NEMA C136 19-2017 Roadway and Area Lighting Equipment - High-Pressure Sodium (HPS) and Retrofit HPS Lamps for Mercury Ballasts - Guide for Selection.pdf

《NEMA C136 19-2017 Roadway and Area Lighting Equipment - High-Pressure Sodium (HPS) and Retrofit HPS Lamps for Mercury Ballasts - Guide for Selection.pdf》由会员分享，可在线阅读，更多相关《NEMA C136 19-2017 Roadway and Area Lighting Equipment - High-Pressure Sodium (HPS) and Retrofit HPS Lamps for Mercury Ballasts - Guide for Selection.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、NEMA Standards PublicationNational Electrical Manufacturers AssociationANSI C136.19-2017Roadway and Area Lighting Equipment High-Pressure Sodium (HPS) and Retrofit HPS Lamps for Mercury Ballasts Guide for SelectionANSI C136.19-2017 American National Standard for Roadway and Area Lighting Equipment H

2、igh-Pressure Sodium (HPS) and Retrofit HPS Lamps for Mercury Ballasts Guide for Selection Secretariat: National Electrical Manufacturers Association Approved June 27, 2017 American National Standards Institute, Inc. ANSI C136.19-2017 Page ii 2017 National Electrical Manufacturers Association NOTICE

3、AND DISCLAIMER The information in this publication was considered technically sound by the consensus of persons engaged in the development and approval of the document at the time it was developed. Consensus does not necessarily mean that there is unanimous agreement among every person participating

4、 in the development of this document. ANSI standards and guideline publications, of which the document contained herein is one, are developed through a voluntary consensus standards development process. This process brings together volunteers and/or seeks out the views of persons who have an interes

5、t in the topic covered by this publication. While NEMA administers the process to promote fairness in the development of consensus, it does not write the document and it does not independently test, evaluate, or verify the accuracy or completeness of any information or the soundness of any judgments

6、 contained in its standards and guideline publications. NEMA disclaims liability for any personal injury, property, or other damages of any nature whatsoever, whether special, indirect, consequential, or compensatory, directly or indirectly resulting from the publication, use of, application, or rel

7、iance on this document. NEMA disclaims and makes no guaranty or warranty, expressed or implied, as to the accuracy or completeness of any information published herein, and disclaims and makes no warranty that the information in this document will fulfill any of your particular purposes or needs. NEM

8、A does not undertake to guarantee the performance of any individual manufacturer or sellers products or services by virtue of this standard or guide. In publishing and making this document available, NEMA is not undertaking to render professional or other services for or on behalf of any person or e

9、ntity, nor is NEMA undertaking to perform any duty owed by any person or entity to someone else. Anyone using this document should rely on his or her own independent judgment or, as appropriate, seek the advice of a competent professional in determining the exercise of reasonable care in any given c

10、ircumstances. Information and other standards on the topic covered by this publication may be available from other sources, which the user may wish to consult for additional views or information not covered by this publication. NEMA has no power, nor does it undertake to police or enforce compliance

11、 with the contents of this document. NEMA does not certify, test, or inspect products, designs, or installations for safety or health purposes. Any certification or other statement of compliance with any health- or safety-related information in this document shall not be attributable to NEMA and is

12、solely the responsibility of the certifier or maker of the statement. ANSI C136.19-2017 Page i 2017 National Electrical Manufacturers Association AMERICAN NATIONAL STANDARD Approval of an American National Standard requires verification by The American National Standards Institute, Inc. (ANSI) that

13、the requirements for due process, consensus, and other criteria for approval have been met by the standards developer. An American National Standard implies a consensus of those substantially concerned with its scope and provisions. Consensus is established when, in the judgment of the ANSI Board of

14、 Standards Review, substantial agreement has been reached by directly, and materially affected interests. Substantial agreement means much more than a simple majority, but not necessarily unanimity. Consensus requires that all views and objections be considered, and that a concerted effort be made t

15、oward their resolution. The existence of an American National Standard does not in any respect preclude anyone, whether s/he has approved the standard or not, from manufacturing, marketing, purchasing, or using products, processes, or procedures not conforming to the standards. It is intended as a g

16、uide to aid the manufacturer, the consumer, and the general public. The American National Standards Institute, Inc., does not develop standards and will in no circumstances give an interpretation of any American National Standard. Moreover, no person shall have the right or authority to issue an int

