NAVY MIL-R-85535-1983 RECORDER-REPRODUCER SET DIGITAL DATA AN ASH-33《AN ASH-33型数字数据收发双用机设备》.pdf

《NAVY MIL-R-85535-1983 RECORDER-REPRODUCER SET DIGITAL DATA AN ASH-33《AN ASH-33型数字数据收发双用机设备》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-R-85535-1983 RECORDER-REPRODUCER SET DIGITAL DATA AN ASH-33《AN ASH-33型数字数据收发双用机设备》.pdf（115页珍藏版）》请在麦多课文档分享上搜索。

1、. - -. - - - - -_ MIL-R-85535 58 9799706 0375580 2 W MI L-R-85535( AS) 8 June 1983 MILITARY SPECIFICATION RECORDER - REPRODUCER SET, DIGITAL DATA, AN/ASH-33 This specification is approved for use by The Naval Air Systems Command, Department of The Navy, and is available for use by all Departments an

2、d Agencies of The Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the design, construction, testing, performance, digital protocol and digital format requirements for the Recorder-Reproducer Set, Digital Data, AN/ASH-33, herein referred to as the Digital Magnetic Tape Set (DMTS)

3、. subunits (WRAS) : The DMTS consists of the following Control, Magnetic Tape, C-10553/ASH-33 (DMTC) Quantity Per Set 1 Recorder-Reproducer, Digital Data, 1 to 4 RD-450/ASH-33 (DMTU) The DMTU operates with a magnetic tape cartridge. The DMTS provides computer controlled program load and auxiliary bu

4、lk storage memory for the AN/USQ-78(V) Display and Control System (DCS), the AN/ASQ-114, Computer Set, Digital (CP-gol), and the AN/AYK-l14(V) Computer Set, Standard Airborne. Beneficial comments (recommendations, additions, deletions) , any pertinent data which may be of use in improving this docum

5、ent should be addressed to: Commanding Officer, Naval Air Engineering Center, Engineering Specifications and Standards Department (ESSD) , Code 93, Lakehurst, NJ 08733, by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or b

6、y letter. THIS DOCUMENT CONTAINS /)5 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-R-5535 58 7777906 0175581 i.I MIL-R-85535 (AS) When configured to interface with only the AN/ASQ-114, Computer Set, Digital (CP-901) , the nomenclature s

7、hall be: N/ASH-33, Recorder-Reproducer Set , Digital Data consisting of: C-10553/ASH-33 Control, Magnetic Tape R D-4 50/AS H-33 Recorder-Reproducer, Digital Data When configured to interface with the CP-901 and the AN/USQ-78(V), Display and Control System (DCS) , the nomencl ature shall be: AN/ASH-3

8、3AY Recorder-Reproducer Set, Digital Data consisting of: C-10553A/ASH-33 Control, Magnetic Tape RD-450/ASH-33 Recorder-Reproducer, Digital Data Configured to interface with the CP-901, the DCS, and the AN/AYK-l4(V) Computer Set, Standard Airborne the nomenclature shall be: AN/ASH-33( ), Recorder-Rep

9、roducer Set, Digital Data consisting of the: C-10553( )/ASH-33 Control , Magnetic Tape RD-450/ASH-33 Recorder-Reproducer, Digital Data 1.2 Associated equipment. This equipment operates in conjunction with 2. APPLICABLE DOCUMENTS the associated equipment listed in 6.8. . 2.1 Government documents. 2.1

10、.1 Specifications, standards and handbooks. Unless otherwise specified (see 6.4) , the following specifications, standards and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications and Standards (DoDISS) specified in the solicitation, form a part of this sp

11、ecification to the extent specified herein. SPECIFICATIONS M I L ITARY MIL-C-5 MIL-C-62 Capacitors, Fixed, Mica Dielectric, General Specification for Capacitor, Fixed, Electrolytic (DC, Aluminum, Dry Electrolyte, Polarized) , General Specification for Preservation, Methods of a ? 1 3 MIL-P-116 2 Pro

