SAE AIR 6114-2016 Interface for Micro Munition (IMM) Handbook.pdf
《SAE AIR 6114-2016 Interface for Micro Munition (IMM) Handbook.pdf》由会员分享,可在线阅读,更多相关《SAE AIR 6114-2016 Interface for Micro Munition (IMM) Handbook.pdf(33页珍藏版)》请在麦多课文档分享上搜索。
1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2016 SAE InternationalAll rights reserved. No part of this publi
3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out
4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AIR6114AEROSPACEINFORMATION REPORTAIR6114Issued 2016-09Interface for Micro Munition (IMM) Han
5、dbookRATIONALEThis handbook provides information on the implementation of the Interface Standard, Interface for Micro Munitions (IMM), as defined in AS5726, into both current and future Micro Munition Hosts and Micro Munitions. This handbook provides guidance on design considerations, background inf
6、ormation and rationale on AS5726 requirements, and other useful information for implementation of the IMM interface.TABLE OF CONTENTS1. SCOPE 31.1 Scope 31.2 Background . 31.3 Application. 32. REFERENCES 32.1 Applicable Documents 32.1.1 General 32.1.2 SAE Publications. 32.1.3 ANSI Publications . 42.
7、1.4 Government Publications 42.2 Definitions . 42.3 Acronyms and Abbreviations 53. GENERAL . 63.1 Interface Set and Classes. 63.1.1 Overlay of Digital Data and Power Interfaces. 83.1.2 Digital Data Interfaces. 83.1.3 Mated Status Interface 83.1.4 Safety Enable Discrete Interface 93.1.5 Power Interfa
8、ces . 93.1.6 Structure Ground Interface . 104. COMMENTARY ON THE REQUIREMENTS OF AS5726 . 104.1 Host Requirements . 104.1.1 Host: Mated Status Interface . 104.1.2 Host: Safety Enable Discrete Interface. 124.1.3 Host: Fibre Channel Interface 134.1.4 Host: Power Interfaces. 144.1.5 Host: Structure Gro
9、und Interface 194.2 Micro Munition Requirements . 194.2.1 Micro Munition: Mated Status Interface . 194.2.2 Micro Munition: Safety Enable Discrete Interface 204.2.3 Micro Munition: Fibre Channel Interface 21SAE INTERNATIONAL AIR6114 Page 2 of 334.2.4 Micro Munition: Power Interfaces. 224.2.5 Micro Mu
10、nition: Structure Ground Interface. 254.3 Interface Initialization 254.3.1 Host Initialization Requirements . 264.3.2 Micro Munition Initialization Requirements . 274.4 Power Interface Interrupts. 284.4.1 Micro Munition Compatibility . 284.4.2 Host Compatibility . 284.4.3 Micro Munition Power Interr
11、upt Notification 294.5 Fibre Channel and Power Overlay Requirements 294.5.1 Power and Data Interface Isolation Requirements . 294.6 Connector Characteristics. 314.6.1 Connector Usage 314.6.2 MMHI Connector . 324.6.3 IMM Connector 324.6.4 Contacts 324.6.5 Connector Insert Arrangement 324.6.6 Connecto
12、r Location and Orientation . 335. NOTES 335.1 Revision Indicator 33FIGURE 1 IMM SIGNAL SET FROM FIGURE 1 OF AS5726 7FIGURE 2 DIGITAL DATA AND POWER INTERFACES SCHEMATIC FROM FIGURE 2 OF AS5726. 8FIGURE 3 MATED STATUS INTERFACE SCHEMATIC FROM FIGURE 3 OF AS5726 . 11FIGURE 4 XAMPLE OF A SAFETY-CRITICA
13、L FUNCTION 15FIGURE 5 ISOLATION NETWORK SCHEMATIC FROM FIGURE 9 OF AS5726 30FIGURE 6 CONNECTOR USAGE EXAMPLE FROM FIGURE 10 OF AS5726 31TABLE 1 STANDARD MAPS OF UFC AND DFC FROM FC-PI TO IMM SIGNALS. 13TABLE 2 TANDARD OVERLAYS OF FIBRE CHANNEL AND POWER SIGNALS 14SAE INTERNATIONAL AIR6114 Page 3 of
14、331. SCOPE1.1 ScopeThis document was prepared by the SAE AS-1B1 IMM Task Group to explain and document background information and design decisions made during the development of AS5726. This handbook is published separately to preserve information that is not required or provided in the AS5726 but m
15、ay be important to system designers to ensure interoperability between the Micro Munition Host and Micro Munition. As a handbook, it cannot be invoked as a requirement in a contract.The structure and numbering of this document mirrors that of AS5726 for the convenience of readers. Headings such as “
16、Requirements” in this handbook should not be interpreted as invoking requirements.1.2 BackgroundThe information contained in this handbook is intended to provide the Micro Munition system designer with the following types of information:x A thorough understanding of the requirements imposed by AS572
17、6.x Identification of design problem areas that could contribute to an interface incompatibility.x A presentation of design techniques, components and design practices that might be useful in implementing A5726.x Practical guidance and associated rationale for users of AS5726 in future applications.
18、1.3 ApplicationThis handbook is applicable to AS5726, Revision A only.2. REFERENCES2.1 Applicable DocumentsThe following publications form a part of this document to the extent specified herein. The latest issue of SAE publications shall apply. The applicable issue of other publications shall be the
19、 issue in effect on the date of the purchase order. In theevent of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been ob
20、tained.2.1.1 GeneralThe documents listed in this section are referenced in Sections 3, 4, and 5 of this handbook.2.1.2 SAE PublicationsAvailable from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.
21、sae.org.AS5653 High Speed Network for MIL-STD-1760AS5725 Interface Standard, Miniature Mission Store InterfaceAS5726 Interface Standard, Interface for Micro MunitionsSAE INTERNATIONAL AIR6114 Page 4 of 332.1.3 ANSI PublicationsCopies of these documents are available online at http:/webstore.ansi.org
22、/.FC-PI ANSI INCITS 352-2002 Fibre Channel Physical interfaces2.1.4 Government PublicationsCopies of these documents are available online at http:/quicksearch.dla.mil.Specifications, Standards, and HandbooksThe following specifications, standards, and handbooks form a part of this document to the ex
23、tent specified herein.MIL-DTL-38999 Connectors, Electrical, Circular, Miniature, High Density, Quick Disconnect (Bayonet, Threaded, and Breech Coupling), Environment Resistant, Removable Crimp and Hermetic Solder Contacts, General Specification ForMIL-STD-704 Department of Defense Interface Standard
24、 for Aircraft Electrical Power CharaceteristicsMIL-HDBK-1760 Department of Defense Handbook for Aircraft/Store Electrical Interconnection SystemMIL-STD-1760 Department of Defense Interface Standard for Aircraft/Store Electrical Interconnection SystemRevision EMIL-STD-8591 Department of Defense Desig
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAIR61142016INTERFACEFORMICROMUNITIONIMMHANDBOOKPDF

链接地址:http://www.mydoc123.com/p-1020354.html