NAVY MIL-P-16789 D-1986 PUMPS (INCLUDING PRIME MOVERS AND SUPPORT ITEMS) PACKAGING OF《(包括原动机和支持组件)泵的包装》.pdf

《NAVY MIL-P-16789 D-1986 PUMPS (INCLUDING PRIME MOVERS AND SUPPORT ITEMS) PACKAGING OF《(包括原动机和支持组件)泵的包装》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-P-16789 D-1986 PUMPS (INCLUDING PRIME MOVERS AND SUPPORT ITEMS) PACKAGING OF《(包括原动机和支持组件)泵的包装》.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-P-Lb787D PA m 7777706 0283753 8 m MIL-P-l6789D(SH) 30 October 1986 SUPERSEDING MIb-P-l6789C(SH) 10 September 1974 (See 6.9) MILITARY SPECIFICATION PUMPS (INCLUDING PRIME MOVERS AND SUPPORT ITEMS); PACKAGING OF This specifisation is approved for use within the Naval Sea Systems Command, Departmen

2、t of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for packaging (preservation, packing and marking) of pumps; reciprocating, centrifugal, axial flow, positive displacement, oxygen, hydr

3、aulic, prime movers, and associated support items (see 6.1). 1.2 Levels of protection. 1.2.1 Preservation. Level A (see 3.8.1.1) Level C (see 3.8.1.2) Commercial (see 3.8.1.3) 1.2.2 Packing. Level A (see 3.9.1.1, 3.9.2.1, table II and 3.9.2.1.1.1) Level B (see 3.9.1.1, 3.9.2.1, table II and 3.9.2.1.

4、1.2) Level C (see 3.9.1.1, 3.92.1, table II and 3.9.2.1.1.3) Commercial (see 3.9.2.2) 2. APPLICABLE DOCUMENTS 2.1 Government documents. Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander,

5、 Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document or by letter. Improvement Proposal (DD Form 1426) appearing at the end of this document AMSC N/A AREA PACK DISTRIBUTION STATEMENT A Approved for public release

6、; distribution unlimited r THIS DOCUMENT CONTAINS 3 7 PAGES. 1. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-2.1.1 Spcifications and standaxds. The following specifications and standards form part of this specification to the extent specif led her

7、ein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (BoDISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL L-P-378 - Plastic Sheet and Strip, Thin Gauge, Polyo

8、lefin. P-D-680 - Dry Cleaning Solvent. NN-P1530 - Plywood, Flat Panel. TT-T-291 - Thinner, Paint, Mineral Spirits, Regular and Odorless. UU-P268 - Paper, Kraft, Wrapping. LLL-B-810 - Building Board, (Hardboard) Hard Pressed, Vegetable PPP-B-566 - Boxes, Folding, Paperboard. PPP-B-S76 - Boxes, Wood,

9、Cleated, Veneer, Paper Overlaid. PPP-B-S85 - Eoxes, Wood, Wirebound. PPP-B-591 - Boxes, Shipping, Fiberboard, Wood-Cleated. PPP-B-601 - Boxes, Wood, Cleated-Plywood. PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner. PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-B-640 - Boxes, Fiberboard, Corrugated, T

10、riplemWall. PPP-B-665 - Boxes, Paperboard, Metal Edged and Components. PPP-B-676 - Boxes, Setup. PPB-B-1055 - Barrier Material, Waterproofed, Flexible. PPF-B-1672 - Boxes, Shipping, Reusable with Cushioning. PPP*C-795 - Cushioning Material, Flexible, Cellular, Plastic Film for Packaging Applications

11、. PPP-C443 - cushioning Material, Cellulosic. PPP-C450 - Cushioning Material, Polystyrene, Expanded, Resilient PPP-C-1120 - cushioning Material, Uncompressed Bound Fiber for PPP-C-1752 - Cushioning Material, Packaging, Unicellular Poly- PPP-C-1797 - Cushioning Material, Resilient, Low Density, Unice

