NAVY MIL-S-82183 A-1978 STRAINER ASSEMBLY PETROLEUM FUELS 6 INCH FRAME MOUNTED 600 GALLONS PER MINUTE《每分钟600加仑框架6英尺石油燃料过滤器组装》.pdf

《NAVY MIL-S-82183 A-1978 STRAINER ASSEMBLY PETROLEUM FUELS 6 INCH FRAME MOUNTED 600 GALLONS PER MINUTE《每分钟600加仑框架6英尺石油燃料过滤器组装》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-S-82183 A-1978 STRAINER ASSEMBLY PETROLEUM FUELS 6 INCH FRAME MOUNTED 600 GALLONS PER MINUTE《每分钟600加仑框架6英尺石油燃料过滤器组装》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、NIL-S-ZL83A 47 m 7377906 0257308 5 m T-T MIL - S - 8 2 18 3A (MC) 1 December 1978 SUPERSEDING 12 April 1968 MIL-S-82183 (MC) MILITARY SPECIFICATION STRAINER ASSEMBLY, PETROLEUM FUELS: 6-INCH, FRAME-MOUNTED, 600 GALLONS PER MINUTE This specification is approved for use by U.S. Marine Corps, Departmen

2、t of the Navy, and is available for use by all DepartmentS.and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers a 6-inch, parallel-flow, frame- mounted, 600-gallon-per-minute (gpm) strainer assembly. 2. APPLICABLE DOCUMENTS 2.1 Issues of documents. The following d

3、ocuments of the issue in effect on date of invitation for bids or request for proposal form a part of this specification %o the extent specified herein: Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be address

4、ed to: Corps, Code LMA-1, Washington, D.C. 20380 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by ietter. Commandant of the Marine Corps, Headquarters Marine FSC 4930 Licensed by Information Handling Services_ MIL-S-

5、ZLB3A 49 999990b 0257309 7 SPECIFICATIONS FEDERAL W-C-440 W-R-550 QQ-S-781 UU-P-268 Mbfil-A- 122 PPP- B-601 PPP-B-621 PPP-F- 320 PPP-P-40 MI LI TARY MIL-P-116 MIL-P- 514 MIL-T- 704 MIL-S-7916 MIL-W- 8604 MIL-A-8625 MIL- E- 52 798 MIL-V-58039 STANDARDS MI LI TARY MIL-STD- 105 MIL-STD- 129 MIL-STD- 13

6、0 MIL-STD-209 MIL-STD- 1186 - Clips, Electrical, General Specification - Rod, Ground (With Attachments). - Strapping, Steel, and Seals. - Paper, Kraft, Wrapping. - Adhesive, Butadiene Acrylonitrile Base, Medium Solids, General Purpose. - Boxes, Wood, Cleated-Plywood. - Boxes, Wood, Nailed and Lock-C

7、orner. - Fiberboard, Corrugated and Solid, Sheet - Packaging and Packing of Hand Tools. for. Stock (Container Grade), and Cut Shapes. - Preservation-Packaging, Methods of. - Plates, Identification, Instruction and Marking, Blank. - Treatment and Painting of Materiel. - Sealing Compound, Thread and G

8、asket, Fuel, Oil, and Water Resistant. - Welding of Aluminum Alloy: Process for. - Anodic Coatings, for Aluminum and Alumi- num Alloys. - Enamel, Alkyd, Camouflage. - Valves, Gate, Rising Stem, Double Acting, Aluminum. - Sampling Procedures and Tables for Inspection by Attributes. - Marking for Ship

9、ment and Storage. - Identification Marking of U.S. Military Property. - Slinging and Tiedown Provisions for Lifting and Tying Down Military Equipment. - Cushioning, Anchoring, Bracing, Blocking, and Waterproofing, with Appropriate Test Methods. 2 Licensed by Information Handling ServicesMIL-S-82283A

10、 LI9 m 379990b 0257LLO 3 MI L- S- 8 2 18 3A (MC) MIL-STD- 1188 - Commercial Packaging of Supplies and Equipment. MS2 70 2 3 - Coupling-Half, Quick Disconnect, Cam- Locking Type, Male, Flanged, Type IV. MS2 70 2 7 - Coupling Half, Quick Disconnect, Cam- Locking Type, Femaie, Flanged, Type VIII. MS270

