NAVY MIL-W-17337 F-1989 WEBBING TEXTILE WOVEN NYLON《机织尼龙织物边带》.pdf

《NAVY MIL-W-17337 F-1989 WEBBING TEXTILE WOVEN NYLON《机织尼龙织物边带》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-W-17337 F-1989 WEBBING TEXTILE WOVEN NYLON《机织尼龙织物边带》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、r , ? MIL-W-17337F i :. 11. December 1989 SUPERSEDING 9 November 1982 MIL-W-17337E MILITARY SPECIFICATION WEBBING, TEXTILE, WOVEN NYLON -t This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requiremen

2、ts for woven nylon webbing, woven on shuttle or shuttleless looms. 1.2 Classification. The webbing shall be one of type, and shall be procured in the following classes as specified (see 6.2). 1.2.1 Class. The class of webbing shall consist of the following: Class 1 - Lifesaving Equipment (Shuttle Co

3、nstruction - Nylon 6,6) Class 2 - Loadcarrying Equipment (Shuttle or Shuttleless Construction - Nylon 6 or Nylon 6,6) Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clot

4、hing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8305 DISTRIBUTION STATEMENT A. Approved for public release; . distri

5、bution is unlimited. 9 * . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-17337F 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards and handbooks form a par

6、t of this document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS MILI

7、TARY MIL-W-43334 STANDARDS FEDERAL - Packaging of Textile Webbing and Tape FED-STD-191 - Textile Test Methods FED-STD-595 - Colors MILITARY MIL-STD-105 - Sampling Procedure and Tables for Inspection by Attributes MIL-STD-129 - Marking for Shipment and Storage (Unless otherwise indicated, copies of f

8、ederal and military specification, standards, and handbooks are available from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, an

9、d publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. LAWS AND REGULATIONS RULES AND REGULATIONS UNDER THE TEXTILE FIBER PRODUCTS IDENTIFICATION ACT (Copies may be obtained without charge from the Feder

10、al Trade Commission, Washington, DC 20580). 2.2 Non-Government publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issue of documents which are DOD adopted shall be those listed in the issue of the DODISS cited in

11、the solicitation. Unless otherwise 2 d Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I ! i I i L L L L P P z MIL-W-17337F the issues of documents not listed in the DODISS shall be the issue of the documents cited in the solicitation. NATIONAL MOTOR

12、 FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Application for copies should be addressed to the American Trucking Association Inc., Traffic Department, 1616 P Street, NW, Washington, DC 20036.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification

13、(Application for copies should be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, ILL 60606). TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS Method No. 8-1988 Colorfastness to Crocking: AATCC Crockmeter Method (Applica

14、tion for copies should be addressed to the AATCC National Headquarters, P.O. Box 12215, Research Triangle Park, NC 27709-2215,) * 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothing

15、 in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Standard sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in th

16、e sample in which case this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Yarn. The yarn for the warp and filling shall be singles, bright, high tenacity, con

17、tinuous filament nylon, which has not been subjected to any type of bleaching process (see 4.4.1). For the class 1 webbing, only nylon 6,6 shall be used. For the class 2 webbing, either nylon. 6 or nylon 6,6 shall be used. 3.3.2 Yarn size. The yarn size shall be 840 denier (warp and filling) for shu

18、ttle loom construction and a combination of 840 denier warp and 420 denier filling for shuttleless loom construction (see 3.5.1 and 4.4.1). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-17337F 3.4 Color. Unless otherwise specified (see 6.2)

19、, the webbing shall be furnish- the following colors: a. Natural White b. Yellow No. 1365 Air Force Color c. Olive Drab Army Color No. 7 d. Deck Grey No. 26081 of FED-STD-595 3.4.1 Dyeing. When dyed webbing is required, the webbing shall be yarn or piece dyed. 3.4.2 Matching. The dyed webbing shall

20、match the standard sample when viewed under filtered tungsten lamps which approximate artificial daylight having a correlated color temperature of 7500 t 200 K, with illumination of 100 + 20 foot candles, and shall be a good matcii to the standard sample under incadescent lamplight at 2300 - t 200 K

21、. 3.4.3 Colorfastness. The dyed webbing shall show fastness to light, laundering, and crocking equal to or better than the standard sample when tested as specified in 4.5. As a limit of acceptability or when no standard sample is available, the dyed webbing shall show a minimum of rlgoodrl fastness

22、to light; rrfairrr fastness to laundering and shall have an AATCC reading not lower than 3.0 for dry crocking and an AATCC reading not lower than 2.0 for wet crocking. 3.5 Physical requirements. The construction and physical requirements of the finished webbing shall be as specified in Table I when

23、tested as specified in 4.5. The webbing-shall be furnished in the wid th as specified (see 6i2). TABLE I - CONSTRUCTION AND PHYSICAL REQUIREMENTS WIDTH THICKNESS WEIGHT/ BREAKING YARNS1 THREADS FULL WIDTH LINEAR STRENGTH INCH TOTAL WARP BINDER YARD WARP,FULL FILLING WARP ENDS ENDS (MAX) (MIN 1 (MIN)

24、 INCH INCH oz. LB S 1 (t 1/16) ,038 - a050 0.71 1200 48 1/ 119 97 22 1 172 (+ 1/16) .O38 - .O50 1.07 1800 48 T/ 179 145 34 2 (t 1/T6) ,038 - ,050 1.42 2200 48 f/ 239 193 46 3 (7 1/16) .O38 - ,050 2.20 3200 48 i/ - 355 287 68 I/ When a shuttleless loom is employed, 96 picks (two picks per shed) of 42