17、erpretation of an American National Standard in the name of the American National Standards Institute, Inc. Requests for interpretations should be addressed to the secretariat or sponsor whose name appears on this title page. CAUTION NOTICE: This American National Standard may be revised or withdraw

18、n at any time. The procedures of the American National Standards Institute, Inc., require that action be taken periodically to reaffirm, revise, or withdraw this standard. Purchasers of American National Standards may receive current information on all standards by calling or writing the American Na

19、tional Standards Institute, Inc. Published by National Electrical Manufacturers Association 1300 North 17thStreet, Suite 900 Rosslyn, Virginia 22209 2017 National Electrical Manufacturers Association All rights, including translation into other languages, reserved under the Universal Copyright Conve

20、ntion, the Berne Convention for the Protection of Literary and Artistic Works, and the International and Pan American copyright conventions. No part of this publication may be reproduced in any form, in an electronic retrieval system or otherwise, without prior written permission of the publisher. P

21、rinted in the United States of America ANSI C136.19-2017 Page ii 2017 National Electrical Manufacturers Association CONTENTS 1 Scope 1 2 Normative References 1 3 Informative References . 1 4 General Description and Information 1 TABLES Table 1 Standard High-Pressure Sodium Lamps . 3 Table 2 Retrofit

22、 High-Pressure Lamps 5 Table 3 Non-Cycling High-Pressure Sodium Lamps 6 Table 4 Standby/Instant Restrike (Dual-Arc) High-Pressure Sodium Lamps . 7 ANSI C136.19-2017 Page 1 2017 National Electrical Manufacturers Association 1 Scope This standard covers the selection of high-pressure sodium lamps reco

23、mmended for use in roadway and area lighting equipment. 2 Normative References This standard incorporates by undated reference provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed below. For undated references

24、, the latest edition of the publication referred to applies (including amendments). ANSI C78.42-2009 American National Standard, High-Pressure Sodium Lamps ANSI C81.61-1990 (R1996) American National Standard for Electrical Lamp Bases ANSI C82.4-2002 American National Standard for Lamp BallastsBallas

25、ts for High-Intensity Discharge and Low-Pressure Sodium Lamps (Multiple-Supply Type) ANSI C82.7-1988 American National Standard, Specifications for Mercury Lamp Transformers, Constant Current (Series) Supply Type Note: ANSI Standards are available from Global Engineering Documents, 15 Inverness Way

26、East, Englewood, CO 80112-5776 Phone: 303/397-7956, Fax 303/397-2740, email: , or . 3 Informative References This standard is intended to be used in conjunction with the following publication. The latest edition of the publication applies (including amendments). ANSI C78.380-2002, American National

27、Standard for High-intensity Discharge Lamps, Method of Designations 4 General Description and Information 4.1 High-pressure sodium lamps may be operated on either series or multiple circuits with the use of the proper ballast. 4.2 The lamps in Tables 1 through 4 conform to the applicable requirement

28、s of ANSI C81.61 and ANSI C78.42. 4.3 Lamps listed in Table 1 are intended for use with ballasts meeting the requirements of ANSI C82.4, applying to ballasts for high-pressure sodium lamps. 4.4 Lamps listed in Table 2 are intended for use with ballasts meeting the requirements of ANSI C82.7, applyin

29、g to ballasts for mercury lamps. 4.5 Lamps of other wattages and color in combination with the proper ballast and with the same dimensional characteristics may be used in the same equipment, provided the operating temperature of the alternate lamp-ballast combinations do not exceed those of the lamp

30、-ballast combinations used in the original equipment. ANSI C136.19-2017 Page 2 2017 National Electrical Manufacturers Association 4.6 Users should consult their selected lamp manufacturer for type availability and exceptions to the appropriate lamp information table. 4.7 Lamp bases of brass or a cor

31、rosion resistant alloy are recommended. Consult the manufacturer for availability. ANSI C136.19-2017 Page 3 2017 National Electrical Manufacturers Association Table 1 Standard High-Pressure Sodium Lamps Watts Arc Tube Voltage Lamp Base ANSI Code Initial Lumens Rated Avg Life (hrs) MOL mm (in) LCL mm