12、l- PPP-C-1842 - Cushioning Material; Plastic, Open Cell (For Packaging PPP-F-320 - Fiberboard; Corrugated and Solid, Sheet Stock (Con- PPP-11-1581 - Hardware (Fasteners and Related Items), Packaging of. PPP-P40 - Packaging and Packing of Hand Tools. PPP-P291 - Paperboard, Wrapping and Cushioning. PP

13、P-Ta60 - Tage: Packaging, Waterproof. Fiber. (For Packaging Uses). Packaging. ethylene Foam, Flexible. lular, Polypropylene Foam. Applications). tainer Grade), and Cut Shapes. MILITARY MIL-Vu3 - Valves, Fittings, and Flanges (Except for Systems Indicaced Herein); Packaging of. MIL-G-104 - Crates, Wo

14、od; Lumber and Plywood Sheathed, Nailed and Bolted. NIL-P116 - Preservation, Mechods of. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. MIL-P-Lb789D PA W 7797706 0283755 L W MIL-P-l6789D(SH) MILITARY (Continued) MIL-B-121 - Barrier Material, Gre

15、aseproofed, Waterproofed, Flexible. MIL-P-149 - Plastic Coating Compound, Strippable (Hot-Dripping). MIL-R-196 - Repair Parts, Accessories, and Kits, Mechanical; MIL-B-197 - Bearings, Antifriction; Associated Parts and Sub- MIL-B-233 - Boxes, Repair Parts, Storage. MIL-P-775 - Packaging of Hose, Hos

16、e Assemblies; Rubber, Plastic, Packaging of. assemblies; Preparation for Delivery of. Fabric, or Metal (Including Tubing); and Fittings, Nozzles, and Strainers. or Cushioning Pads). MIL-B-3106 - Board, Composition, Water-Resistant, Solid (For Filler MIL-C-3774 - Crates, Wood; Open 12,000- and 16,000

17、- Pound Capacity. MIL-C-4150 - Cases, Transit and Storage, Waterproof and Water- MIL-P-4861 - Packing, Preformed, Rubber, Packing: Packaging of. MIL-R-5001 - Rubber Cellular Sheet, Molded and Hand Built Shapes; MIL-C-5584 - Containers, Shipping and Storage, Metal Reusable. MIL-D-6054 - Drum, Metal-S

18、hipping and Storage. MIL-D-6055 - Drums, Metal, Reusable Shipping and Storage (Cap. from MIL-H-6083 - Hydraulic Fluid, Petroleum Base, For Preservation and MIL-R-6130 - Rubber, Cellular, Chemically Blown. MIL-1-8574 - Inhibitors, Corrosion, Volatile, Utilization of. MIL-C-9897 - Crates, Slotted Angl

19、e, Steel or Aluminum, For Light- Vaporproof. Latex Foam. J 88 to 510 Cubic Inches). Operation. weight Airframe Components and Bulky Items (For Maxi- mum Loads of 3000 Pounds). MIL-E-10062 - Engine Preparation for Shipment and Storage of. MIL-V-13811 - Varnish, Waterproofing, Electrical, Ignition. MI

20、L-C-15074 - Corrosion Preventive, Fingerprint Remover. MIL-C-15348 - Cleaning Oil, Turbine (Compounded). MIL-C-16173 - Corrosion Preventive Compound, Solvent Cutback, Cold-Application. MIL-E-16298 - Electric Machines Having Rotating Parts and Asso- ciated Repair Parts: Packaging of. MIL-P-17286 - Pr

21、opulsion and Auxiliary Steam Turbines and Gears (Including Repair Parts, Tools, Accessories and Instruments): Packaging of. Service. Shipboard. and Repair Parts; Packaging and Packing of. MIL-L-17331 - Lubricating Oil, Steam Turbine andGear, Moderate MIL-E-17341 - Engines, Gas Turbine, Propulsion an

