NAVY MIL-P-19611 C-1985 PLATES AUTOMOBILE INDIVIDUAL METAL EMBLEM AND STAR (COMMANDANT-S AND GENERAL OFFICER-S USMC)《金属徽章和星个人汽车牌照(美国海军陆战队司令员和将官)》.pdf

《NAVY MIL-P-19611 C-1985 PLATES AUTOMOBILE INDIVIDUAL METAL EMBLEM AND STAR (COMMANDANT-S AND GENERAL OFFICER-S USMC)《金属徽章和星个人汽车牌照(美国海军陆战队司令员和将官)》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-19611 C-1985 PLATES AUTOMOBILE INDIVIDUAL METAL EMBLEM AND STAR (COMMANDANT-S AND GENERAL OFFICER-S USMC)《金属徽章和星个人汽车牌照(美国海军陆战队司令员和将官)》.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、4w . m 0 MIL-P-LSbLLC 83 SS9990b OL2L1Ob T m MIL-P-I 961 IC (MC) MIL-P-19611B (MC) 5 January i971 MILITARY SPECIFICATION PLATES, AUEMIOBILE, INDIVIDUAL: ME;TAl;t EMBLEM, AND STAR (CmS AND GENERAL OFFICERS, USMC) This specification is approved for use ky the U. S. Marine Cows, Departmnt of the Navy,

2、and is available for use by all Departments and Agencies of the Departmnt of Defense. I. SCOPE 1.1 Scope. This specification covers requirements for mtal individual automobile plates and attachable metal emblem and stars. 1.2 Classification. Individual autombile plates shall be of the following type

3、s, as specified (see 6.2). ZLpe I - Plate, Automobile, Individual: Metal ?“pe II - Plate, Autombile, Individual: Metal (Conmiandants UsMc) (General Officers, UsMc) Emblem and stars shall be furnished as specified (see 6.2). 2.1 Goverment documents. 2.1.1 Specifications, standards, and handbooks. Unl

4、ess otherwise specified, the following specifications, standards, and handbooks of the issue listed in that issue of the Department of Defense Index of Specifications ana Standards (DODISS) specified in the solicitation form a part of this specification to the extent -specified herein. Beneficial co

5、mments (recomrrirndations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to the Commandant of the Marine Corps (LMA-l), Headquarters, U. S. Marine Corps, Washington, Dc 20380, by using the self-addressed Standardization Document Impro

6、vement Wopocal (DD Form 1426) appearing at the end of this document or by letter. FSC 8345 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIIP-1961 lC(MC) SPECIFXATIONS FEDERAL FF-N-845 QQ-C-320 QQ-S-698 Q(-S-763 FED-STD-Ha 8 FED-STD-15 1 FED-STD-59

7、5 MILITARY MIL-STD-I 05 MIL43TD-129 Nut, Plain, Wing, Inch and Metric Tkst Methods. *lor. -SanipLing Procedures And Tables For Inspctions By -Marking For Shipment And storage. Attributes . (Copies of specifications, standards, handbooks, drawings, and publications required by mnufactureis in connect

8、ion with specific acquisition functions should be obtained from the contracting activity or as directed iq the contracting officer. ) 2.1.2 ther Government documents, drawings, and publications. The EoLJ.owin other Government documents, drawings, and publications fom a part of this specification to

9、the extent specified herein. I;AFss AND REGULATSONS U. S. PostalService Manual * (Application for copies should be addressed to the Superintendent of DocUments, U, S. Government Printing ffice, Washington, DC 20402.) 22 Cher publications. Tne following documents form a part of this specification to

10、the extent specified herein. %he issues of the documents which are indicated as DOD adcpted shall be the issue listed in the current DODISS and the supplemnt thereto, if applicable, UNIFORM CW1SSIFICATION COEIMImEE Uniform Weight Classif icatlon the star shall be plated with a mppr plate, a nickel p

11、late and a chrm finish. 3.3.3 Screw posts, nuts, and washers, Screw posts, wing nuts, flat washers, and-l alternately screw posts may be or brass ccarsnercial wing nuts which are cadmium plated and have a nylon insert my be length of 1/2 inch. The threads sFall be No. 10-24 uNc-2A In accordance with

12、 FE-C!CR-i28* Itie wing nut shall be No, IO-24-UNC-26 in acmrdance with type A, style 2 of FF-N-845, All smew posts shall be provided with a flat washer, lock washer and wing nut. used: The screw post shall be .3/4 + 1/32 inch long and threaded or a minimum ? .+ . 3.4 ksign and construction, The pla

