NAVY MIL-S-12227 F-1989 SUIT TOXICOLOGICAL AGENTS PROTECTIVE COVER COOLING《用于毒物性学保护和冷却的套装》.pdf

《NAVY MIL-S-12227 F-1989 SUIT TOXICOLOGICAL AGENTS PROTECTIVE COVER COOLING《用于毒物性学保护和冷却的套装》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-S-12227 F-1989 SUIT TOXICOLOGICAL AGENTS PROTECTIVE COVER COOLING《用于毒物性学保护和冷却的套装》.pdf（36页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-S-32227F 84 W 977790b O378376 2 m INCH-POUND MIL-S-12227F May 8, 1989 SUPERSEDING 4 September 1980 MIL-S-12227E MILITARY SPECIFICATION SUIT, TOXICOLOGICAL AGENTS PROTECTIVE COVER, COOLING This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOP

2、E 1.1 Scope. This specification covers the requirements for a two-piece cotton birdseye cloth cooling suit comprised of a jacket and trousers. 1.2 Classification. The suit shall be of one type and one size in the following items (see 6.2): Item 1 - Suit, Cooling, Jacket Item 2 - Suit, Cooling, Trous

3、ers 2. APPLICABLE DOCUMENTS 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those li

4、sted in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addre

5、ssed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmore Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC N/A FSC 8415 DISTRIBUTION STATEMENT A.

6、Approved for public release, distribution is unlimi ted. f THIS DOCUMENT ONTAINS 3s PAGES. - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_ MIL-S-12227F 8L( W 7977706 0378377 i.I W MIL-S-12227F SPECIFICATIONS FEDERAL V-T-276 * NN-P-71 ccc-c-425 D

7、DD-L- 2 O DDD-T-86 MILITARY MIL-W-530 MIL-B-543 * MIL-P-15011 . MIL-F-10884 MIL-B-17757 * MIL-T-43548 STANDARDS FEDERAL FED-STD-751 MILITARY MIL-STD-105 MIL-STD-129 * MIL-STD-147 * MIL-STD-2073-1 * MIL-STD-2073-2 - Thread, Cotton - Pallet, Material Handling, Wood, Stringer - Cloth, Birdseye and Gauz

8、e; Cotton. - Label; for Clothing, Equipage, and Tentage (General - Tape, Textile; Cotton, General Purpose (Unbleached, Construction, 2 Way and 4 Way (Partial) Use) Bleached, or Dyed) E - Webbing, Textile, Cotton, General Purpose, Natural - Buckles, Tongueless and Web Strap - Fasteners, Snap - Pallet

9、, Material Handling, Wood, Post Construction, - Boxes, Fiberboard, Corrugated (Modular Sizes) - Thread, Polyester Core: Cotton-, Rayon-, or or in Colors D 4 Way Entry Polyester-Covered - Stitches, Seams, and Stitchings - Sampling Procedures and Tables for Inspection by - Marking for Shipment and Sto

10、rage - Palletized Unit Loads - Department of Defense Materials Procedures for Development and Applications of Packaging Requirements Attributes - Packaging Requirement Codes (Unless otherwise indicated, copies of federal and military specifications, standards, and handbooks are available from the Na

11、val Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless ot

12、herwise specified, the issues are those cited in the solicitation. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-L2227F L( M 7977706 0378378 b MIL-S-12227F U.S. POSTAL SERVICE MANUAL (Copies of the manual may be obtained from the Superinten

13、dent of Documents, U,S, Government Printing Office, Washington, DC 20402-0001) * 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed

14、 in the issue of the DODISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Appl

15、ication for copies should be addressed to the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404). UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Application for copies should be addressed to the Uniform Classification Com

16、mittee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808). TECHNICAL MANUAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS Method No. IA, T.M. 61-1980 (Application for copies should be addressed to AATCC National Headquarters, P.O. Box 12215, Research Triangle Park,

17、NC 27709-2215) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute the documents. These documents also may be available in or through libraries or other informational services.) * 2.3 Order of precedence. In the event of a conflic

18、t between the text of this document and the references cited herein, the text of this document shall take precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished

19、, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-3.2 unit( First articl

20、e. MIL-S-12227F When specified, the contractor shall furnish sample *a ) for first arti le inspection and approval (see 4.3 and 6.2). 3.3 Material. (See 6.4). * 3.3.1 Basic material. The basic material for the jacket and trousers shall be cotton birdseye cloth, approximately olive green shade No. 10

