SAE AS 39029 17B-2010 CONTACTS ELECTRICAL CONNECTOR SOCKET CRIMP REMOVABLE (FOR MIL-C-81511 SERIES 3 CONNECTORS)《卷曲可移除的插座电连接器的触点(MIL-C-81511系列3连接器)》.pdf

《SAE AS 39029 17B-2010 CONTACTS ELECTRICAL CONNECTOR SOCKET CRIMP REMOVABLE (FOR MIL-C-81511 SERIES 3 CONNECTORS)《卷曲可移除的插座电连接器的触点(MIL-C-81511系列3连接器)》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 39029 17B-2010 CONTACTS ELECTRICAL CONNECTOR SOCKET CRIMP REMOVABLE (FOR MIL-C-81511 SERIES 3 CONNECTORS)《卷曲可移除的插座电连接器的触点(MIL-C-81511系列3连接器)》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD CONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE (FOR MIL-C-81511 SERIES 3 CONNECTORS) AS39029/17Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, el

2、ectronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED

3、2000-06REVISED 2010-10THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.BFEDERAL SUPPLY CLASS 5999 AS39029/17SHEET 1 OF 4REV. BPROCUREMENT SPECIFICATION: AS39029SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Th

4、euse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancell

5、ed. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS39029/17BRATIONALE A REVISION IS REQUIRED TO CORRECT THE POSITIONERS IN TABLE 3, THE POSITIONERS LISTED IN /17A ARE INCORRECT.

6、NOTE-THE /7 TOOL IS NO LONGER LISTED IN TABLE 3 BECAUSE IT WILL NOT WORK WITH THESE END (RATHER THAN SHOULDER) POSITIONED CONTACTS. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF: SAE AS39029. FIGURE 1 - AS39029/17

7、 SOCKET Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/17SHEET 2 OF 4REV. BCONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE (FOR MIL-C-81511 SERIES 3 CONNECTORS) TA

8、BLE 1 - CONTACT DIMENSIONS BINCODEADIABDIACDIADMAXDIAEMINDIAONLY HDIAL(REF) M N P R S T U MAXWCHAM 171.0480 .0465 .0200 .0180 .0555 (1.41) .0540 (1.37) .055 .028.022.018.937(23.80) .445.425.155.145.218.208.145.139.726.716.250.190 .038.006.003172.0480 .0465 .0355 .0335 .0555 (1.41) .0540 (1.37) .055

9、.028.022.018.937(23.80) .445.425.155.145.218.208.145.139.726.716.250.190 .038.006.003173.0615 .0600 .0450 .0430 .0760 (1.93) .0745 (1.89) .076 .0415 .027.023.937(23.80) .395.375.195.185.218.208.165.159.726.716.360.270 .045.007.004174.0925 .0910 .0645 .0625 .1080 (2.74) .1065 (2.71) .108 .064.027.023

10、.937(23.80) .370.350.195.185.218.208.165.159.726.716.360.270 .045.010.006175.1515 .1500 .1020 .0980 .1695 (4.31) .1680 (4.27) .169 .0955 .042.038.954(24.23) .370.350.232.216.245.235.196.190.726.716.360.250 .050.012.006TABLE 2 - MARKING AND DESIGN CHARACTERISTICS BINCODE COLOR BANDS MATINGEND SIZEWIR

11、EBARRELSIZETYPE CLASS 1ST2ND3RD171 BROWN VIOLET BROWN 23 28 A B 172 BROWN VIOLET RED 23 22 173 BROWN VIOLET ORANGE 20 20 174 BROWN VIOLET YELLOW 16 16 175 BROWN VIOLET GREEN 12 12 TABLE 3 - TOOL REQUIREMENTS BINCODE BASIC CRIMPING TOOL POSITIONER INSTALLINGTOOL REMOVAL TOOL WIREDCONTACT UNWIRED CONT

12、ACT 171 M22520/2-01 M22520/2-16 M81969/16-04 M81969/16-04 M81969/30-01 172 M22520/2-01 M22520/2-16 M81969/16-04 M81969/16-04 M81969/30-01 173 M22520/2-01 M22520/2-17 M81969/16-01 M81969/16-01 M81969/30-02 174 M22520/2-01 M22520/2-18 M81969/16-02 M81969/16-02 M81969/30-03 175 M22520/1-01 M22520/1-10

13、M81969/16-03 M81969/16-03 M81969/30-04 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/17SHEET 3 OF 4REV. BCONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE (FOR MIL-