32、 (in) A. Standard LampsMogul Base Clear 50 52 B25/E23.5 E39 MOG S68 4000 24000+ 197 (7.75) 127 (5.0) 70 52 B25/E23.5 E39 MOG S62 6300 24000+ 197 (7.75) 127 (5.0) 100 55 B25/E23.5 E39 MOG S54 9400 24000+ 197 (7.75) 127 (5.0) 150 55 B25/E23.5 E39 MOG S55 15800 24000+ 197 (7.75) 127 (5.0) 150 100 B28/E

33、28 E39 MOG S56 16000 24000+ 211 (8.31) 127 (5.0) 200 100 E18 E39 MOG S66 21400 24000+ 248 (9.75) 146 (5.75) 250 100 E18 E39 MOG S50 29000 24000+ 248 (9.75) 146 (5.75) 250 100 E18 E39 MOG S50 29000 24000+ 248 (9.75) 127 (5.0) 310 100 E18 E39 MOG S67 37000 24000+ 248 (9.75) 146 (5.75) 400 100 E18 E39

34、MOG S51 50000 24000+ 248 (9.75) 146 (5.75) 400 100 B37/E37 E39 MOG S51 50000 24000+ 287 (11.31) 178 (7.0) 600 110 T15 E39 MOG S106 90000 24000+ 285 (11.22) 170 (6.69) 750 120 B37/E37 E39 MOG S111 105000 24000+ 287 (11.31) 178 (7.0) 1000 250 E25 E39 MOG S52 130000 24000+ 383 (15.06) 222 (8.75) 1000 2

35、50 B37/E37 E39 MOG S52 130000 24000+ 287 (11.31) 178 (7.0) Diffuse 50 52 B25/E23.5 E39 MOG S68 3700 24000+ 197 (7.75) 70 52 B25/E23.5 E39 MOG S62 5800 24000+ 197 (7.75) 100 55 B25/E23.5 E39 MOG S54 8610 24000+ 197 (7.75) 150 55 B25/E23.5 E39 MOG S55 14000 24000+ 197 (7.75) 250 100 E18 E39 MOG S50 26

36、000 24000+ 248 (9.75) 400 100 E18 E39 MOG S51 47500 24000+ 248 (9.75) ANSI C136.19-2017 Page 4 2017 National Electrical Manufacturers Association B. Standard LampsE26 (Medium) Base Clear 35 52 B17/ED17 E26 MED S76 2250 16000 138 (5.43) 87 (3.41) 50 52 B17/ED17 E26 MED S68 4000 24000+ 138 (5.43) 87 (

37、3.41) 70 52 B17/ED17 E26 MED S62 6300 24000+ 138 (5.43) 87 (3.41) 100 55 B17/ED17 E26 MED S54 9500 24000+ 138 (5.43) 87 (3.41) 150 55 B17/ED17 E26 MED S55 15800 24000+ 138 (5.43) 87 (3.41) Diffuse 35 52 B17/ED17 E26 MED S76 2100 16000 138 (5.43) 50 52 B17/ED17 E26 MED S68 3800 24000+ 138 (5.43) 70 5

38、2 B17/ED17 E26 MED S62 5950 24000+ 138 (5.43) 100 55 B17/ED17 E26 MED S54 8800 24000+ 138 (5.43) 150 55 B17/ED17 E26 MED S55 14500 24000+ 138 (5.43) Continued from previous page ANSI C136.19-2017 Page 5 2017 National Electrical Manufacturers Association Table 2 Conversion LampsMercury or Metal Halid

39、e to High Pressure Sodium Watts Arc Tube Voltage Lamp Base ANSI Code Initial Lumens Rated Avg Life (hrs) MOL mm (in) LCL mm (in) A. Conversion LampsMogul Base B. Selected Mercury Lag, Reactor and Constant Current Series ballasts (1) Clear 150 130 B28/E28 E39 MOG M57/H39 11800 24000 211 (8.31) 127 (5

40、.00) 215 130 B28/E28 E39 MOG M58/H37 20000 16000 211 (8.31) 127 (5.00) 360 135 B37/E37 E39 MOG M59/H33 38000 24000 292 (11.46) 178 (7.00) 880 260 E25 E39 MOG M47/H36 101000 12000 383 (15.06) 241 (9.50) Diffuse 150 130 B28/E28 E39 MOG M57/H39 12000 24000 211 (8.31) 360 135 B37/E37 E39 MOG M59/H33 360