13、tes, emblem and star shall be mde of the materials specified herein and constructed to include the mponents and construction details shown on Figures 1, 2 and 3 and specified herein. After fabrication, the surfaces of the plates shall be visibly flat, and free from sucface recesses, protrusions, or

14、other imperfections which might afect the smoothness, appearance, or serviceability of the enamel. Al1 edges of the plate (including the holes), star and emblem shall be trimd so as to be 3.4.1 Plate construction. Before painting, the plates shall be clean, and all surfaces and edges shall be smooth

15、 and free of sharp corners. !he plates shall be surface prhd with the white paint and enameled with the red paint specified in 3.3.1.2. All surfaces and edges of the plates shall be completely and evenly mated with the paint in such a mnner that a smoth uniform film will be produced. The film shall

16、be uniform in color without objectionable orange peel, runs, wrinkles, drops, streaks, or areas of thin or no film, and shall be Eree of bubbles or foreign inclusions or other defects which may affect appearance or serviceability, a clean, smooth and free from drag and step. 3.4.2 -lem and star cons

17、truction. 3.4.2,l Molds, The emblem shall be cast in mlds made from the standard me star shall be cast in The finished emblems and stars shall be free of The mold of the star, unless model loaned to the contractor by the Government. molds made by the contractor. dents, nicks, scratches and other imp

18、erfections. otherwise specified (see 6.2), shall remain the property of the contractor. The screw post for the star shall be 3/4 + 1/32 inch long embedded in the mld before casting and shall be centered and perpendicular to the back surface. Ihe screw posts for the emblem shall be soldered to the ca

19、sting, at the locations sham in Figure 3, with hard solder having a mlting point not less than 1,075F. Care chould be taken to insure that the post is perpendicular to the back surface, All flux and excess solder shall be completely raroved and the joint shall be clean, strong, swth and Eree from bu

20、rned or reduced areas. Bsts shall have a free length of 1/2 to 5/8 inch when masured rom the back edge of casting to end of pst, . 3.4.2.2 Screw posts. 4 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-1762LC 83 7977706 0182410 L *6 MIG.P-i96

21、1 IC (MC) 3.4.2.3 Plating. Zhe finished emblem castings, before plating, shall be free frm pits, holes, and nicks, and pnperly buffed and polished to a mirror-like finish, degreased, and cleaned. Elnblem castings shall be first plated with nickel, recleaned, and then plated with rhodium. All plating

22、 shall be continuous and nonporous with no indication of cut-thrwgh, blistering, or peeling. The nickel plating shall be not less than 0.0003 inch in thickness. !he rhodium plating shall be not less than 1 gram per 1,000 square inches of surface. For the purpose of this specification, the emblem cas

23、tings shall be ansidered properly plated when tested as specified in Section 4, Table PII. The star casting shall conform to requirements specified in w-320. 3.4.2.4 Cork backing for star. Each star shall be provided with a mrk backing, 1/16 inch minimum thickness. Ihe backing shall be star shaped,

24、measuring 1-5/8 to 1-3/4 inches from point to point and shall not extend beyond edges o the star. Trie mrk shall be securely adhered to the back of the star with a water-resistant adhesive. 3.5 Government-loaned property. A standard moel of the emblem will be loaned to the contractor by the Governme

25、nt. The Government furnished starklard del shall be used only for making the contractors wrking molds, Upon oonp?letion of the contract, the standard niode1 shall be returned to a point designated by the contracting officer. The mntractor shall be responsible for the loss, damage, or nutilation of t

26、he Government furnished standard del while in his possession. Determination of cost of replacing the lost, broken or damaged standard amended, modified, or qualified in this specification or applicable purchase documents. In addition, testing shall be performed on camponents listed in Table II for t

27、he characteristics shown. fiere shall be two dteminations for each element per sanple unit and the results shall be reported to the nearesk O. 1 percent. fie sample unit shall be a minimum of 8 ounces or equivalent for each alloy. *e requirements are applicable to lot average and the inspection leve

28、l shall be S-I. * Table II. Conpnent testing. Requirement Test Component Characteristic paragraph method alloy for conposition 112 of appx base Chemical. 3.3.2.1 Method 111 or Frnblems FED-S” gross/net weight exceeds requiremnts. 4.6 Tests. First article testing shall be in accordance with Tables II