11、28 - Coupling Half, Quick Disconnect, Cam- Locking Type, Cap, Dust, Type IX. MS27029 - Coupling Half, Quick Disconnect, Cam- Locking Type, Plug;, Duct, Type X. MS2 703 1 - Coupling Half, Quick Disconnect, Cam- Locking Type, Drilling Template. MS27183 - Washer, Flat-Round, Steel, Cadmium Piated, Gene

12、ral Purpose (in. /mm) . MS35338 - Washer, Lock-Spring, Helical, Regular (Medium) Serles, (in /mm) . MS39 336 - Y Connection, Quick Disconnect, Cam- Locking Type, Flange, Type XX. MS45904 - Washer, Lock, Internal and External Tooth MS5 196 7 - Nut, Plain, Hexagon- Cadmium Plated, U MS90725 - Screw, C

13、ap, Hexago It, Steel, Grade 5, Cadmium DRAWINGS U. S. MARINE CORPS 77C5 2 O 8A00 14 - Gasket. (Copies of specifications, standards, and drawings required by contrac- tors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contractin

14、g officer.) The following documents form a part of this 2.2 Other publications. specification to the extent specified herein. the issue in effect on the date of in proposal shall apply. Unless Othe AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) STANDARDS ASTM B 173 - Rope-Lay-Stranded Copper Cond

15、uctors Having Concentric- Stranded Members, for Electrical Conductors. - (Application for copies should be ad essed to the American Society for Testing and Materiah, 1916 Race Street, Philadelphia, PA 19103.) Licensed by Information Handling ServicesMIL- S- 82 18 38 (MC) (Technical society and techn

16、ical association specifications and stand- ards are generally available for reference from libraries. distributed among technical groups and using Federal agencies. ) They are also 3 . REQU IRHlENTS 3.1 First article. When specified (see 6.2.1), the contractor shall Eumish a sample unit(s) for first

17、 article inspection and approval (see 4.4 and 6.3). 3.2 Material. Material shall be as specified herein. Materials not specified shall be selected by the contractor and shall be subject to all provisions of this specification (see 6.4). 3.3 Design and construction. The strainer assembly shall be as

18、speci- fied herein and shall consist of one coupling half dust plug, one flanged female coupling half, two Y-fittings, four gate valves, four pipe elbows, two sediment strainers, one flanged male coupling half, one coupling half dust cap, one ground rod, one ground wire assembly, frame, flange gaske

19、ts, and threaded fasteners. Components, less frame, shall be arranged as shown in Figures 1 and 2 to provide parallel flow. 3.3.1 Couplinghalf dust plug. The coupling half dust plug shall conform to MS2 7029- 19. 3,J.Z Flanged female coupling half. The flanged female coupling half shall conform to M

20、S27027-19. 3.3.3 Y-fitting. The Y-fitting shall conform to MS39336-5. 3.3.4 Gate valve. The gate valve shall conform to MIL-V-58039, size 6-inch, type I. 3.3.5 Pipe el-bow. The pipe elbow shall be a 45-degree, flanged, 4.7.1,3 Examination. Samples selected in accordance with 4.7.1.2 shall be examine

21、d for the following major defects. percent defective. AQL shall be 2.5 111. Strainer gaskets not protected as specified for level A. 112. Strainer assembly not preserved as specified for level A. 113. Technical publications not preserved as specified for 114. Maintenance tools not preserved in accor

22、dance with refer- 115, Repair parts not preserved as specified for level A. 116, Exterior containers not as specified for level A or B. 117. Blocking, bracing, and anchoring not as specified for 118. Commercial packaging not as specified. 119. Marking illegible, incorrect, or incomplete. level A. en

23、ced document for level A. level A or B, 5. PACKAGING 5,l Preservation. Preservation shall be level A or commercial, as specified (see 6.2, i). 5,1,1 Level A. 5.1.1.1 Strainer gaskets. The spare strainer gaskets shall be inter- leaved with paper conforming to UU-P-268 and placed between two sheets of

24、 fiberboard conforming to PPP-F-320, type, class, variety and grade optional, 1/2 inch beyond the gasket edges. The fiberboard shall be of such a size as to extend at least 5.1.1,2 Strainer assembly. The interior surfaces of the strainer assembly requiring a preservative in accordance with MIL-P-116

25、 shall be coated with P-10, type I, grade 30 preservative as specified in MIL-P-116. The valves shall be left open a minimum of 1/4 inch and the dust caps and plugs installed. be preserved in accordance with MIL-P-116, method IC-1 or IC-3, accordance with the level A requirements of PPP-P-40. 5 1 ,