41、00 24000 291 (11.46) C. Conversion Lamps-Mogul Base D. Selected Mercury or Metal Halide Multiple Ballasts Without Peaking Capacitor Clear 150 130 B28 E39 MOG M57/H39 15000 24000 211 (8.31) 127 (5.00) 220 130 B28 E39 MOG M58/H37 25000 24000 211 (8.31) 127 (5.00) 360 135 B37 E39 MOG M59/H33 45000 2400

42、0 291 (11.46) 178 (7.0) 940 265 B56 E39 MOG M47/H36 130000 24000 391 (15.39) 241 (9.5) 940* 265 E25 E39 MOG M47/H36 130000 24000 383 (15.06) 222 (8.75) *MH to HPS conversion only Diffuse 150 130 B28 E39 MOG M57/H39 14500 24000 211 (8.31) 220 130 B28 E39 MOG M58/H37 24000 24000 211 (8.31) 360 135 B37

43、 E39 MOG M59/H33 43000 24000 291 (11.46) 940 265 B56 E39 MOG M47/H36 123000 24000 391 (15.39) 1Consult the lamp manufacturer for the specific application. ANSI C136.19-2017 Page 6 2017 National Electrical Manufacturers Association Table 3 Non-Cycling High-Pressure Sodium Lamps Watts Arc Tube Voltage

44、 Lamp Base ANSI Code Initial Lumens Rated Avg Life (hrs) MOL mm (in) LCL mm (in) Non-Cycling Standard LampsE39 (Mogul Base) Clear 50 52 E23.5 E39 MOG S68 3800 24000+ 197 (7.75) 127 (5.00) 70 52 E23.5 E39 MOG S62 6300 24000+ 197 (7.75) 127 (5.00) 100 55 E23.5 E39 MOG S54 9800 24000+ 197 (7.75) 127 (5

45、.00) 150 55 E23.5 E39 MOG S55 16000 24000+ 197 (7.75) 127 (5.00) 200 100 E18 E39 MOG S66 22000 24000+ 248 (9.75) 146 (5.75) 250 100 E18 E39 MOG S50 28500 24000+ 248 (9.75) 146 (5.75) 310 100 E18 E39 MOG S67 37000 24000+ 248 (9.75) 146 (5.75) 400 100 E18 E39 MOG S51 49000 24000+ 248 (9.75) 146 (5.75)

46、 1000 250 E25 E39 MOG S52 130000 24000+ 383 (15.06) 222 (8.75) Non-Cycling Standard Lamps26 (Medium Base) Clear 70 52 B17 E26 MED S62 6300 24000+ 138 (5.43) 87 (3.41) 100 55 B17 E26 MED S54 9800 24000+ 138 (5.43) 87 (3.41) ANSI C136.19-2017 Page 7 2017 National Electrical Manufacturers Association T

47、able 4 Standby/Instant Restrike (Dual Arc Tube) High-Pressure Sodium Lamps Watts Arc Tube Voltage Lamp Base ANSI Code Initial Lumens Rated Avg Life (hrs) MOL mm (in) LCL mm (in) Standby/Instant Restrike (Dual Arc Tube) High-Pressure Sodium Lamps (Mogul Base) Clear 50 52 E23.5 E39 MOG S68 3800 40000

48、197 (7.75) 127 (5.00) 70 52 E23.5 E39 MOG S62 6050 40000 197 (7.75) 127 (5.00) 100 55 E23.5 E39 MOG S54 9500 40000 197 (7.75) 127 (5.00) 150 55 E23.5 E39 MOG S55 15700 40000 197 (7.75) 127 (5.00) 200 100 E18 E39 MOG S66 21500 40000 248 (9.75) 146 (5.75) 250 100 E18 E39 MOG S50 27500 40000 248 (9.75)

49、 146 (5.75) 400 100 E18 E39 MOG S51 47500 40000 248 (9.75) 146 (5.75) 1000 250 E25 E39 MOG S52 127000 40000 383 (15.06) 222 (8.75) Note: The individual arc tubes have the same arc tube voltage. They are wired in parallel. The ANSI ballast designation is the same. NATIONAL ELECTRICAL MANUFACTURERS ASSOCIATION 1300 NORTH 17TH STREET, SUITE 900 ROSSLYN. VA 22209www.NEMA.orgTO ORDER ADDITIONAL NEMA STANDARDS VISITWWW.GLOBAL.IHS.COM OR CALL 1-800-854-7179/1-303-397-79565612_0514TB