22、d Auxiliary Naval MIL-E-17555 - Electronic and Electrical Equipment, Accessories, MIL-H-17672 - Hydraulic Fluid, Petroleum, Inhibited. MIL-H-19457 - Hydraulic Fluid, Fire-Resistant, Non-Neurotoxic, MIL-P-19644 - Plastic Molding Material (Polystyrene Foam, Expanded MIL-R-20092 - Rubber Sheets and.Ass

23、embled and Molded Shapes, Cellu- Bead). lar, Synthetic, Open Cell (Foamed Latex). 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-PIILITARY (Continued) NIL-L-21260 MIL-D-22019 MIL-B-22820 PIIL-1-22110 NIL=B-22191 MIL-1-24092 NIL-1-24453 HIL-P=2 Wit

24、h Appropriate Test Methods. gen Gas Piping Systems. Program Requirements (For Systems and Equipments). 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MILITARY (Continued) MIL-STD-2073-1 - DOD Materiel Procedures for Development and Application of

25、Packaging Requirements. MS90363 - Box, Fiberboard with Cushioning for Special Mini- mum Cube Storage and Limited Reuse Applications. (Copies of specifications and standards, required by contractors in connec- tion with specific acquisition functions should be obtained from the contracting activity o

26、r as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDISS specified in th

27、e solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. AMERICAN NATIONAL STANDARDS INSTITUTE (ANSI) MH15.1 - Glossary of Packaging Terms. (Application for copies

28、should be addressed to the American National Standards Institute, 1430 Broadway, New York, NY 10018.) AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) D 996 - Standard Terminology of Packaging and Distribution D 3951 - Standard Practice for Commercial Packaging. Environments. (DoD adopted) (Applica

29、tion for copies should be addressed to the American Society for Testing and Materials , 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may b

30、e available in or through libraries or other informational services. ) 2.3 Order of precedence. When an equipment or item is acquired in conform- ance with a commodity specification having detailed packaging or preparation for delivery requirements which differ from this specification, the packaging

31、 or preparation for delivery specified in the commodity specification shall apply. 3. REQUIREMENTS 3.1 Definitions or explanation of packaging terms. Definitions or explana- tions of packaging terms applicable.to this specification shall be as stated in the applicable referenced specification and 6.

32、4. For definitions or explanation of packaging terms not specified therein, ANSI MH15.1 and ASTM D 996 shall apply. 3.2 First article. When specified in the contract or purchase order, a sample shall be subjected to first article inspection (see 4.4.1 and 6.3). 5 Provided by IHSNot for ResaleNo repr

33、oduction or networking permitted without license from IHS-,-,-3.2.1 -. When specified (see 6.2.1), a dummy or simulated load may be used for rough handling tests (see 4.4.2). When a dummy or simulated load is substituted for the actual equipment or item in performing tho rough handling tests, instru

34、mentation of the pack is required for assurance that the acedoration of the packed item during the tests is less than the fragi- lity rating of tho item. The details of the instrumentation including location ahall bo included with the test results (see 4.4.3). When specified in the contract ox order

35、, notification of tests shall be prepared (see 6.2.2). 3.3 Materials. The materials shall be as specified herein and in the applicable referenced specifications. 3.3.1 Recovered m-. Unless otherwise specified herein, all equip- ment, mnterial, and articles incorporated in the products covered by thi

36、s speci- fication aha11 be new and may be fabricated using materials produced from recovosed materials to the maximum extent practicable without jeopardizing the intended use. The term “recovered materials“ means materials which have been collected or rocovered from solid waste and reprocessed to be

37、come a source of raw materials, as opposed to virgin raw materials. None of the above shall be intarpseted to mean that the use of used or rebuilt products is allowed under this specification unless otherwise specifically specified. 3.3.2 New materials. The use of newly developed packaging materials

38、 or procedures are encouraged and recommended and will be permitted under the condi- tions spocifiad herein, provided they are equal to or better than the specified materials or procedures. 3.3.2.1 Certification of alternate materials. When specified in the con- tract or order, a certificate of comp

39、liance shall be prepared, if the contractor desires to use alternate materials or procedures other than those specified heroin (see 6.2.2). 3.3.3 Asbestos, (See 6.5) 3.3.3.1 Packagingmatea. Asbestos or material and items containing asbestos shall not be used in the packaging of material or items cov

