SAE AMS 5629H-2016 Steel Corrosion-Resistant Bars Wire Forgings Rings and Extrusions 13Cr - 8 0Ni - 2 2Mo - 1 1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Tr.pdf
《SAE AMS 5629H-2016 Steel Corrosion-Resistant Bars Wire Forgings Rings and Extrusions 13Cr - 8 0Ni - 2 2Mo - 1 1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Tr.pdf》由会员分享,可在线阅读,更多相关《SAE AMS 5629H-2016 Steel Corrosion-Resistant Bars Wire Forgings Rings and Extrusions 13Cr - 8 0Ni - 2 2Mo - 1 1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Tr.pdf(10页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2016 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5629H AEROSPACE MATERIAL SPECIFICATION AMS5629 REV. H Issued 1968-11 Reaffirme
5、d 2006-10 Revised 2016-08Superseding AMS5629G Steel, Corrosion-Resistant, Bars, Wire, Forgings, Rings, and Extrusions 13Cr - 8.0Ni - 2.2Mo - 1.1Al Vacuum Induction Plus Consumable Electrode Melted Solution Heat Treated, Precipitation Hardenable (Composition similar to UNS S13800)RATIONALE AMS5629H r
6、esults from a Limited Scope Ballot to add the requirements of AS6279 (3.8), and also revises Properties (3.5.2.2.2) and Reports (4.4.7). 1. SCOPE 1.1 Form This specification covers a corrosion-resistant steel in the form of bars, wire, forgings, flash welded rings, and extrusions 12 inches (305 mm)
7、and under in nominal diameter, thickness or for hexagons, least distance between parallel sides, and stock of any size for forging, flash welded rings, or extrusion (see 8.7). 1.1.1 For purchase of solution treated and aged product, use the applicable AMS slash specification (see 8.5). If a slash sh
8、eet description is not specified, solution annealed material shall be supplied. A specific example of a slash specification is: AMS5629/H1000 Precipitation Hardened to H1000 condition 1.2 Application These products have been used typically for parts requiring corrosion resistance, stress-corrosion r
9、esistance, high strength up to 600 F (316 C), and good ductility and strength in the transverse direction in large section sizes, but usage is not limited to such applications. 1.2.1 Certain design and processing procedures may cause these products to become susceptible to stress-corrosion cracking;
10、 ARP1110 recommends practices to minimize such conditions. 1.3 Classification Steels covered by this specification are classified as follows: SAE INTERNATIONAL AMS5629H Page 2 of 10 1.3.1 Melting Practice Type 1 - Steel multiple melted using vacuum-arc consumable electrode process in the final melt
11、cycle Type 2 - Steel multiple melted using electroslag consumable electrode process in the final melt cycle. 1.3.1.1 When a type is not specified, Type I shall be supplied. 1.3.2 Maximum Delta Ferrite Content Class A 0.5% max., free ferrite Class B 1.0% max., free ferrite Class C 2.0% max., free fer
12、rite. 1.3.2.1 When no class is specified, any class may be supplied. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a subsequent revision of a documen
13、t unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-
14、0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2241 Tolerances, Corrosion and Heat-Resistant Steel, Iron Alloy, Titanium, and Titanium Alloy Bars and Wire AMS2248 Chemical Check Analysis Limits Corrosion and Heat-Resistant Steels and Alloys, Maragin
15、g and Other Highly-Alloyed Steels, and Iron Alloys AMS2300 Steel Cleanliness, Premium Aircraft-Quality Magnetic Particle Inspection Procedure AMS2315 Determination of Delta Ferrite Content AMS2371 Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steels and Alloys Wrought Products
16、and Forging Stock AMS2374 Quality Assurance Sampling and Testing Corrosion and Heat-Resistant Steel and Alloy Forgings AMS2750 Pyrometry AMS2806 Identification Bars, Wire, Mechanical Tubing, and Extrusions Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and Alloys AMS2808 Identificat
17、ion Forgings AMS7490 Rings, Flash Welded Corrosion and Heat-Resistant Austenitic Steels, Austenitic-Type Iron, Nickel, or Cobalt Alloys, or Precipitation-Hardenable Alloys ARP1110 Minimizing Stress Corrosion Cracking in Wrought Forms of Steels and Corrosion Resistant Steels and Alloys SAE INTERNATIO
18、NAL AMS5629H Page 3 of 10 ARP1917 Clarification of Terms Used in Aerospace Metals Specifications AS6279 Industry Standard Practices for Production, Distribution, and Procurement of Metal Stock 2.2 ASTM Publications Available from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshoh
19、ocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org. ASTM A370 Mechanical Testing of Steel Products ASTM A604 Macroetch Testing of Consumable Electrode Remelted Steel Bars and Billets ASTM E112 Determining Average Grain Size ASTM E140 Hardness Conversion Tables for Metals Relationship Among Brinel
20、l Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, Scleroscope Hardness, and Leeb Hardness ASTM E353 Chemical Analysis of Stainless, Heat-Resisting, Maraging, and Other Similar Chromium-Nickel-Iron Alloys 3. TECHNICAL REQUIREMENTS 3.1 Composition Shall conform to
21、the percentages by weight shown in Table 1, determined by wet chemical methods in accordance with ASTM E353, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - Composition Element min max Carbon - 0.05 Manganese - 0.10 Silicon - 0.10 Phosphorus - 0.010 Sulf
22、ur - 0.008 Chromium 12.25 13.25 Nickel 7.50 8.50 Molybdenum 2.00 2.50 Aluminum 0.90 1.35 Nitrogen - 0.010 3.1.1 Check Analysis Composition variations shall meet the applicable requirements of AMS2248 except that no variation over maximum is permitted for nitrogen. 3.2 Melting Practice Shall be multi
23、ple melted using vacuum induction practice followed by either vacuum or, when specified, electroslag consumable electrode remelting (see 1.3). SAE INTERNATIONAL AMS5629H Page 4 of 10 3.3 Condition The product shall be supplied in the following condition: 3.3.1 Bars and Wire 3.3.1.1 Rounds Centerless
24、 ground or turned after solution heat treatment. 3.3.1.2 Hexagons, Squares, and Flats Cold finished, solution heat treated, straightened, and descaled, or hot finished, solution heat treated, straightened, and descaled, as ordered. 3.3.1.2.1 Bar shall not be cut from plate (also see 4.4.5). 3.3.2 Fo
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS5629H2016STEELCORROSIONRESISTANTBARSWIREFORGINGSRINGSANDEXTRUSIONS13CR80NI22MO11ALVACUUMINDUCTIONPLUSCONSUMABLEELECTRODEMELTEDSOLUTIONHEATTRPDF

链接地址:http://www.mydoc123.com/p-1022063.html