONE c. MATERIAL CODE LETTER V: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 AEROSPACE STANDARD AS4130 SHEET 4 OF 5 REV. C ELBOW, 45 BULKHEAD, STANDARD AND REDUCER, REDUCED BODY,

15、 FLARELESS /3/ FINISH a. MATERIAL CODE LETTER J: PASSIVATE PER AMS2700 TYPE 6 OR 7 b. MATERIAL CODE LETTER T: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 c. MATERIAL CODE LETTER V: (1) NO SUFFIX FINISH CODE LETTER: PASSIVATE PER AMS2700 TYPE 2 OR 8 (2) SUFFIX FINISH CODE LETTER “P”; CADMIUM PLATE

16、 PER AMS-QQ-P-416, TYPE II, CLASS 2 /4/ PROCUREMENT SPECIFICATION: AS18280 UNLESS SPECIFIED OTHERWISE ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL

17、-AS18280 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS”, MATERIAL CODE LETTER AND

18、 FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING 6. THIS PART IS INTENDED FOR USE IN SYSTEMS

19、 WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -04 THROUGH -16 AT 3000 PSI B. SIZES -20 AND -24 AT 1500 PSI NOTE: OPERATING PRESSURES HAVE BEEN CHANGED FROM 4000 PSI AND 2000 PSI TO 3000 PSI AND 1500 PSI TO COMPLY WITH AS18280 SYSTEM PRESSURE REQUIREMENTS. USERS OF THIS STANDARD FOR 4000 PSI SYSTEM

20、APPLICATIONS ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. /7/ FOR SHOULDER DIAMETER ON BULKHEAD REDUCERS: a. USE “S” DIAMETER (OF AS4377) FOR SMALLER BULKHEAD END SIZE ON ONE STEP REDUCTIONS (E.G., 08 FORGING TO 06 BULKHEAD END, USE “S” FOR 06 BULKHEAD AS SHOU

21、LDER DIAMETER) b. USE “J” OF FORGING FOR TWO STEP OR GREATER REDUCTIONS (E.G., 08 FORGING TO 04 BULKHEAD END, USE “J” DIAMETER FOR 08 FORGING AS SHOULDER DIAMETER) 8. WHEN MACHINED FROM BAR OR OVERSIZED FORGING, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 2. /9/ RADIUS APPLICABLE TO TITAN

22、IUM PARTS ONLY. 10. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 11. THIS PART IS A REDUCED BODY VERSION OF MS21907 IF NONREDUCER, OR AS1010 IF REDUCER. /12/ SPECIFY END SIZES IN THIS ORDER: BULKHEAD END FIRST (PORT #1), REMAINING END SECOND (PORT #2). 13. LARGEST END DETERMINES FORGING SIZE

23、. /14/ APPLICABLE ONLY TO REDUCERS AND SIZE 04 AND 05 NONREDUCERS. 15. INTERPRETATION OF DRAWING PER ARP4296. 16. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 17. DIMENSIONS AND TOLERANCING: ANSI Y14.5

24、M-1982. 18. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS .5q. AEROSPACE STANDARD AS4130 SHEET 5 OF 5 REV. C ELBOW, 45 BULKHEAD, STANDARD AND REDUCER, REDUCED BODY, FLARELESS /19/ EXAMPLE OF PART NUMBER: 20. REVISION INDICATOR: A CHANGE BAR

25、(l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNI

26、CAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 21. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. SIZE CODE, TUBE SIZE OF PORT #2 IN .062 INCH INCREMENTS /12/ SIZE CODE, TUBE SIZE OF PORT #1 IN .062 INCH INCREMENTS /12/