29、 and III amitem testing of the qletely fabricated plate and emblem shall be in accordance with Table III for the characteristics shown herein. 4.6.1 Irest for continuity of rhodium plating. Test samples of rhodium- plated emblems shall be immrrsed for 10 minutes in a solution of liver of 10 Provided

30、 by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-L7bLLC 3 m 9977906 OL24Lb 2 m - x MIL-P-1969 1C (MC) M M 4 m 11 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-1961 IC (MC) sulfui: (2 Percent Pota

31、ssium sulfide and 96 percent water by weight) at a temperature of 100F + IOOF. Mter removal, the samples shall be washed clean in water and examined. mere shall be no perceptible change in brightness on the plated surfaces, except along the outside edge there my be a slight darkening, 5. PACKAGING 5

32、.1 Packaging. Packaging shall be level A or comnrsrcial as specified (see 6,2) ? 5.1.1 hvel A. Plates shall be individually wrapped in kraft paper sealed with gummed kcaft: paper tape. Wlm and stars, equippe with a flat washer, a. lock washer, and a wing nut mounted on each smew post, shall be indiv

33、idually wamd with leece-ba red background; lg 9-1/2 in, w 7-1/2 in. .cupe II Plate: PLATE, AVMMOBILE, INDIVIDUAL: netal; red background; Ig 9 in. , w 6 in. Star: STAR, AIWOBILE, INDIVIDUAL PATE: metal 6.1 Intended use. The metal individual plates and attachable metal emblem and stars are intended or

34、 autombiles used by the Cormiandant and general officers of the Marine Corps. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-LShLLC 3 7737706 OL24L b W MGP-1961 IC(MC) 6.2 Ordering data. 6.2.1 Acquisition requirewnts. Ihe acquisition documents

35、 should specify the following: (a) Title, number and date of this specification. (b) Type plate required (see I . 2) . (e) Bnblenr; and stars required (see 1.2). (e) When mld of star shall not remain property of supplier (see (E) Selection of applicable levels of packaging (see 5.1). c (ti) Whether

36、f irct article is required (see 3.2). 3.4.2,l). 6.2.2 Data requirements. When this specification is used in an acquisition which incoqxxates a DD Fbnn 1423, Contract Data Requirements List (CDRL), the data requirements identified below shall be developed as specified by an approved Data Item Descrip

37、tion (DD Ebnn 1664) and delivered in accordance with the approved CDRL inaxporated into the contract. When the provisions of DAR 7-104.9 (n) (2) are invoked and the MI Ebrm 1423 is not used, the data specified beluw shall be delivered by the contractor in accordance with the contract or purchase ord

38、er requirements. Bliverable data required by this specification is cited in the following paragrams. Paragraph no. Data requirements Applicable nIi3 no. Wtions 4.2 4.4 4.4 4.5 Inspection System Program Plan DI-R-4803 First Article Inspection DI*-4901 Procedure First Article Inspection DI-T-4902 Repr

39、t Woduction/Acceptance DI*-4903 Inspection Procedures I- I - 4.5 Production Inspection Reports DI*-4904 ReprEs, Sest DI+)?-2072 U- 4.6 (Data item descriptions related to this specification, and identified in section 6, wil1.k amroved and listed as such in DoD 5000.19L., Vol. II, connection with spec

40、ific acquisition functions should be obtained from the Naval Publications and Fonns Center or as directed by the contracting officer. ) s AMSDL. Copies of data item descriptions required by the contractor in 6.3 Standard sample. For infotmation regarding the availability of the standard sample plate

41、s, emblem, and star, address inquiry to the procuring activity issuing the invitation for bids. e 13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P- 1 96 1 IC (MC ) c 6,4 First article. Examination, test and approval shall be as speciEi& by th

42、e contracting officer (see 3.2). 6.5 Changes from previous issue, Asterisks are not used in this revision to identiy changes with respect to the previous issue due to the extensiveness of the changes. Preparing activity: Project No. 8345458 Navy - MC 4 c 14 Provided by IHSNot for ResaleNo reproducti

43、on or networking permitted without license from IHS-,-,-MIL-P-376L3C 83 m 7777706 O382420 4 MIL-P-19611C (MC) -e- I I l I J 15 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-cw r d w i- =z I 16 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-P-L7622C 83 7777706 0282422 II LLn STAR 17 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-