NAVY MIL-P-18716C-1991 PRIMER ELECTRIC MARK 48 MOD 2《MARK 48 MOD 2 电发火器》.pdf

《NAVY MIL-P-18716C-1991 PRIMER ELECTRIC MARK 48 MOD 2《MARK 48 MOD 2 电发火器》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-18716C-1991 PRIMER ELECTRIC MARK 48 MOD 2《MARK 48 MOD 2 电发火器》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、- t y. -1 MIL-P-LB7LbC 13 779770b 0473276 5 I INCH-POUND I I I MIL-P-187 16C 27 March 1991 SUPERSEDING 7 February 1977 MIL-P-187 16B(OS) MILITARY SPECIFICATION PRIMER, ELECTRIC, MARK 48 MOD 2 This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOP

2、E 1.1 Scope. This specification establishes the minimum requirements for the Electric Primer, Mark 48 Mod 2, herein referred to as the “primer.“ 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specif

3、ication to the extent specified herein. Unless otherwise specified the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the specification (see 6.2). - SPECIFICATIONS FEDERAL PPP-B

4、-636 Boxes, Shipping, Fiberboard MILITARY MIL-D-3464 Desiccants, Activated, Bagged, Packaging Use and Static Dehumidification Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commanding Officer,

5、Naval Ordnance Station, Standardization Branch (Code 3730), Indian Head, MD 20640-5000 by using the Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or sending a letter. AMSC NIA FSC 1390 DISTRIBUTION STATEMENT A. Approved for public release; distrib

6、ution is unlimited. Licensed by Information Handling ServicesMIL-P-L7LbC 13 W 999990b 0473297 7 D MIL-P- 187 16C STANDARDS MILITARY MIL-STD-129 Marking for Shipment and Storage MIL-STD-33 1 Fuze iind Fuze Components, Environmental and Performance Tests for MIL-STD-453 Inspection, Radiographic MIL-ST

7、D-1167 Ammunition Data Card MIL-STD-1168 Ammunition Lot Numbering DOD-STD-2101 Classification of Characteristics (nless otherwise indicated, copies of federal and military specifications and military standards are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Aven

8、ue, Philadelphia, PA 191 11-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the da

9、te of the solicitation (see 6.2). DRAWINGS NAVAL SEA SYSTEMS COMMAND (CAGE CODES loo01 AND 53711) 2434756 Primer, Electric, Mark 48 Mod 2 2847233 Charge, Propelling, 5-Inch, 38 Caliber, Full, Mark 63 Mod 1 5166058 Pack, Primer, Mk 43 Mod 1 Primers for Gun Cartridges, 5-Inch and Larger 5166059 Shippi

10、ng Condition, Primer for Gun Cartridges, 5-Inch and Larger in Pack, Primer, Mk 43 Mod 1 (Application for copies of NAVSEA drawings should be addressed to: Commanding Officer, Naval Ordnance Station, Attn: Code 802, Louisville, KY 40214.) PUBLICATIONS NAVAL SEA SYSTEMS COMMAND (CAGE CODE 1oo01) OD 49

11、540 Functioning Test of Electric Primers 2 Licensed by Information Handling Services-. a e a 1 MIL-P-1871bC 13 9999906 0973298 9 MIL-P-18716C (Application for copies of ODs should be addressed to: Commanding Officer, Naval Ship Weapons Systems Engineering Station, NAVSEA Data Support Activity (Code

12、5H30), Port Hueneme, CA 93043 .) WR-531884 Palletking Domestic Unit Load (Application for copies of WRs should be addressed to: Commanding Officer Naval Publications and Forms Center, (ATTN: NPODS) 5801 Tabor Avenue, Philadelphia, PA 19120-5099.) CODE OF FEDERAL REGULATIONS (CFR) 49 CFR 100-199 Tran

13、sportation (The Code of Federal Regulations is available from the Superintendent of Documents, US Government Printing Office, Washington, DC 20402.) 2.2 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specificat

14、ion shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected to first article inspection (see 6.4) in accordan

15、ce with 4.4. 3.2 Characteristics. The primer shall conform to all the requirements specified herein and on Drawing 2434756 and associated documents. 3.3 Radiographic (MlOl). The primer shall not exhibit any discernible gaps as identified in figure 1 (see 4.7.1). Gap no. 3 Gap no. 1 cupnO.2 , Figure

