NAVY MIL-P-87098-1987 PARKA WET WEATHER《潮湿天气用皮制大衣》.pdf

《NAVY MIL-P-87098-1987 PARKA WET WEATHER《潮湿天气用皮制大衣》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-87098-1987 PARKA WET WEATHER《潮湿天气用皮制大衣》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、c -sLp-s MIL-P-87098 14 October 87 MILITARY SPECIFICATION PARKA, WET WEATHER This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for a waterproof parka, made of a double coated nylon twill

2、 cloth. 1.2 Classification. The parka shall be of one type, and shall be procured in the following sizes as specified (see 6.2): XX Small - (26-28) X Small - (30-32) Small - (34-36) Medium - (38-40) Large - (42-44) X-Large - (46-48) 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specificati

3、ons, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications an

4、d Standards (DoDISS) and supplement therto, cited in the solicitation. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmo

5、re Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. c AMSC1NA FSC 8405 DISTRIBUTION STATEMENT A. Approved for public release; distribution is un1 imi t ed . O THIS DOCUMENT CONTAIN

6、S 4 For Clothing, Equipage, and Tentage (General Use) MI LI TARY MIL-F-10884 - Fasteners, Snap MIL-P-15011 - Pallet, Material Handling, Wood, Post Construction, MIL-G-16491 - Grommet, Metallic MIL-B-17757 - Boxes, Shipping, Fiberboard (Modular Sizes) MIL-C-19759 - Cloth, Coated, Twill, Nylon (Low Co

7、unt) MIL-F-21840 - Fastener Tapes, Hook and Pile, Synthetic 4 Way Entry STANDARDS FEDERAL FED-STD-191 - Textile Test Methods FED-STD-751 - Stitches, Seams, and Stitchings MIL I TARY MIL-STD-105 - Sampling Procedures and Tables for Inspection by At tributes MIL-STD-129 - Marking for Shipment and Stor

8、age MIL-STD-147 - Palletized Unit Loads (Copies of specifications, standards, drawings, and publications required by contractors in connection with specific procurement functions should be obtained from the procuring activity or as directed by the contracting officer) . 2.1.2 Other Government docume

9、nts, drawings, and publications, The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. LAWS AND REGULATIONS US POSTAL SERV

10、ICE MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402). f .T P 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-87078 84 W 7997906 0433353 3 MIL-P-8 7 O 9 8 2

11、.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of documents which are DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the

12、 issues of documents not listed in the DoDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT Nat ional Mot or Freight C1 as si f i cat ion (Applications for copies should be addressed to the

13、American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036) a UNIFORM CLASSIFICATION COMMITTEE, AGENT Uni f om Freight C1 as si f i cat i on (Applications for copies should be addressed to the Uniform Clas-sification Committee, Room 1106, 222 South Riverside P

14、laza, Chicago, Illinois 60606). 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations un

15、less a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the sample in which case this specification shall govern. 3.2 First article. W

16、hen specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Basic material. The basic material for the parka shall be a chloroprene coated nylon twill conforming to Type II of MIL-C-19759, except that the coating shall b

17、e unvulcanized. The cloth shall be tested as specified in 4.4.1. 3.3.2 Braid, tubular, elasticized. The hood drawcord shall be of 1/8 inch diameter, rayon-covered, 6-strand rubber cord braid such as that commercially available from Thomas Taylor and Sons, 50 Houghton St. Box A, Hudson, Ma. 01749, St

18、yle No. 16450 or the equivalent (see 6.4). 3.3-3 Cement, chloroprene. The cementing compound shall have a chloroprene base and the same curing characteristics as the coating compound specified in 3.3.1. The use of reclaimed rubber is prohibited (see 4.4.1). Cemented sample seams shall have a minimum

19、 adhesion of 5 pounds per inch width when tested as specified in 4.4.1. The color of the cement shall approximate the 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-87078 84 W 7999906 04LlL54 5 MIL-P-87098 shade of the green coating compound

20、 specified in 3.3.1 or shall be unpigmented. 3.3.4 Thread, nylon. The nylon thread used for all seaming and stitching shall conform to Type III, size B or E, of V-T-295, except that the colorfastness requirements shall not apply. The color shall approximate the green shade of the basic material. * 3

