NAVY MIL-R-85535 (2)-1986 RECORDER-REPRODUCER SET DIGITAL DATA AN ASH-33《AN ASH-33型数字数据收发双用机设备》.pdf
《NAVY MIL-R-85535 (2)-1986 RECORDER-REPRODUCER SET DIGITAL DATA AN ASH-33《AN ASH-33型数字数据收发双用机设备》.pdf》由会员分享,可在线阅读,更多相关《NAVY MIL-R-85535 (2)-1986 RECORDER-REPRODUCER SET DIGITAL DATA AN ASH-33《AN ASH-33型数字数据收发双用机设备》.pdf(24页珍藏版)》请在麦多课文档分享上搜索。
1、MIL-R-85535 (2) 5 m 7777706 0175556 5 m F.-sq-c3 MIL-R-85535(AS) AMENDMENT 2 26 August 1986 SUPERSEDING AMENDMENT 1 14 DEC 1983 MILITARY SPECIFICATION RECORDER-REPRODUCER SET, DIGITAL DATA, ANIASH-33 This amendment forms a part of Military Specification MIL-R- 85535(AS) dated 8 June 1983, and is app
2、roved for use by the Naval Air Systems Command, Department of the Navy and is available for use by all Departments and Agencies of the Department of Defense. PAGE 1 1 .l, line 15: Delete “AN/AYK-l14(V)“ and substitute: “AN/AYK-l4(V) .It PAGE 3 2.1.1, After MIL-R-5757 add: ttMIL-E-6051 Electromagneti
3、c Compatibility Requirements Systems“ -_I_ C? The attached insertable replacement pages listed below are replacements for stipulated pages. insert the amendment as the cover sheet to the specification. L When the new pages have been entered in the document, Replacement Page 47 48 49 50 62A 6220, Del
4、ete in its entirety and substitute: “3.3.20 Safety. accordance with the applicable requirements of MIL-STD-882 (See 6.2.2). Primary emphasis of the safety program should be on the hazards associated with the interrelationships between the operating and maintenance personnel, the air vehicle, the var
5、ious avionics devices, and the avionics system designed to integrate this equipment into the air vehicle. For example: The system shall be analyzed to determine if unplanned or inadvertent commands are generated, critical controls shall be designed and located to preclude inadvertent operation, comp
6、uter programs shall include logic to prevent the system from entering into unsafe or dangerous mode of operation. and its components shall be designed and the CFE developed for safety in accordance with MIL-E-5400. The contractor shall conduct a system safety program in The system 3.3.20.1 X-Radiati
7、on exposure. X-radiation producing equipment shall be designed to limit the personnel dosage rate at any readily accessible point, measured two inches from the outer surface, to a 0.5 millirem per hour with external shielding removed or 500 millirem per year (BIMED NAVMED P5055). This requirement ap
8、plies to the areas normally inhabited by personnel during installation, calibration, maintenance, and operation of equipment. 3.3.20.2 Electromagnetic radiation exposure. The system design criteria shall include provisions for protection of personnel from RF electromagnetic, electrostatic and shock
9、hazzards in accordance with requirement 1 of MIL-STD- 454. Where possible, protection provisions shall be designed into associated adequate safety precautions shall be provided. subsystem/equipments. When protection by design is not technically feasible, - 4 Provided by IHSNot for ResaleNo reproduct
10、ion or networking permitted without license from IHS-,-,-c MIL-R-85535 (2) 58 = 7777906 OL755b0 7 M MIL-R- a5 53 5 Amendment 2 3.3.20.3 Toxicity. Personnel exposure to toxic air contaminants during system operation or maintenance shall be evaluated and minimized. additior, any malfunction of the ele
11、ctrical power and distribution system, avionics or other electrical system component in the form of but not limited to electrical fires and battery chemical releases shall not release into the cockpit or cabin area any gases, fumes, vapors or particulates which could incapacitate the crew and subseq
12、uently result in inability to successfully perform an emergency landing or ditching and egress. vapors and particulates shall be positively prevented from leaking back into the cockpit or cabin area from when they are purged. In These gases, fumes, 3.3.20.4 Electronic equipment hazards. All newly de
