NAVY UFGS-08 34 49 00 20-2006 HEMP SHIELDED DOOR《麻质屏蔽门(代替 NAVY UFGS-13095N)》.pdf

《NAVY UFGS-08 34 49 00 20-2006 HEMP SHIELDED DOOR《麻质屏蔽门(代替 NAVY UFGS-13095N)》.pdf》由会员分享，可在线阅读，更多相关《NAVY UFGS-08 34 49 00 20-2006 HEMP SHIELDED DOOR《麻质屏蔽门(代替 NAVY UFGS-13095N)》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、*USACE / NAVFAC / AFCESA / NASA UFGS-08 34 49.00 20 (April 2006)-Preparing Activity: NAVFAC Replacing without changeUFGS-13095N (September 1999)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated 1 April 2006*SECTION TABLE OF CONTENTSDIVISION 08 - OPENINGSSECTION 08 34

2、 49.00 20HEMP SHIELDED DOOR04/06PART 1 GENERAL1.1 REFERENCES1.2 DEFINITIONS1.2.1 Regularly Engaged1.2.2 Independent1.2.3 Shielding Attenuation1.2.4 Corrections and Repair1.2.5 Modification1.3 SUBMITTALS1.4 QUALITY ASSURANCE1.4.1 Qualifications1.4.1.1 HEMP Shielded Door Manufacturer1.4.2 Regulatory R

3、equirements1.4.3 Certification of Welders1.4.4 Welding Procedure1.4.5 Installation Details1.4.6 HEMP Shielded Door1.5 DELIVERY, STORAGE, AND HANDLING1.6 COORDINATION1.7 WARRANTY1.8 MAINTENANCE1.8.1 Hardness Maintenance and Hardness Surveillance (HM/HS) Manual1.8.2 Spare PartsPART 2 PRODUCTS2.1 HEMP

4、SHIELDED DOOR AND FRAME2.1.1 Pneumatic Type Door2.1.1.1 Sealing System2.1.2 Sliding Type Door2.1.3 Electromagnetic Type Door (Swinging or Sliding)2.1.4 Latching Type2.1.4.1 Finger-Stock (Contact Finger)2.1.5 Door and Frame Assembly2.2 HINGESSECTION 08 34 49.00 20 Page 1Provided by IHSNot for ResaleN

5、o reproduction or networking permitted without license from IHS-,-,-2.3 HARDWARE AND ACCESSORIES2.3.1 Power Assist2.3.2 Threshold Protectors2.3.3 Locks and Interlocks2.3.3.1 Cipher Locks2.3.3.2 Interlocks2.3.4 Threshold Alarm2.3.5 Hold Open Device2.3.6 Counting Device2.3.7 Door Stop2.4 EMERGENCY EXI

6、T HEMP SHIELDED DOOR2.5 PAINTING2.6 TOOLS2.7 ELECTRIC CONNECTIVITY2.8 MAINTENANCE SUPPLIES AND PROCEDURES2.9 SOURCE QUALITY CONTROL2.9.1 Swinging Door Static Load Test2.9.2 Swinging Door Sag Test2.9.3 Door Closure Test2.9.4 Handle Pull Test2.9.5 Electromagnetic SA Test2.9.5.1 Test Frequencies (Facto

7、ry Test)2.9.5.2 Test Methodology2.9.5.3 Test Instruments and Equipment2.9.5.4 Calibration and Recalibration2.9.5.5 Inspection2.9.5.6 Independent Tester2.9.6 ELECTROMAGNET (EM) SHIELDED DOOR TESTS2.9.6.1 EM R.F. Seal Breaking Force2.9.6.2 SA Due to Residual Magnetism (RM)2.9.6.3 SA Due to Inner or Ou

8、ter or Both EM CoilsPART 3 EXECUTION3.1 HEMP SHIELDED DOOR FRAME AND ASSEMBLIES3.2 HEMP DOOR FRAME ACCESSIBILITY3.3 HEMP SHIELDED DOOR INSTALLATION3.4 POST INSTALLATION PROTECTION3.5 FIELD QUALITY CONTROL3.5.1 Tests3.5.1.1 Final Acceptance Test3.5.2 EM Shielded Door Tests3.5.2.1 SA Due to RM3.5.2.2

9、SA Due to Inner or Outer or Both EM Coils3.6 TRAINING3.7 SITE SPECIFIC REPAIRS AND TEMPORARY FIXES3.8 RETESTS3.9 EMERGENCY EXIT PANIC HARDWARE FIELD MODIFICATION3.10 WELDING- End of Section Table of Contents -SECTION 08 34 49.00 20 Page 2Provided by IHSNot for ResaleNo reproduction or networking per

10、mitted without license from IHS-,-,-*USACE / NAVFAC / AFCESA / NASA UFGS-08 34 49.00 20 (April 2006)-Preparing Activity: NAVFAC Replacing without changeUFGS-13095N (September 1999)UNIFIED FACILITIES GUIDE SPECIFICATIONSReferences are in agreement with UMRL dated 1 April 2006*SECTION 08 34 49.00 20HE

11、MP SHIELDED DOOR04/06*NOTE: This guide specification covers the requirements for furnishing and installing high-altitude electromagnetic pulse (HEMP) shielded door.Comments and suggestions on this guide specification are welcome and should be directed to the technical proponent of the specification.