12、vided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-1 MIL-R-5535 58 777370b 0375582 b m . DoD-D-1000 MIL-C-3965 MIL-B-5087 MIL-W-5088 MIL-E-5400 MIL-T-5422 MIL-C-5541 MIL-E-5558 MIL-R-5757 MI L-C-6781 MIL-M-7793 MIL-1-8500 MIL-C-14409 MIL-E-1 7555 MIL-M-180

13、12 MIL-N-18307 MIL-S-19500 MI L-B-23071 MIL-C-23269 MIL-C-25050 MIL-P-28809 MIL-M-38510 Drawings, Engineering and Associated Lists Capacitor, Fixed, Electrolytic (Nonsolid Electrolyte), Tantalum, General Specification for Bonding, Electrical, and Lighting Protection, for Aerospace Systems Wiring, Ae

14、rospace Vehicle Electronic Equipment, Aerospace, General Specification for Testing, Environmental, Aircraft Electronic Equ i pmen t Chemical Conversi on Coat i ngs on Al umi num and Aluminum Alloys . Enamel, Wrinkle-Finish, for Aircraft Use Re1 ay, Electromagnet i c, General Speci f i cat i on for C

15、ontrol Panel, Aircraft Equipment, Rack or Console Mounted (ASG) Meter, Time Totalizing Interchangeability and Replaceability of Component Parts for Aircraft and Missiles Capacitors, Variable (Piston Type, Tubular Trimmer) , General Specification for Electronic and Electrical Equipment, Accessories,

16、and Repair Parts, Packaging and Packing of Markings for Aircrew Station Displays, Design and Configuration of Nomenclature and Identification for Electronic, Aeronautical , and Aeronautical Support Equipment, Including Ground Support Equipment Semiconductor Device, General Specification for Blower,

17、Miniature, for Cooling Electronic Equipment, General Specification for Capacitors, Fixed, Glass Dielectric, Established Reliability, General Specification for Color, Aeronautical Lights and Lighting Equipment , General Requirements for (ASG) Printed Wiring Assemblies Microcircuits, General Specifica

18、tion for 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-R-85535 58 W 7777706 0375583 8 m MI L-C-38999 MI L-C-39001 MIL-C-39003 MIL-C-39006 MIL-C-39006/22 MIL-R-39007 MIL-R-39008 MI L-C-39014 MI L-R-39016 MIL-H-46855 MI L-R-55182 MI L-C-83421

19、STANDARDS FEDERAL FED-STD-595 MIL ITARY MI L-STD-198 MIL -R-8 5535 (AS) Connectors, Electrical , Circular, Miniature, High Density, Quick Disconnect, Environment Resistant, Removable Crimp and Hermetic Solder Contacts, General Specification for Capacitors, Fixed, Mica Dielectric, Established Re1 iab

20、il ity, General Specification for Capacitors, Fixed, Electrolytic (Solid Electrolyte) , Tantalum, Establ ished Reliability, General Specification for Capacitors, Fixed, Electrolytic (Nonsolid Electrolyte), Tantalum, Established Reliability, General Specification for Capacitor, Fixed, Electrolytic (N

21、onsolid Electrolyte) , Tantalum, (Polarized, Sintered Slug), 85 Deg C (Voltage Derated to 125 Deg C), Established Reliability, Style CLR79 Resistors, Fixed, Wirewound (Power Type), Established Reliability, General Specification for Resistors, Fixed, Composition (Insulated), Established Reliability,

22、General Specification for Capacitors, Fixed, Ceramic Dielectric (General Purpose), Established Reliability, General Specification for Relays, Electromagnetic, Established Reliability, General Specification for Human Engineering Requirements for Military Systems, Equipment and Facilities Resistors, F

23、ixed, Film, Established Reliability, General Specification for Capacitors, Fixed, Supermetallized, Plastic Film Dielectric (DC, AC, or DC and AC), Hermetically Sealed in Metal Cases, Established Reliability, General Specification for Colors Capacitors, Selection and Use of 4 Provided by IHSNot for R