13、signed electronic equipments and modified portions of existing electronic equipment shall be in accordance with MIL-STD-454 requirement 1.“ PAGE 40 3.4.1.3.1, last line: Delete: n3.5.2.2.2.t1 and substitute: n3.5.1.3.2.1.R 3.4.1.3.2, last line: Delete: “3.5.1.3.2.1.“ and substitute: n3.5.1.3.2.2.tt
14、3.4.1.3.3, last line: Delete: tt3.5.1.3.2.2.n and substitute: “3.5.1.3.2.3.“ PAGE 42 3.4.4, last line:, Delete: c -3 %- “SECNAVINST 3560.1 and MIL-STD-1679II and substitute: “DoD-STD-21 67“ PAGE 43 TABLE V, Description column, line 17: Delete: “Figures 10A, 10B, and 11“ and substitute: “Figures 10,
15、11, and 12.tt PAGE 46 3.5.1.1. Add: “h. Control each tape units tape motion, in DMTU Auto Mode.“ PAGE 48 Figure 10: Delete and substitute attached FIGURE 10. PAGE 49 Figure 11: Delete and substitute attached FIGURE 11. PAGE 50 Figure 12: Delete and substitute attached FIGURE 12. 5 Provided by IHSNot
16、 for ResaleNo reproduction or networking permitted without license from IHS-,-,-Y MIL-R-85535 Amendment 2 PAGE 52 TABLE IV, Type Device column, lines 18 through 23: Delete: “Mon“ and substitute “Alt.“ PAGE 54 3.5.1.3.2.2, line 11: Delete: n3.5.2.2.3w and substitute “AD 1404.“ 3.5.1.3.2.2, line 13: D
17、elete: “3.5.2.2.3.3.1“ and substitute “AD 1404.“ 3.5.1.3.2.2.1, line 6: Delete: “Xn and substitute nX-l.n PAGE 55 TABLE VI, Add vertical line between “Exception“ and llDisplayw Columns. TABLE VII, Exception column, line 6: Delete: “Out“ and substitute “Out (TO).“ TABLE VII, Normal column, line 15: D
18、elete: IDC“ and substitute “DW.“ PAGE 56 TABLE VII, NOTES: After liCIW“ add “CRS = Channel Reset SC = System Controller TO = Times Out“ TABLE VII, NOTES, lines 11 and 12: Delete: “The IDS“ and substitute “AD 1404.“ PAGE 57 TABLE VIII, Title: Delete: “ASP“ and substitute “SASP.“ TABLE VIII, Exception
19、 column, line 6: Delete: “Out“ and substitute “Out (TO).“ PAGE 58 TABLE VIII, Title: Delete: “ASP“ and substitute “SASP.“ TABLE VIII, Notes: After “DU“ add “CRS = Channel Reset SC = System Controller TO = Times Out“ TABLE VIII, NOTES, lines 10 and 11: Delete: “The IDS: and substitute “AD 1404.“ 3 .-
20、 PAGE 59 TABLE X, Exception column, line 6: Delete: “Out“ and substitute “Out (TO).“ 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-R-5535 (2) 5B 9999906 0375562 O I MIL-R-85535 Amendment 2 PAGE 60 TABLE IX, Notes: After “IPL“ add “CRS = Chann
21、el Reset SC = System Controller“ TABLE IX, NOTES, line 7: Delete: “Time Out“ and substitute “Times Out.“ TABLE IX, NOTES, lines 13 and 14: Delete: “The IDS1 and substitute “AD 1404.“ PAGE 61 TABLE X, Exception column, line 6: Delete: “Out“ and substitute “Out (TO).“ PAGE 62 TABLE X, NOTES: After “IP
22、Ln add “CRS = Channel Reset SC = System Controller“ TABLE X, line 8: Delete: “Time Out“ and substitute “Times Out.“ TABLE X, NOTES, lines 13 and 14: Delete: “The IDS“ and substitute “AD 1404.“ t-3 3.5.1.3.2.2.1, line 5: Delete: “four“ and substitute “five.“ -=A. 3.5.1.3.2.2.1, line 9: Delete: I1Xw a
23、nd substitute “X-1.“ Add Table X-1 as page 62A. Add Table X-1 (Continued) as page 62B. PAGE 63 3.5.1.3.2.2.1: Add: “e. System Loader - Table X-1.“ 3.5.1.3.2.2.1, last line: Delete: “and X“ and substitute “X and X-1,“ PAGE 64 3.5.1.3.2.2.1.5, after paragraph 3.5.1.3.2.2.1.5, and new paragraph 3.5.1.3
24、.2.2.1.6: “3.5.1.3.2.2.1.6 System Loader (SLDR) load option. hardware, initiating the system loader load option shall initiate the When implemented in the command sequence specified in Table X-l. DW sequences shown in the table shall cause the corresponding messages to be displayed to the operator.“
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- NAVYMILR8553521986RECORDERREPRODUCERSETDIGITALDATAANASH33ANASH33 数字 数据 收发 双用机 设备 PDF

链接地址:http://www.mydoc123.com/p-981444.html