25、0 aenier yarn is required. 3.5.1 Catch-cord. When latch type shuttleless looms are utilized, the filling yarn shall traverse the full width of the webbing and shall be held by an extra catch-cord end interlacing with the filling yarn in a method as shown in figures 1 or 2. When bobbin type shut tlel

26、ess looms are utilized, interlacing of the catch-cord and filling shall occur within the first four 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-W-17337F 83 m 7777906 0346664 6 m MIL-W-17337F ends of warp yarn at the edge (see figure 3). F

27、or Class 2 webbing, dyed or natural, the catch-cord shall be 200 denier or 210 denier nylon for latch type shuttleless looms and 420 denier nylon for bobbin type shuttleless looms. 3.5.2 Curvature in shuttleless construction. Finished shuttleless webbing shall show no more lateral curvature than 1/4

28、 inch when tested as specified in 4.5. (see figure 4). 3.5.3 Weave. The weave shall consist of a face warp and back warp bound together by a binder warp and filling. The face warp shall weave plain with picks shown on the face and the back warp shall weave plain with picks that show on the back. The

29、 binder warp end shall be evenly spaced across the width of the webbing. One binder warp end shall weave 2 up and 2 down. The adjacent binder warp end shall weave 2 down and 2 up. Testing shall be in accordance with 4.5. 3.6 Non-fibrous materials. The chloroform soluble material only of the finished

30、 webbing shall not exceed 4.0 percen.t when tested as specified in 4.5. 3.7 pH. The pH value of the water extract of the finished webbing shall be not less than 5.0 nor more than 8.5 when tested as specified in 4.5. 3.8 Length of roll. Unless otherwise specified, each roll shall contain 90 to 110 ya

31、rds. No roil shall contain more than 2 pieces and no piece shall be less than 10 yards in length. 3.9 Identification ticket. Each roll of webbing shall have an identification ticket conforming to MIL-W-43334. 3.10 Fiber identification. Each roll of webbing shall be labeled or ticketed for fiber cont

32、ent in accordance with the Textile Fiber Products Identification Act (see 2.1.2). 3.11 Workmanship. The finished webbing shall conform to the quality established by this specification. The occurrence of defects shall not exceed the applicable levels. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibilit

33、y for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible for the performance of all inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or order, the contractor may use his own or any

34、 other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and serv

35、ices conform to prescribed requirements. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-W-L7337F 83 W 77797Ob OLLlbbb5 8 W MIL-W-17337F *4.1.1 Responsibility for compliance. All items must meet all requirements of sectioin set forth in this sp

36、ecification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to the Government for acceptance

37、 comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the govern

38、ment to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such i tems to determine the validity of the certification. 4.2 Classification of inspection. The inspection requirements specifi

39、ed herein are classified as follows: 1. First article inspection (see 4.3). 2. Quality conformance inspection (see 4.4). 4.3 First article inspection. When required, the first article submitted in accordance with 3.2, shall be inspected as specified in 4.4.2 for compliance with design, construction,

40、 workmanship, appearance and dimensional requirements. 4.4 Quality conformance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105, except where otherwise indicated. 4.4.1 Component and material inspect.ion. In accordance with 4.1 above, components and materials sha

41、ll be tested in accordance with all the requirements of referenced specifications, drawings, and standards unless otherwise excluded, amended, modified, or qualified in this specification or applicable procurement documents. 4.4.2 Examination of the end item. Examination of the end item shall be in

42、accordance with 4.4.2.1 through 4.4.2.4. 4.4.2.1 Length examination. The required length of each roll shall be examined on both sides and visual defects classified as listed in Table III. All defects found shall be counted, regardless of the proximity one to another, except where two or more defects

43、 represent a single local condition of the webbing, in which case only the more serious defect shall be counted. A continuous defect shall be counted as one defect for each warpwise yard or fraction thereof in which it occurs. The sample unit for this examination shall be one linear yard each. An ap

44、proximate equal number of yards shall be examined from each roll selected. The number of rolls from which the sample is to be selected shall be in accordance with Table II of this specification. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-flIL-

45、W-17337F 83 7977906 OL4bbbb T MIL-W-17337F TABLE II - sample size Lot Size in Yards Sample Size by Roll 1/. Max. number of defects 1200 or less 3 1201 to 3200 inclusive 5 3201 to 10,000 inclusive a 10,001 to 3500 inclusive 13 35,001 to 150,000 inclusive 20 150,001 and over 32 1/ If a lot contains le

46、ss than 3 rolls, each roll in the lot shall be examined. TABLE III - Classification of Defects Examine Defect Classification Major Minor 1. Abrasion mark(s) Any, resulting in rupture of individual yarns; distortion in the orientation of yarns; or areas visibly thinner than adjoining areas - 1/ 2. Br

47、oken or missing a. Two or more regardless of length warp end b. Single more than 1/4 inch in length 3. Broken or missing a. Two or more within a linear inch regardless of the size of missing port ion b. Single more than 1/4 inch in length 4. Cut , hole, tear Any 5. Course or heavy Noticeably stiffer

48、 or thicker filling bar than adjoining unaffected area - I! 6. Edge(s) 7. Ploat(s) a. Width of bar more than 1/4 inch b. Width of bar 1/4 inch or less Frayed, loopy, wavy, slack, noticeably thick or otherwise poorly constructed for a distance of 1 inch or more a. Multiple, in combined warp and filli

49、ng directions: 1. 1/2 inch or more 7 X X X X X X X X X Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Table III - Classification of Defects (contd) Examine Defect Classification Major Minor 8. Knot(s) 9. Slack end(s) 10. Tight end 11. Hitch-back 12. Crack or open place 13. Kinks 14. Mispick double 15, Slub, slug or jerked in filling 16. Spot, stain or 17. Smash 2. Less than 1/2 inch X b. Single