21、7, conforming to Type I, class 3 of CCC-C-425, except the weight per square yard shall be 3.7 oz. min; the residual shrinkage shall not exceed 10 percent in either the warp or filling directions; and the minimum absorption shall be 50 percent. * 3.3.1.1 Colorfastness. The colorfastness requirement s

22、hall be colorfastness to laundering (after 3 cycles), perspiration and crocking. Colorfastness to laundering shall be in accordance with AATCC T.M.61-1980, L Method IA. Samples shall be dried after each complete laundering cycle and only the stain on the cotton fibers of the transfer cloth shall be

23、evaluated. z 3.3.2 Tape, cotton. The tape for leg tie cords shall be cotton herringbone twill weave, 1/2 inch wide, olive green shade No. 107, conforming to type I, class 3 of DDD-T-86, except the only colorfastness requirement shall be colorfastness to laundering. 3.3.3 Webbing, cotton. The webbing

24、 for the waist adjustment straps shall be cotton, 5/8 inch wide, olive drab shade No. 7, conforming to type II or type IIa, class 3 of MIL-W-530, except the only colorfastness requirement shall be colorfastness to laundering. * 3.3.4 Thread. The thread for seaming and stitching shall be cotton, tick

25、et No. 50, 2 or 3 ply and ticket No. 70, 2 ply conforming to type IA3 of V-T-276. As an alternate, either cotton-covered or rayon-covered polyester thread, ticket No. 50, 3 ply and ticket No. 70, 2 ply, conforming to MIL-T-43548 may be substituted for the cotton thread. The color shall approximate t

26、he basic material and be uniform throughout the garment. 3.3.4.1 Colorfastness. The dyed thread shall show fastness to laundering equal to or better than the standard sample. As a limit of acceptability, or when no standard sample is available, the dyed thread shall show good fastness to laundering.

27、 * 3.3.5 Label. Each jacket and trouser shall have a combination identification and instruction label conforming to type I, class 15 of DDD-L-20. The printing shall show fastness to laundering. The label shall bear the following inscription: 4 Provided by IHSNot for ResaleNo reproduction or networki

28、ng permitted without license from IHS-,-,-MIL-S-12227F 8L( 7777906 0378180 4 MIL-S-12227F SUIT, TOXICOLOGICAL AGENTS PROTECTIVE COVER, COOLING BASE FABRIC: 100% COTTON CONTRACT NO: DLA 100-00-0-0000 (EXAMPLE) NAME OF CONTRACTOR: NAME OF MANUFACTURER: (If other than contractor) STOCK NO. 8415-00-000-

29、0000 (EXAMPLE) INSTRUCTIONS 1. Wear over impermeable type suit for reduction of body heat stress. 2. Keep soaked with water for maximum evaporative cooling effect. 3. Wear legs outside of footwear. 4. After use, rinse suit thoroughly and hang up to dry. LAUNDRY INSTRUCTIONS Hand Wash Cold Hang Dry D

30、O NOT REMOVE THIS LABEL 3.3.6 Buckles, tongueless. The buckles for the waist adjustment straps shall be tongueless, 2-bar, 518 inch, conforming to type II, style 4, class 1, 3, or 4, construction B of MIL-B-543. 3.3.7 Buckles, slide. The slide buckles for the suspender adjustment shall be buckles, c

31、enter bar slide, 1-1/4 inch, conforming to type III, style 3, class 1, 3, or 4, construction A of MIL-B-543. 3.3.8 Fasteners, snap. The snap fasteners for attaching the suspenders to the trousers shall be style 2A, finish 2, brass, male and female complete, conforming to MIL-F-10884. 3.4 Design. The

32、 jacket is a loose fitting, slip-on type, with long sleeves and back tie belt. The trouser is a loose fitting slip-on type, with attached suspenders, waist adjustment straps, and leg tie tapes (see Figuire 1). 3.4.1 Figure. The figure is furnished for information purposes only. When inconsistencies

33、exist between the written specification and the figure, the written specification shall govern. * 3.5 Patterns. Standard patterns to be used to cut working patterns will be furnished by the Government (see 6.3). The working patterns shall be identical to the Government patterns. Neither the Governme