21、.3.5 Fastener tapes. The fastener tapes shall conform to Type II, Class 3 or 5, of MIL-F-21840. The tapes shall be 1 inch or 2 inches in width (see Table I), The color shall be Green 3422. c 3.3.6 Webbing, elastic. The elastic webbing used in the waist of the parka shall conform to Type 1, Class 3 o

22、r 4, of JJ-W-155. The elastic webbing for the hood adjustment strap assembly shall conform to Type 1, Class 6 of JJ-W-155. Class 4 webbing shall be black. Class 6 webbing shall be dyed to approximate the green shade of the basic material. Class 3 webbing shall be unbleached, bleached or dyed to appr

23、oximate the green shade of the basic material. 3.3.7 Bias tape. The bias tape used as stay stripping or seam strapping shall be any suitable plain woven fabric, weighing not less than 2.5 oz. per square yard (see 4.4.1). The cloth shall be dyed to harmonize with the shade of the back side of the bas

24、ic cloth and bias cut to the width required. (see Table I). Any continuous length used for the construction of the parka shall contain not more than two seams. As an alternate, the basic material specified in 3.3.1 may be used. When basic material is used, any continuous length shall not be spliced

25、or seamed. a 3.3.8 Fasteners, slide. The slide fastener for closing the front opening shall be interlocking short or long tab pull, natural brass or bronze or plastic (nylon) chain conforming to Type IV, Style 8, Size M of V-F-106. The color of the tape shall be black or shall approximate the green

26、shade of the basic material. The tape shall be cotton, synthetic or a combination of both. When cotton is used, it shall be mildew-resistant treated (see 4.4.1). All components of the slide fastener shall be furnished by the same supplier (see 4.4.1). The top tape extension beyond scoops shall be 1

27、1/8 inches maximum. The length of the slide fastener chain for each size parka shall be as follows: Size of Parka Length (inches) XX Small, X Small Small and Medium 24 (+ - 1/41 25 (+ 1/41 Large and X Large - b The thong for the slide fastener tab pull shall be as specified in V-F-106, except that t

28、he finished length after attachment shall be 3 to 4 inches. The color of the thong shall approximate the green shade of the basic material or P shall be black. 3.3.9 Grommets. The grommets for the hood assembly drawcords shall conform to Type I, Class 3 Size O or 1 of MIL-G-16491. 4 Provided by IHSN

29、ot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I MIL-P-87098 8LJ 779970b OLJ11155 7 m MIL-P-87098 b % a f 3.3.10 Fasteners, Snap. The snap fasteners used or the bottoin closure of the parka (see Table I operation 16d. and Figure 3) shall consist of a stud and butto

30、n (attached to right moisture barrier) and a socket and button (attached to left moisture barrier). The fasteners shall be Style 2, 24 line, Size 1 or 2 of MIL-F-10884, with a black or commercial dark finish on the button portion. 3.3.11 Combination label. A combination identification, size, and ins

31、truction label, conforming to Type IV, Classes 12 and 13, of DDD-L-20, shall be printed on a suitable sized piece of unvulcanized basic material or may be marked directly on the parka. Ail markings shall be bright yellow in color. The inscription shall be as follows:. PARKA, WET WEATHER CONTRACT NO.

32、 DLA-100-00-0-0000 (EXAMPLE) STOCK NO. 8405-00-000-0000 (EXAMPLE) SIZE: MEDIUM (38-40) (EXAMPLE) NAME OF CONTRACTOR INSTRUCTIONS THIS WATERPROOF PARKA HAS BEEN OVERSIZED TO FIT OVER HEAVY CLOTHING FOR USE UNDER COLD/ WET WEATHER CONDITIONS. IF TOO LARGE WHEN WORN SIZE MAY BE ADJUSTED BY THE USE OF T

33、HE INNER HOOD ADJUSTMENT STRAP. OVER LIGHT CLOTHING, USE A SMALLER SIZE. HOOD RINSE GARMENT WITH A HOSE OR SPONGE USING FRESH WATER AFTER EVERY USE. DO NOT DRY CLEAN. 3.3.12 Dusting medium. The dust used in fabricating both the basic material and parka shall be applied in the smallest quantity neces

34、sary to prevent blocking. The dust shall consist of a finely powdered mineral material such as talc, except that the addition of zinc stearate to the medium is permissable in an amount that will not support mildew growth on the finished vulcanized parka (see 4.4.1). 3.4 Design. The parka shall be ja