12、 A listing of technical proponents, including their organization designation and telephone number, is on the Internet.Recommended changes to a UFGS should be submitted as a Criteria Change Request (CCR).Use of electronic communication is encouraged.Brackets are used in the text to indicate designer

13、choices or locations where text must be supplied by the designer.*NOTE: Show the following information on the project drawings:a. Location of HEMP shielded door.b. Location of alarm panel.*PART 1 GENERAL1.1 REFERENCES*NOTE: This paragraph is used to list the publications cited in the text of the gui

14、de specification. The publications are referred to in the text by basic designation only and listed in this paragraph by organization, designation, date, and title.SECTION 08 34 49.00 20 Page 3Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Use the R

15、eference Wizards Check Reference feature when you add a RID outside of the Sections Reference Article to automatically place the reference in the Reference Article. Also use the Reference Wizards Check Reference feature to update the issue dates.References not used in the text will automatically be

16、deleted from this section of the project specification when you choose to reconcile references in the publish print process.*The publications listed below form a part of this specification to the extent referenced. The publications are referred to within the text by the basic designation only.AMERIC

17、AN WELDING SOCIETY (AWS)AWS D1.1/D1.1M (2006) Structural Welding Code - SteelAWS D9.1M/D9.1 (2000) Sheet Metal Welding CodeASTM INTERNATIONAL (ASTM)ASTM A 36/A 36M (2005) Carbon Structural SteelASTM A 366/A 366M (1997e1) Commercial Steel, Sheet, Carbon,(0.15 Maximum Percent Cold-RolledASTM A 568/A 5

18、68M (2005) Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements forASTM A 569/A 569M (1998) Steel, Carbon (0.15 Maximum Percent), Hot-Rolled Sheet and Strip, CommercialASTM B 194 (2001e1) Copper-Beryllium Alloy Plate, Sheet, Strip, and Rolled BarNATION

19、AL FIRE PROTECTION ASSOCIATION (NFPA)NFPA 101 (2006) Life Safety CodeNFPA 80 (1999) Fire Doors and Fire WindowsNFPA 80A (2001) Protection of Buildings from Exterior Fire ExposuresU.S. DEPARTMENT OF DEFENSE (DOD)MIL-STD-188-125 (Rev A) High-Altitude Electromagnetic Pulse (HEMP) Protection for Ground-

20、Base C41 Facilities Performing Critical, Time-Urgent Missions, Volume I Fixed FacilitiesSECTION 08 34 49.00 20 Page 4Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-285 (Basic, Notice 1) Attenuation Measurements for Enclosures, Electromagneti

21、c Shielding, for Electronic Test Purposes1.2 DEFINITIONS1.2.1 Regularly EngagedAs it applies to the testing company is defined to mean that the testing company has successfully performed electromagnetic shielding attenuation (SA) test and shielded enclosure leak detection system (SELDS) tests at lea

22、st six _ times in the last two _ years.1.2.2 IndependentAs it applies to the testing company is defined to mean that the company has no financial interest and not directly or indirectly part of the shielding Contractor, subcontractor, or general contractor QC organization.1.2.3 Shielding Attenuation

23、As it applies to this section is defined as the shielding effectiveness. Shielding effectiveness at a test area for the purpose of this procedure is the ratio expressed in decibels (dB), of the received signal when the receiving antenna is illuminated by electromagnetic radiation in the test calibra

24、tion configuration (no shield present) to the received signal through the electromagnetic barrier in the test measurement configuration. Assuming that antenna voltage is detected.SE = 20 log(Vc/Vm)Where Vm is the measured signal at the test area and Vc is the calibration signal at the same frequency

25、 and transmitting antenna polarization. Shielding effectiveness values are test-method dependent and different values may be obtained when time-domain or other frequency-domain measurement techniques are used.1.2.4 Corrections and RepairReplacing existing defective part(s) with identical parts which

26、 are shown in approved shop drawings, parts list, catalog, and maintenance manual. This includes cleaning, adjustment, and tightening.1.2.5 ModificationAdding new part(s) like pieces or extra row(s) of finger-stocks, gasket (all shapes and sizes), bronze wool, microwave absorber which are not shown