16、1. GaD Identification. 3 Licensed by Information Handling ServicesMIL-P-187LbC 13 m 999990b 0473299 O m MIL-P- 1 87 16C 3.4 Black powder moisture content (M102). The moisture content of the black powder within the primer shall not exceed 0.70 percent by weight (see 4.7.2). 3.5 Detail strip. The prim

17、er and all its components shall conform to the following requirements (see 4.7.3): a. (Ci) Each critical characteristic shall be as specified in the applicable documents listed on Drawing 2434756 and in this specification. (M103) Each major characteristic shall be as specified in the applicable docu

18、ments listed on Drawing 2434756 and in this specification. b. 3.6 Electrical resistance (M104). The primer shall have an electrical resistance of O. 10 to O. 18 ohm (see 4.7.4). 3.7 Functional. The primer shall meet the following criteria (see 4.7.5): a. b. c. d. (M105) Primer functioning time shall

19、 be a maximum of 0.006 second; (M106) The primer shall not misfire (see 6.7.1); (M107) The primer shall not exhibit blowback (see 6.7.2); and (C2) The primer shall not exhibit a split stock, split tube, or detachment of metallic components other than blowout of ignition element closing discs. 3.8 Vi

20、bration. The primer shall meet the following requirements (see 4.7.6): a. b. (C3) The primer shall not function during vibration; (C4) The stock and tube shall maintain material integrity and the primer shall maintain assembly integrity at the mating threads of the stock and tube during vibration; (

21、M108) The primer shall not otherwise physically breakdown during vibration; c. d. e. The primer shall meet the requirements of 3.6 after vibration; and The primer shall meet the requirements of 3.7 after vibration. 3.9 Ballistics. The primer when assembled into a 5“/38 propelling charge shall provid

22、e ignition which will meet the requirements of 3.7 b., c., d., and the following (see 4.7.7): a. (M109) The ejection time of the projectile from the gun barrel shall not be greater than 0.050 seconds after application of firing energy. 4 O a e Licensed by Information Handling Services/ ._ b MIL-P-18

23、71bC 13 W 9799906 0473300 3 3.10 Workmanship. All parts shall be free of chips, dirt, grease, rust, and all other foreign materials. There shall be no burrs or other imperfections of manufacture which would affect the assembly, functioning, or handling of the product. The cleaning methods used shall

24、 not be injurious to any of the parts, nor shall the parts be contaminated by the cleaning agents. All markings shall be legible. e 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract, the contractor is responsible for the performance of all

25、inspection requirements as specified herein. Except as otherwise specified in the contract, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the government. The Government reserves the right to

26、perform any of the inspections set forth in this specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. 4.1.1 Responsibility for compliance. All items must meet all requirements of section 3 and 5. The inspection set forth in thi

27、s specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or supplies submitted to the Government for accept

28、ance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requirements; however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the

29、 Government to acceptance of defective material. 4.2 Classification of inspections. The inspection requirements specified herein are classified as follows: a a. b. First article inspection (see 4.4) Quality conformance inspection (see 4.5) 4.3 Test and examination methods (see 6.2). Primers shall be

30、 selected at random for each test or examination. Identification of each primers complete test and examination results shall be secured for additional examination until otherwise directed by the contracting activity (see 6.6). 4.4 First article inspection. The first article shall be a homogeneous sa

31、mple of 130 assembled primers and five each of every component part and subassembly (less explosive components) fabricated, packaged, and packed in accordance with the requirements of this specification and the contract or purchase order using the methods and procedures to be used for production. Th

32、e first article shall be submitted to the facility designated in the contract or order for test and examination in accordance with the first article inspection plan of table I (see 6.2 and 6.4). 4.4.1 First article sample rejection. Failure of the first article sample to meet any of the requirements

33、 shall be cause for rejection of the sample. a 5 Licensed by Information Handling ServicesMIL-P-L71bC 33 = 9999906 0473303 5 MIL-P-187 16C O000 O000 x O0 o O0 o u! 2 4f o. W v) 4,- oc 6 Licensed by Information Handling Servicesc MIL-P-L87LbC 13 99999Ob 0473302 7 MIL-P-187 16C 4.5 Quality conformance

34、 inspection. 4.5.1 Lot formation. Unless otherwise specified in the contract or purchase order (see 6.2), production lots shall consist of not more than 20,000 homogeneous primers plus those required for inspection (see 4.5.2). Each production lot shall contain only one Class 2 black powder lot and