35、cket style, cement-constructed and vulcanized, have a slide fastener front closure with double moisture barrier flaps, patch pockets and have a permanently attached, oversized 2-piece hood assembly with adjustable elasticized drawcord closures and a size adjustment strap at the center of the inner h

36、ood. Hook and pile fastener tape tabs shall be provided at sleeve bottoms for take-up and at neck for proper closure. The two front patch pockets with flaps shall fasten with hook and pile tape closures. Elastic shall be inserted in the back parka hem and a snap closure shall be provided at the bott

37、om front (see Figures 1 and 2). 3.4.1 Figures. Figures 1 through 6 are furnished for information purposes only. When inconsistencies exist between the written specification and the figures, the written specification shall govern. 5 Provided by IHSNot for ResaleNo reproduction or networking permitted

38、 without license from IHS-,-,-MIL-P-87098 3.5 Patterns. Standard patterns will be furnished by the Government. The standard patterns shall not be altered in any way and are to be used for cutting the contractors working patterns. The working patterns shall be identical to the standard patterns. 3.5.

39、1 Pattern parts. The component parts shall be cut from the material 1 specified, and in accordance with the following pattern parts: c Mat er i al Pattern Parts Cut parts Cloth coated, nylon twill Front 2 Back not serving intended purpose Not size specified Insecure or loose stitch tension Not conta

40、ining the required number of stitches Puckered, twisted, or pleated Irregular in width by 1/4 inch or more Width of sleeve hem less than 1/2 inch Width of sleeve hem more than 3/4 inch Width of bottom hem less than 1 inch Width of bottom hem more than 1 1/4 inches Elastic in back hem not positioned

41、as specified Elastic caught in hem stitching Fronts distorted, not abutted or bottoms uneven by more than 1/2 inch when bottom snap is fastened 10. Snap fastener assembly not as specified 11. Center front hems less than 3/4 inch 12. Center front hems more than 1 inch IX Sleeve tab(s) and take-up tap

42、e assemblies 1, Any part omitted or insecurely attached 2. Any part misplaced or distorted: X X X X X X X X X X X X X X X X X X 28 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-87098 4 = 7997906 OLiLlL79 T m Classification Defect Major Minor

43、a. Not serving intended purpose b. Serving intended purpose 3. Sleeve tab or take-up tape assembly with a loose or unaffixed edge: a. be X Pockets Up to 1/4 inch inclusive in length or depth More than 1/4 inch in length or depth 1. Set on crookedly or poorly shaped 2. V-s ay strip omitted or misplac

44、ed 3. Bias tape V-stay strip (when applicable) contains more than two seams 4. Basic cloth V-stay strip (when applicable) spliced or seamed 5. Incorrect size, design or configuration 6. Irregular in width by 1/4 inch or more XI Hood. a. Outer hood. 1. Bottom hem less than 5/8 inch or more 2. Front h

45、em less than 1/4 inch or more 3. Not attached to inner hood as specified than 3/4 inch than 3/8 inch b. Inner hood. 1. Front edge binding omitted or insecurely attached 2. Neck tab misplaced or distorted a. Not serving intended purpose b. Serving intended purpose 3. One or both sets of headset holes

46、 missing 4. Adjustment strap omitted or insecurely attached 5. Adjustment strap misplaced or distorted: a. Not serving intended purpose b. Serving intended purpose 6. Self material strips: one or more missing, misplaced or distorted X X X X X X X X X X X X X X X X X X X X X 29 Provided by IHSNot for

47、 ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P -8 7 O 9 8 - Classification Major Minor Detect 9. Inner hood not attached to parka as specified X XII. Fronts. 1. Closed fronts uneven at top or bottom by 1/2 inch or more XLII. Hood drawcord. 1, mitted 2. Other than t

48、ype specified 3. Length not as specified 4. Not knotted, or knot too small to prevent cord from slipping through grommet eye or end of tunnel 5, Not tipped at end 6. Caught in hem stitching, or otherwise non functional XIV. Slide fastener assembly. X X X X X X 1. Stitching too close to chain, not pe

49、rmitting 2, Any part broken, bent or otherwise slider to pass freely X damaged or nonfuctional X 3. Length of slide fastener not as specified X 4. Thong omitted or not as specified X barrier flaps X out of alignment X 5. Top of slide fastener less than 1 3/4 inches or more than 2 inches below top raw edge of moisture 6. Top teeth of left and right slide fastener chains 7, Tape or moisture barrier flaps set on too loose or too tight causing waviness, twistin