NAVY MIL-W-17965 B-1970 WEBBING TEXTILE KNITTED NYLON ELASTIC 4-1 4 INCH WIDTH《4-1 4英尺宽弹性尼龙编织的纺织带》.pdf
《NAVY MIL-W-17965 B-1970 WEBBING TEXTILE KNITTED NYLON ELASTIC 4-1 4 INCH WIDTH《4-1 4英尺宽弹性尼龙编织的纺织带》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-W-17965 B-1970 WEBBING TEXTILE KNITTED NYLON ELASTIC 4-1 4 INCH WIDTH《4-1 4英尺宽弹性尼龙编织的纺织带》.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、I NIL-W-37765B 83 7777706 0383032 m MIL-W- I7965B(MC) 2 July 1970 SUPERSEDING MIL-W-l7965A(#C) 31 July 1964 MILITARY SPECIFICATION WEBBIG, TEXTILE: KNITTED, NYLOH; ELASTIC; 4-1/4 NcH WIDTH , 1. SCOPE *l.l This specification covers requirements for one type of knitted nylon, elastic webbing, 2. APPLI
2、CABLE WCUHENTS *2.1 The following documents of the issue in effect on date of imitation for bids or request for ProPoW, form a part of the specification to the extent specified herein. SPECIFICATIONS MILITARY MIL-u-43334 - Webbing And Tape, Textile, Packaging And Packing Of. STANDARDS FEDERAL FED-ST
3、D-191 - Textile Test Methods. FED-STD-601 - Rubber; Sampling And Testing. MILITARY MIL-STD-105 - Sampling Procedures And Tables For Inspection By Attributes. (Copies of specifications and standards required by suppliers in connection with specific procurement functions should be obtained from the pr
4、ocuring activity or as directed by the contracting officer.) t2.2 Other publications. The following d!xument forPo a part of this specifi- cation to the extent specified herein. Unless otherwise indicated, the issue In effect on date of invitation for bids or request for proposal shall apply. Rules
5、and Regulations Under the Textile Fiber Products Identification Act (Copies may be obtained from the-Federal Trade Commission, Washington, D. C. 20580, Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MXL-W-17965B (MC) 3. BEQu1-s *3.1 Sample. Samples
6、are furnished solely for guidance and information Variation from the specification may appear in to the supplier (see 6.3). the sample, in which case the specification shall govern. *3.2 First article, Unless otherwise specified (see 6.21, before production is commenced, finished webbing shall be su
7、bmitted, or made available, to the contracting officer or his authorized representative for approval. of the first article authorizes the commencement of production, but does not relieve the supplier of responsibility for compliance with all provisions of this specification. The first article shall
8、be manufactured by the supplier at the same facilities to be used for the manufacture of the production item, The approval *3.3 W.teria1. “ha webbing rh.11 ba made of SO gage utrudad natural round rubber eastic strand8 wrapped with 70 denier and 200 denier nylon yarnr. knitting yarns shall be 210 de
9、nier nylon yarn (see Section 4, Table III for required test). The “3.4 Design. The webbing shall conform to the requirements specified in Table I when tested as specified in Section 4, Table V. Table L. Physical requirements Characteriotic Widtb-inches: -web portion -selvage -overall nickners-inch i
10、ieight-euncee per linear yard rotal sewing sections (warp direction) Number of ende per sewing section divieion Wales per inch Ribs per inch (filling direction) Color (unless otherwise specified) -wet (dry) cleaning -crocking -light -perspiration Colorfaetnees to: Requirement 3-112 1: 1/16 3/8 + 1/3
11、2 4-if4 118 0,038 f: .O3 2e2 - 2.6 6 mnimum 6 mnimum 22 5 2 19 5 2 -106 Goad Good Good Good 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-W-17765B 83 W 7797706 0383034 MIL-W-17965B (MC) *3,4.1 Ultimate elongation and ruNure evidence f ruptur
12、e of rubber strands when the webbing is subjected to an ultimate elongation of 200 percent in the filling direction. *3.5 Construction. The knitted webbing shall have a transverse web of inter- locking and interconnecting warp and filling yarns with a selvage at each edge. The laid in elaBtic warps
13、shall consist of a rubber core wrapped first with 2-ply, 70 denier, 1/2 twist nylon and then wrapped with single ply, 200 denier, 112 twist nylon (see Section 4, Table III for required teet) . *3.6 LenPth of roll. Unless otherwise specified (see 6.21, the webbing shall be furnished in rolls of not l
14、ess than 33 yards. There shall not be more than 3 pieces per roll and the minimum length of any one piece shall be 10 yards. ticket attached to the roll in accordance with MIL-W-43334. *3.8 Fiber identification. Each roll of webbing shall be labeled, ticketed or invoiced for fiber content in accorda
15、nce with the Textile Fiber Praducts Identification Act. of rubber strands. There shall be no *3.7 Identification tickets. Each roll of webbing shall have an identification *3.9 Workmanshie. The finished elastic webbing shall conform to the quality and grade of product established by this specificati
16、on. defects shall not exceed the levels set by the applicable quality levels (AQL). The occurrence of 4. QUALITY ASSWCE PROVISIONS *4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the supplier ia respnnsible for the performance of all inspection requi
17、rements as specified herein. the contract or order, the supplier may use his own or any other facilities suitable for the performance of the inspection requireaients specified herein, unless disapproved by the Government. The Government resenres the right to perform any of the inspections set forth
18、in the specification where such inspections are deemed necessary to assure supplies and services conforte to preecribed requirements. Except as otherwise specified in *4.1.1 Certificate of compliance, Where certificates of compliance are submitted, the Government reserves the right to check test suc
19、h item to determine the validity of the certification. *4,.2 Inspection. Inspection shall be in accordance with the provision6 oat forth in HIL-STD-105, except where otherwise indicated herein. *4.2.1 First article inspection. The first article submitted in accordance with 3.2 shall be visually insp
20、ected for appearance and color. shall be tested for physical and chemical properties in Section 3 in accordance with methods specified in 4.3. The first article *4.2.2 Testing of components. Components listed in Table II shall be tested The sample unit shall be one cone, tube, or spool and for the c
21、haracteristics specified herein in accordance with the referenced.test methods of FED-STD-191. the lot size shall be expressed in units of one cone, tube, or spool each. The lot shall be unacceptable if one or more units fail to meet any requirement specified. The sample size shall be as follows: Pr
22、ovided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-i mIL-W-L77658 3 m 7777706 0381035 y T m Xn-W-17965B (MC) 22,001 and aver T8ble II n I Characteristic Hylon yam: -Material Identific8tion Denier TUI%L), twist Rubber Yarn: Uaterial identification Bege Sam
23、ple size 2 3 5 rtiag of components R.4 I Test para, I method 3.3 3.3 3.5 - i/ 4021 4052 &/ 3.3 3.3 i/ I- 4.3.1 l/ The aupplier shall submit a certificate of compliance for the characteTietAc listad. iaepection, or other verifi8be quality dat8. “p.te or-fail“ The certificate rital1 be accompuiid by a
24、ctual teat, 2/ One determination per aaiqple unit and the resulte reported (u *4,2.3 Examhition of the end item. The irabbing ihall br dixMinad to determine conformance with the requireirants of thicr spectficatioa. this axdnation shall be Cl8Bdfied in accordance wth4.2.3.1, 4.2.3.2 and Defects foun
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILW17965B1970WEBBINGTEXTILEKNITTEDNYLONELASTIC414INCHWIDTH414 英尺 弹性 尼龙 编织 纺织 PDF

链接地址:http://www.mydoc123.com/p-983189.html