24、esaleNo reproduction or networking permitted without license from IHS-,-,-MIL-STD-210 MIL-STD-454 MIL-STD-461 MIL-STD-462 MIL-STD-463 I MIL-STD-470 MIL-STD-471 MIL-STO-704 MIL-STD-740 MIL-STD-756 MI L-STD-781 MIL-STD-785 MIL-STD-794 MIL-STD-810 MIL-STD-883 MIL-STD-965 MIL-STD-1397 MIL-STD-1472 MIL-S

25、TD-1553 MIL-R-85535 58 97999Ob OT7558LI T = Climatic Extremes for Military Equipment Standard General Requirements for Electronic Equipment El ectroni c Emi ssi on and Suscept i bi 1 i ty Requirements for the Control Electromagnetic Interference Electromagnetic Interference Characteristics Measureme

26、nt of Definitions and System of Units, Electromagnetic Interference Technology Maintainability Program Requirements (for Systems and Equipment) Maintainabi 1 ity Demonstration Aircraft Electric Power Characteristics Airborne and Structureborne Noise Measurements and Acceptance Criteria of Shipboard

27、Equipment Reliability Modeling and Prediction Reliability Test Exponential Distribution Reliability Program for Systems and Equipment Development and Production Parts and Equipment, Procedures for Packaging of Environmental Test Methods Test Methods and Procedures for Microelectronics Parts Control

28、Program Input/Output Interfaces, Standard Digital Data, Navy Systems Human Engineering Design Criteria for Military Systems, Equipment and Facilities Aircraft Internal Time Division Command/Response Multiplex Data Bus MIL-STD-1562 Lists of Standard Microcircuits 5 Provided by IHSNot for ResaleNo rep

29、roduction or networking permitted without license from IHS-,-,-MIL-STD-1635 MIL-STD-1679 Weapon System Software Development Re1 i abi 1 i ty Growth Test i ng MIL-STD-2068 Re1 i abi 1 i ty Development Tests MIL-STD-2074 Fai lure C1 assif ication for Re1 i abi 1 i ty Testing MIL-STD-2084 General Requi

30、rements for Maintainability of Avionic and Electronic Systems and Equipment MS 17321 MS 17322 Meter, Time Totalizing, Miniature, Digital 28 Volt DC Meter, Time Totalizing, Miniature, Digital, 115 Volt, 400 Hertz HANDBOOKS MILITARY MIL-HDBK-217 Reliability Prediction of Electronic Equipment MIL-HDBK-

31、472 Maintainability Prediction 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. OTHER GOVERNMENT DOCUMENTS DEPARTMENT OF THE NAVY SECNAVINST 3560.1 Tact

32、ical Data Systems Documentation Standards NAVAL AIR SYSTEMS COMMAND NADC Proteus/LAB 007 Proteus Digital Channel (PDC), Device Interface Description of NADC Sink Logic NADC Proteus/LAB 008 Proteus Digital Channel (PDC) Theory of Operation of NADC Sink Logic NADC Proteus/LAB O1 3 Proteus Digital Chan

33、nel (PDC), Device Interface Description of NADC Source Logic NADC Proteus/LAB 015 Proteus Digital Channel (PDC) Theory of Operation of NADC Source Logic AR-1 06 Commonality of Digital Computer Hardware and Programming Language within Weapon Systems, Requirements for J 6 Provided by IHSNot for Resale

34、No reproduction or networking permitted without license from IHS-,-,-. MIL-R-85535 58 m 9777306 0175586 3 W MI L - R-8 55 3 5 (AS ) EI-680 AD-1 350 AD-1404 Avionics Installation Instructions for Recorder-Reproducer Set, Digital Data Engineering Drawings and Associated Data Interface Design Specifica

35、tion (IDS) Dig ta Recorder-Reproducer Set AN/ASH-33 for P-3C UPDATE III Aircraft Equipment AN/ASH-33 AS-461 3 A30-15590 NATIONAL SECURITY AGENCY NACSEM 5100 Application and Derating Requirements for Electronics Components, General Specification for Proteus Digital Channel Compromising Emanations Lab