34、nt patterns nor the working patterns shall be altered in any way, except that additional notches for use during construction are permitted on the working patterns. Also, minor modifications are permitted where necessary when using automatic equipment. These modifications shall not alter the dimensio

35、nal, serviceability, or appearance requirements cited in the specification. The patterns provide a seam allowance of 3/8 inch for single needle and 1/2 inch for double needle seams. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-S-12227F 8L( m 9

36、977906 0378181 b m MIL-S-12227F * 3.5.1 Pattern parts. The component parts shall be cut from the material specified in accordance with the following pattern parts: 0 Ma terials Nomenclature of pattern parts Cut parts Basic material Jacket Back 1/ Fron t-2/ Sleeve- Front facing Neck facing Tie belt T

37、rouser Back Front Suspender strap 3/ Suspender adj us tient strap - 31 Waist facing 2 - 1/ A four piece back may be used to accommodate cloth in widths less than 29 inches. Additional seam allowance is required to meet. jacket dimensions stated in Table II. - 2/ To accommodate cloth in widths less t

38、han 29 inches, the front shall be cut with a sewn-on facing in lieu of the grown-on type reflected on the pattern. Additional seam allowance is required to meet jacket dimensions stated in Table II. - 3/ A 2 piece suspender strap or suspender adjustment strap may be used to accommodate a special two

39、 (2) needle banding machine as listed in Table I, operation 21e. Additional seam allowances are required to meet suspender strap and suspender adjustment strap dimensions stated in Table I. o. 3.6 Construction. * 3.6.1 Stitches, seams, and stitching. Stitch, seam, and stitching types specified in Ta

40、ble I shall conform to the requirements of FED-STD-751. Whenever two or more methods for seam or stitch types are given for the same part of the operation, any one may be used Where stitch type 401 is used, the looper (underthread) shall be on the inside of the garment. Ends of all seams produced by

41、 stitch type 401 shall be caught in other seams or stitching. The bight of overedge stitching shall be 3/16 inch. The guide and knife shall be set to trim only the ravelled ends of the fabric. Unless otherwise specified, all double needled stitching shall be double lapped. The double needle stitchin

42、g shall be 1/4 (+ 1/16) inch gauge, with the outer row of stitching 1/16 to 1/8 inch from fiished edge. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- flIL-S-L2227F 8L( m 7797706 0378182 8 m MIL-S-12227F * 3.6.2 Thread breaks and ends of seams. E

43、nds of all seams and stitchings when not caught in other seams or stitchings shall be backtacked not less than 3/8 inch. The ends of a continuous line of stitching (except label) shall be overlapped not less than 1/2 inch. The ends of the label stitching shall be overlapped not less than 3 stitches.

44、 Thread breaks (all stitch types) shall be secured by stitching back of break not less than 1/2 inch. Skipped stitches or thread breaks on 401 seaming may be repaired by using 301 stitch type. When ends of overedge stitching are not caught in other seams or stitching, the ends shall be tacked or ext

45、end 1/4 to 3/8 inch. 3.6.3 Stitches per inch. The minimum and maximum number of stitches shall be as specified in Table I. * 3.7 Manufacturing operations requirements. The suit (jacket and trousers) shall be manufactured in accordance with operation requirements as specified in Table I. The contract

46、or is not required to follow the exact sequence of operations provided the finished suit (jacket and trousers) is identical to that produced by following the sequence listed in Table I. Minor modifications are permitted where necessary when using automatic equipment. These modifications shall not al

47、ter the dimensional, serviceability, or appearance requirements cited in the specification. * 3.7.1 Abbreviations in table of operations. The abbreviations used in Table I are as follows: Stch - in - Ndl - Bob - LPr Mchne - Brtck - Comrcl - smlr - Btnhl - incl - dbl - chnstch - - Stitch inch Needle

48、Bobbin Looper Machine Bar tack Commercial similar Buttonhole including double chainstitch 7 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NO. - NIL-S-LZ227F 4 7977706 0378383 T MIL-S-12227F TABLE I - CONSTRUCTION OF SUIT OPERATION *1. Cutting suit.

49、 a. The suit (jacket and trousers) shall be cut in accordance with patterns furnished which show notches for proper assembling and directional lines for laying of patterns. To accommodate cloth in widths less than 29 inches, the back shall be cut in two pieces and the front shall be cut with a sewn-on facing in lieu of the grown-on type reflected in the pattern. Additional seam allowance is required so jacket will finish to dimension