35、one Class 4 black powder lot and only one tubing heat treat lot. 4.5.2 Inspection. Unless otherwise specified in the contract or urchase order (see 6.2), 105 samples shall be selected at random from each production lot for test and examination in accordance with the quality conformance inspection pl

36、an of table 1. 4.6 Classification of characteristics. The characteristics verified by the tests and examination herein are classified as critical, major, or minor in accordance with DOD-STD-2101. Requirements for critical characteristics are identified by the symbol (C) and major characteristics by

37、the symbol (M). The number following the classification symbol indicates the serial number of the characteristic. Requirements not annotated with a classification code are classified as minor. 4.7 Methods of inspection. 4.7.1 Radiographic. The primer shall be subjected to a radiographic inspection i

38、n accordance with MIL-STD-453. The primer shall be mounted in the vertical position with the primer stock up and X-rayed perpendicular to its axis, focused at a point 0.6 & 0.2 inch from the stock face. Any primer which meets the requirements of 3.3 but appears to have been misassembled shall be sub

39、jected to detail strip and shall meet the requirements of 3.5. 4.7.2 Determination of moisture content. Moisture analysis procedure for the black powder shall be as follows: a. b. C. d. e. Ten grams (10.0 g) black powder from each sample primer shall be tested in the granular form for moisture conte

40、nt. The black powder shall be removed from primer tubes and placed in a dry container with a tight cover. Black powder shall not be exposed to the atmosphere for more than 3 minutes. Sample containers must be covered and placed in a desiccator until ready to test the moisture content. Carefully weig

41、h 2.0 & 0.1 grams of sample into a tared weighing dish or container. The sample shall be weighed to the nearest 0.1 mg. Black powder shall not be exposed to the atmosphere for more than 3 minutes. Uncovered samples shall then be placed in an oven at 70 to 75C. Do not draw vacuum. 7 Licensed by Infor

42、mation Handling ServicesMIL-P-1871bC 13 99999Ob 0473303 9 W MIL-P-187 16C f. After 4 hours minimum (4 1/2 hours maximum), remove samples from oven, cover and place in a desiccator to cool. After cooling, carefully weigh samples to the nearest 0.1 mg. calculate the percent moisture as follows: E C Pe

43、rcent moisture = - x 100 Where: C=A-B E=A-D and A = Sample weight plus container weight, undried, g B = Undried container weight, g C = Undried sample weight, g D = Sample weight plus container weight, after drying, g E = Weight difference, after drying, g 4.7.3 Detail strip. The primer shall be dis

44、assembled to determine conformance to all Le discernible critical and major characteristics specified on Drawing 2434756. All inspections shall be performed at the highest level of assembly possible. 4.7.4 Electrical resistance. The primer electrical resistance shall be measured by using a test circ

45、uit which limits the bridge current to 50 milliamperes maximum. The primer stock and the electrode shall be used as terminals, Fifteen to twenty pounds force shall be applied to the electrode during resistance measurement with a probe having a 0.050 +. 0.005 inch spherical radius. Assure hat contact

46、 on clean bright surfaces is obtained. 4.7.5 Functional. The primer shall be subjected to the functioning test of OD 49540. 4.7.6 Vibration, The primer shall be subjected to the transportation vibration test of MIL-STD- 331, Test BI, section 6.1.2, table B1-4, except that the orientation of each pri

47、mer during this three phase test shall be as follows: a. b. c. Phase I: Primer axis horizontal Phase II: Primer axis vertical, primer stock down Phase III: Primer axis vertical, primer stock up The primer shall be marked with a line in the axial direction at the junction of the stock and tube indexi

48、ng their initial relative position, in order to determine the integrity after vibration. The primer shall be rigidly mounted to the vibration table at the primer stock. After vibration, the primer shall be subjected to the tests of 4.7.4 and 4.7.5. 4.7.7 Ballistics. The primer shall be assembled int

49、o 5“/38 caliber full service propelling charge assembly in accordance with Drawing 2847233. All components shall be service acceptable lots. The propellant shall be conditioned at 90 & 15F for 24 hours minimum prior to assembly of the propelling charge. All other components shall be conditioned at 85 +. 20F for 24 hours minimum prior to assembly of the propelling charge. The assembled propelling charge shall be conditioned at 8 Licensed by Information Handling Services, b MIL-P-187LbC 13 = 99999Ob 0473304 O MIL-P-18716C 90 & 5F for 48 hours minimum immediately prior to f