40、ered by this specification (seo 6.5). 4.3.3.2 Packaged items. Asbestos and separately packaged components con- taining asbestos that is predominately distributed throughout the item, shall be packaged in sealed, dust and siftproof packages. Flexible packages shall be heat sealed. Packages shall be m

41、arked as specified (see 3.9.3). 3.3.3.3 P-10 grade 30 P-7, P-10 grade 30 P-2, P-10 grade 30 “ “ “ “ “ “ P-2 P-2 “ “ P-7, P-10 “ “ “ “ “ . “ 11 External P-2 “ “ “ “ P-7, P-10 grade 30, P- 18 P-7, P-10 grade 30, P- 18 P-2, P-10 grade 30 P- 18 P-2, P-18 P-2, P-18 “ P-2, P-18 “ P-2 P-2, P-18 “_ “ P-7, P

42、-10 “ P-2, P-18 P-19 or MIL-P- 149 Type 11 Y “ “ “ Special remarks (see note 8) See 3.8.1.1.1.3.4 Use MIL-P-4861 See note 5 Use PPP-H-1581 “ See 3.8.1.1.6.2.1 See 3.8.1.1.6.2.1 “ See 3.8.1.1.6.2.1 See 3.8.1.1.6.2.1 See 3.8.1.1.6.2.1 “ See 3.8.1.1.6.2.1 “ “ See 3.8.1.1.6.2.1 See 3.8.1.1.1.3.3.3 See n

43、ote 2 See note 5 See note 2 See note 4 “ and 3.8.1.1.6.2.1 See bearing: friction sleeve “ Use MIL-E-17555 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-Item MLL-P-lb7BSD PA U 997490b 02839611 MIL-P-l6789D(SH) Ferrous Non-ferrous Flat; (packing) G

44、arter (packing) Coil Spring TQOS, tool kits (hand) Valves J f ttings , and flanges Vano, diffuser TABLE I. Ppservation. - Continued Method of preservation I III IC IC I -1“ “I“ I, IC, or IB T Applicable type of preservative MIL-P-116 Internal P-2, P-10 11“ “ External . P-2, P-10 P-18 “ I “ - P-18, P

45、-19 “1“ P-2, P-18, P-19, or Type 11 , MIL-P- 149 am Special remarks (see note 8) See 3.8.1.1.6.2.1 1-11 1-11 See 3.8.1.1.6.2.1 See 3.8.1.1.7 and MIL-T-45542 Use MIL-V-3 See notes 2, 3, and 4 Notas : 1. Unless otherwise specified (see 6.2.1), preserve in accordance with 2. Cushioning shall be applied

46、 to protect item from damage. d. Preserved items shall be wrapped with greaseproof barrier material 4. Contact presorvative shall be applied to items preserved by method !i. Provide protection against deformation. 6. When packaged in multiples, items shall be dusted with talc, talcum or soapstone po

47、wder (see 3.3.3.3) 7. Preservative shall be applied eo unpainted surfaces only. The interior sf unit shall be completely drained following cleaning. The drain plugs, if applicable, shall be replaced. 3.8.1.1.1.3.3. prior to application of cushioning materials. IB-2 8. Reusable containers for spares

48、(repairable) (see 3.8.1.1.6.10). 3.8 Level of protection. (See 6.4.1). 3.8.1 Freservatioq. Preservation (unit protection) shall be level A, C or commercial as specified (see 6.2.1). 3.8.1.1 Levell. Unless otherwise specified herein, cleaning, drying, preotle, and methods of preservation (unit protec

49、tion), shall be in accor- dence with MIL-Pm116 and table I herein. Table I applies eo processing of supply support material (spares and repair parts), accessories, and tools, Requirements in table f are assigned by category; methods are assigned on the basis of the typo of unit protection most commonly required for a specific item. Unless therwisa specified (see 6.2.1), selection of the submethod under a particula