NAVY MIL-S-23965 (1)-1988 SHORES DAMAGE CONTROL AUTOMATIC ADJUSTABLE TELESCOPING STEEL《自动的可调式伸缩钢损害控制装置》.pdf

《NAVY MIL-S-23965 (1)-1988 SHORES DAMAGE CONTROL AUTOMATIC ADJUSTABLE TELESCOPING STEEL《自动的可调式伸缩钢损害控制装置》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-S-23965 (1)-1988 SHORES DAMAGE CONTROL AUTOMATIC ADJUSTABLE TELESCOPING STEEL《自动的可调式伸缩钢损害控制装置》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-23965 (3) 20 W 9999906 0392776 5 k-;3 9Y- MIL-S-23965(SHPS) AMENDMENT 1 i July 1988 MILITARY SPECIFICATION SHORES, DAMAGE CONTROL, AUTOMATIC, ADJUSTABLE TELESCOPING STEEL This amendment forms a part of MIL-S-23965(SHIPS), dated 20 January 1964, and is approved for use within the Naval Sea Syst

2、ems Command, Department of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 2.1, under SPECIFICATIONS, FEDERAL: Delete “QQ-Z-325 - Zinc Coating, Electro- deposited, Requirements for.“ and substitut.e “TT-P-645 - Primer, .:Paint, Zinc Chromate, A

3、lkyd Type.“ 2.1, under SPECIFICATIONS, MILITARY: Delete “MIL-P-8585 - Primer Coatings, Zinc-Chromate, Low-Moisture-Sensitivity.“ and MIL-P-15328 - Coating, Pretreatment (Formula No. 117 for Metals).“ and substitute “DOD-P-15328 - Primer(Wash), Pre- treatment (Formula No. 117 for Metals) (Metric).“ 3

4、.2.3.1: Delete and substitute: “3.2.3.1 Priming. Each metal part shall be primed in accordance with the best commercial practice. One coat of pretreatment primer in accordance with DOD-P-15328 and one coat of zinc chromate primer in accordance with TT-P-645, formula 84, shall be applied to the insid

5、e and outside of the inner and outer tubes, in addition to all other fixed and moving parts.“ msc NIA FSC 2090 DISTRIBUTION STATEMENT A Approved or public release; distribution unlimited 1 of 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-23

6、965 (1) 20 W 977790b 01172777 7 W MIL-S-23965(SHIPS) AMENDMENT 1 PAGE 3 3.3.10: Delete and substitute: “3.3.10 Design. The shore shall consist of two telescoping square tubes with slots on the four sides of the inner tube, four spring loaded locking devices on the outer tube, swivel base plate on on

7、e end of the inner tube, and swivel base plate and screw jack on the outer tube. device shall be provided to prevent the slippage of the inner tube of one inch or more in relation to the outer tube while the shoring 2s held vertically in its closed position. parts, otherwise there shall be no loose

8、parts.“ A spring loaded locking The entire shore shall consist of only two separable PAGE 4 TABLE I, under “Category, Major“: Add “109“ TABLE I, under “Defects“, opposite “109“: IJ Add “Inner tube slippage of an inch or more when the shore is held vertically in its closed position.“ Preparing activity: Navy - SH (Project 2090-N099) Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-