26、1.3 Technical publications. Technical publications provided shall 5.1.1.4 Maintenance tools. Maintenance tools shall be preserved in 5,1,1.5 Repair parts, Repair parts shall preserved in accordance with the applicable criteria of MIL-P-116. 12 3 Licensed by Information Handling ServicesMIL- S - 8 2

27、18 3A (MC) 5.1.2 Commerical. The complete strainer assembly shall be preserved in accordance with MIL-STD-1188. 5.2 Packing. Packing shall be level A, B, or commercial, as specified (see 6.2.1). 5.2.1 Level A. Each complete strainer assembly shall be packed in a box conforming to PPP-B-601, overseas

28、 type, grade B, or PPP-B-621, class 2. Blocking, bracing, and anchoring of the contents shall be in accord- ance with MIL-STD-1186, QQ-C-781, class 1, type I or IV, size as applicable and unless otherwise specified shali be finish B (see 6.2.1). When specified, strapping shall be finish A (see 6.2.1

29、). 5.2,2 Level B. Required strapping shall be in accordance with Each complete strainer assembly shall be packed as specified for level A except the boxes shall be domestic type. ping shall be either finish A or B. Strap- 5.2.3 Commercial. Each strainer with the required technical publi- cations, re

30、pair parts, and maintenance tools shall be packed in accord- ance with MIL-STD-1188. 5.3 Marking. In addition to any special marking required by the contract, unit packages, intermediate- packages, and shipping containers shall be marked in accordance with the requirements of MIL-STD-129. 6. NOTES 6

31、.1 Intended use. The strainer assembly is intended for use in removing solid contaminants from liquid petroleum fuels. assembly is a component of an amphibious fuel system that receives, stores, transfers, and dispenses gasoline, diesel fuel, and jet fuel. The strainer 6.2 Ordering data. Procurement

32、 documents should specify the following: 6.2.1 Procurement requirements. a. Title, number, and date of this specification, b. c. When instruction plate is not required (see 3.703). d. e. When finish A strapping is required (see 5.2.1). When a first article is required for inspection and approval (se

33、e 3.1, 4.4, and 6.3). Level of preservation and packing required (see 5.1 and 5.2). 6.2.2 Data requirements. When this specification is used in a pro- curement which incorporates a Contract Data Requirements List (DD Form 1423) and invokes the provisions of 7-104.9(n) of the Armed Services 13 Licens

34、ed by Information Handling ServicesMIL- S-8218 3A (MC) Procurement Regulations, the data requirements identified below will be developed as specified by an approved Data Item Description (DID) (DD Form 1664) and delivered in accordance with tlie approved DD Form 1423 incorporated into the contract.

35、When the provisions of ASPR-7-104.9(n) are not invoked, the data specified below will be delivered by the contractor in accordance with the contract requirements. Deliverable data required by this specification is cited in the following paragraphs: Paragraph Data requirement Applicable DID 4.4 First

36、 Article Inspection Procedures. DI -T- 490 1 4.4 First Article Inspection Report. D I-T- 4902 4.5 Production/Acceptance Inspection DI-T- 4903 4.6 Inspection System Program Plan. DI -R- 480 3 4.6 D I - R- 48 O9 Procedures. . End Item Final Inspection Record. (Copies of Data Item Descriptions required

37、 by contractors in connec- tion with specific procurement. functions should be obtained from the procuring activity or as directed by the contracting officer.) tested and approved under the appropriate provisions of 7-104.55 of the Armed Services Procurement Regulation. The first article should be t

38、he first-produced item. assembly. The contracting officer should include specific instructions in all procurement instruments, regarding arrangements for examinations, test, and approval of the first article (see 3.1 and 6.2.1). 6.4 Recycled material. It is encouraged that recycled or reclaimed mate

39、rial be used, when practical, as long as it meets the requirements of this specification (see 3.2). 6.3 First article. When a first article is required it shall be The first article should consist of one strainer 6.5 Changes from previous issue. Asterisks are not used in this re- vision to identify

40、changes with respect to the previous issue, due to the extensiveness- of the changes. Preparing activity : Project 4930-N216 Navy-MC 14 Licensed by Information Handling ServicesLicensed by Information Handling Servicess Y o 8 I- h n U w U Y I I iJ 16 Licensed by Information Handling Servicesx P v) v) d a) k er( B a F: 7 O k U 4 ?3 M w d 3 U H cr, 17 Licensed by Information Handling Services