36、oratory Test Standard Electromagnetics (U) PUBLICATIONS NAVAL ELECTRONIC SYSTEMS COMMAND, THERMAL TECHNOLOGY LABORATORY 0967-437-7010 NAVELEX Reliability Design Vol 1-4 Handbook, Thermal Appl i cat ions (Copies of specifications, standards, handbooks, drawings and publications required by manufactur

37、ers in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting officer.) specification to the extent specified herein. which are indicated as DoD adopted shall be the issue listed in the current DoDISS and the supplement there

38、to, if applicable. 2.2 Other publications. The following documents form a part of this The issues of the documents AMERICAN SOCIETY OF MECHANICAL ENGINEERS ANSI X 3.39-1973 American National Standard, Recorded Magnetic Tape for Information Exchange (1600 CPI, PE) (Application for copies should be ad

39、dressed to the American Society of Mechanical Engineers, 345 East 47th Street, New York, NY 10017.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. 7 Provided by IHSNot f

40、or ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-R-85535 58 M 7797706 0375587 5 W MIL -R-85535 (AS) 3. REQUIREMENTS 3.1 First article inspection. When specified, a sample shall be subjected to first article inspection (see 4.3 and 6.3). 3.2 Parts and materials. In t

41、he selection of parts and materials, fulfillment of major design objectives shall be the prime consideration. The requirements of MIL-STD-965 shall apply (see 6.2.2). following shall govern: In so doing, the a. Microelectronic technology shall be considered and microelectronic items shall conform to

42、 requirements specified herein. b. Other parts and materials requirements shall conform to MIL-E-5400. c. Nonrepairable subassemblies shall be used in accordance with MIL-STD-2084 and as outlined in MIL-E-5400. d. When previously produced models of this equipment did not use nonrepairable subassembl

43、ies, the design shall not be changed to employ nonrepairable assemblies without the approval of the procuring activity. e. Microelectronic integrated circuits and large scale integrated circuits shall be used for all arithmetic and logic functions. f. Selection and application of microelectronic dev

44、ices shall be in accordance with MIL-STD-454, Requirement 64. All second source microelectronic devices and components shall be mechanically and electrically interchangeable. microcircuits. Devices shall be soldered or welded into the circuit. Precap inspection is required for all g. h. Circuits sha

45、ll be designed to use a minimum of different materials, parts, subassemblies, cards and modules. All passive circuit components shall be established reliability (ER) devices, f ai 1 ure rate level “M“ or better. i. Semiconductors shall be JAN TX, or better. j. The use of magnesium, metallic oxide re

46、ctifiers, nonhermetically sealed wet tantalum capacitors (MIL-C-3965 Types) , aluminum capacitors (MIL-C-62 Types) , and pl astic encapsulated semiconductors and microcircuits is prohibited. k. Purchased DMTC modular power supplies and mode display shall not be required to meet the parts selection a

47、nd derating requirements as contained herein. It shall be the responsibility of the DMTS contractor to assure compliance with MIL-E-5400, MIL-STD-454 and MI L-STD-704. 8 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-c MI L-R-8 5535 (AS) 3.2.1 Nonst

48、andard parts and materials approval. Approval for the use of nonstandard parts and materials, including electron tubes, transistors, diodes and microelectronic devices, shall be-obtained (see 6.2.2) as outlined in MIL-E-5400. Microelectronic devices shall be approved as outlined in MIL-STD-965, exce

49、pt that approval shall not be required for devices which are: a. Listed in MIL-STD-1562 b. Available from at least two sources which are listed in the appropriate QPL of MIL-M-38510, and c. Procured to the requirements of MIL-M-38510 from a qualified source. 3.2.2 Microelectronics modular assemblies. When used, Microelectronic Modular Assemblies shall meet the requirements of MIL-STD-965. Conformal coatings