14、C-81511 SERIES 3 CONNECTORS) TABLE 4 - PART NUMBERS AS39029 PART NUMBER BINCODE SUPERSEDEDPART NUMBER(S) M39029/17-171 171 M39029/17-23-28 M39029/17-172 172 M39029/17-23-22 M39029/17-173 173 M39029/17-20-20 M39029/17-174 174 M39029/17-16-16 M39029/17-175 175 M39029/17-12-12 DETAIL SPECIFICATION REQU

15、IREMENTS: 1. DESIGN: CONTACT SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1, TABLE 1 AND 2. DIMENSIONS ARE IN INCHES AND SHOWN AFTER PLATING. UNLESS OTHERWISE SPECIFIED, SPHERICAL END DIMENSIONS SHALL CONFORM TO AS39029. ALL DIMENSIONS PROVIDED IN PARENTHESES ARE METRIC EQUIVALENTS AND GIVEN FOR GENE

16、RAL INFORMATION ONLY (SEE AS39029 SECTION 6). DIMENSION “U” IS THE POINT OF INITIAL ENGAGEMENT. THERE SHALL BE A MAXIMUM GAP OF .008 INCHES BETWEEN THE HOOD AND BODY OF THE CONTACT. A 0.002 IN. MAXIMUM BURR IS PERMITTED ON THE PERIPHERY OF SHOULDER NOTED (SEE VIEW X). 2. TOOLS: TOOLS REQUIRED FOR CR

17、IMPING CONTACTS TO WIRE/CABLE AND THE INSTALLING/REMOVAL FROM THE CONNECTOR SHALL BE IN ACCORDANCE WITH TABLE 3. 3. PART NUMBERS: CONTACT PART NUMBERS SHALL BE IN ACCORDANCE WITH TABLE 4. SUPERSEDED PART NUMBERS ARE AS SPECIFIED. 4. MATERIALS: MATERIALS SHALL BE IN ACCORDANCE WITH AS39029. 5. MECHAN

18、ICAL: MECHANICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. 6. ELECTRICAL: ELECTRICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. 7. ENVIRONMENTAL: ENVIRONMENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. VIBRATION SHALL BE IN ACCORDANCE WITH EIA-364-28 TEST CONDITION IV WITH A TEMPERA

19、TURE CYCLE IN ACCORDANCE WITH TEST CONDITION I. TEST THE CONTACT IN THE HIGHEST TEMPERATURE RATED, MIL-C-81511 CONNECTOR SERIES. THE MINIMUM TEMPERATURE SHALL BE -65 (+0, -3) C. THE DURATION OF TIME AT THE TEMPERATURES STEPS 1 AND 3 SHALL BE 25% OF THE TIME DETERMINED BY THE SPECIFIED CONNECTOR MASS

20、. THERE SHALL BE A MINIMUM OF 10% OR NOT LESS THAN THREE MATED CONTACTS WIRED IN SERIES. THE CONTACT RESISTANCE SHALL NOT INCREASE MORE THAN 5 OHMS DURING 1 MICROSECOND. SHOCK SHALL BE IN ACCORDANCE WITH EIA-364-27 TEST CONDITION A. PERFORM ONE SHOCK IN EACH AXIS. THERE SHALL BE A MINIMUM OF 10% OR

21、NOT LESS THAN THREE MATED CONTACTS WIRED IN SERIES. THE CONTACT RESISTANCE SHALL NOT EXCEED 5 OHMS IN 1 MICROSECOND. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/17SHEET

22、 4 OF 4REV. BCONTACTS, ELECTRICAL CONNECTOR, SOCKET, CRIMP REMOVABLE (FOR MIL-C-81511 SERIES 3 CONNECTORS) 8. APPLICATION NOTES: CONTACT IS INACTIVE FOR NEW DESIGN. AS39029/17 SOCKET CONTACT MATES WITH AN AS39029/18 PIN AS SHOWN IN TABLE 5. TABLE 5 - CONTACT MATING PART NUMBERS AS39029/17 BIN CODE 1

23、/MATING AS39029/18 BIN CODE 2/171 176 172 177 173 178 174 179 175 180 1/ SOCKET IS USED IN MIL-C-81511 SERIES 4 CONNECTOR 2/ PIN IS USED IN MIL-C-81511 SERIES 3 AND 4 CONNECTOR9. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISI

24、ONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-