27、in drawings, parts list, catalog, and maintenance manual.1.3 SUBMITTALS*NOTE: Review submittal description (SD) definitions in Section 01 33 00 SUBMITTAL PROCEDURES and edit the following list to reflect only the submittals required for the project. Submittals should be kept to the minimum required

28、for adequate quality control.A “G” following a submittal item indicates that the SECTION 08 34 49.00 20 Page 5Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-submittal requires Government approval. Some submittals are already marked with a “G”. Only

29、delete an existing “G” if the submittal item is not complex and can be reviewed through the Contractors Quality Control system. Only add a “G” if the submittal is sufficiently important or complex in context of the project.For submittals requiring Government approval on Army projects, a code of up t

30、o three characters within the submittal tags may be used following the “G“ designation to indicate the approving authority. Codes for Army projects using the Resident Management System (RMS) are: “AE“ for Architect-Engineer; “DO“ for District Office (Engineering Division or other organization in the

31、 District Office); “AO“ for Area Office; “RO“ for Resident Office; and “PO“ for Project Office. Codes following the “G“ typically are not used for Navy, Air Force, and NASA projects.Choose the first bracketed item for Navy, Air Force and NASA projects, or choose the second bracketed item for Army pr

32、ojects.*Government approval is required for submittals with a “G“ designation; submittals not having a “G“ designation are for Contractor Quality Control approval.for information only. When used, a designation following the “G“ designation identifies the office that will review the submittal for the

33、 Government. The following shall be submitted in accordance with Section 01 33 00 SUBMITTAL PROCEDURES:SD-02 Shop Drawings*NOTE: Typical installation of frames and HEMP shielded door(s) shall be based in accordance with manufacturers installation drawings.*HEMP shielded door installation; GElectric

34、connectivity; GInstallation details; GSD-03 Product DataShielded door and frame; GHardware and accessories; GHinges; GPanic hardware; GSD-06 Test ReportsSECTION 08 34 49.00 20 Page 6Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Swinging door static

35、 load test; GSwinging door sag test; GDoor closure test; GHandle pull test; GElectromagnetic SA test; GElectromagnet (EM) shielded door tests; GSubmit test reports for specified tests under paragraph entitled “Source Quality Control.“ Test reports shall contain as minimum, list of equipment used wit

36、h calibration data, test point location, date, project title and location, location of signal source, dynamic range, noise floor, SA (required and actual), any repair performed, person performing the test and witness signature.SD-07 CertificatesCertification of welders; GTest compliance of HEMP shie

37、lded door; GSD-08 Manufacturers InstructionsTest plan; GWelding procedure; GSD-10 Operation and Maintenance Data*NOTE: Designer should consult with the Engineering Service Center, Code 065, on DNA-TR-91-87 HM/HS Manual.*Hardness Maintenance and Hardness Surveillance (HM/HS) Manual, Data Package 3; G

38、Submit in accordance with Section 01 78 23 OPERATION AND MAINTENANCE DATA.SD-11 Closeout SubmittalsFinal acceptance testEM shielded door tests*NOTE: Check with using agency, if test report needs to be classified secret top secret.*Submit test reports for specified tests under paragraph entitled “Fie

39、ld Quality Control.“ Test reports shall contain as a minimum, list of equipment used with calibration data, test point location, SECTION 08 34 49.00 20 Page 7Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-date, project title and location, location o

40、f signal source, dynamic range, noise floor, SA (required and actual), any repair performed, person performing the test and witness signature. Test report is classified secret top secret _, therefore, the independent tester shall have the necessary security clearance. Log the test data for each test

41、 point on the form as the test progresses. Have the witness sign the data form at the end of each day.1.4 QUALITY ASSURANCE1.4.1 Qualifications1.4.1.1 HEMP Shielded Door ManufacturerProvide supervision and installation of work required under this section by the HEMP shielded door manufacturer. HEMP

42、shielded door manufacturer shall have successfully manufactured and completed at least 3 _ similar HEMP shielded door projects of comparable size in the last 1 _ year.1.4.2 Regulatory RequirementsFire rated HEMP shielded door and assemblies shall meet NFPA 80 and NFPA 80Arequirements and bear the id

43、entifying label of a nationally recognized testing agency qualified to perform certification programs.1.4.3 Certification of WeldersBefore assigning welders to work covered by this section, submit the names of the welders to be employed, together with certification that each welder has passed the qu

44、alification tests in the process specified in AWS D1.1/D1.1Mand AWS D9.1M/D9.1. Contractor shall require a welder to retake the tests when, in the opinion of the Contracting Officer, the work of the welder creates a reasonable doubt as to the proficiency of the welder. Recertification of the welder shall be made to the Contracting Officer only after welder