NAVY MIL-DTL-82968-1998 CUTTER EXPLOSIVE ACTUATED MK 33 MOD 0《0系数33型爆炸驱动刀具》.pdf

《NAVY MIL-DTL-82968-1998 CUTTER EXPLOSIVE ACTUATED MK 33 MOD 0《0系数33型爆炸驱动刀具》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-82968-1998 CUTTER EXPLOSIVE ACTUATED MK 33 MOD 0《0系数33型爆炸驱动刀具》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 MIL-DTL-82968 = 9999906 2083588 37T a I INCH-POUND I MIL-DTL-82968( OS) 23 September 1998 DETAIL SPECIFICATION CUTTER, EXPLOSIVE ACTUATED, MK 33 MOD O This specification is approved for use by Naval Sea Systems Command, Department of the Navy, and is available for use by all Departments and Agencie

2、s of the Department of Defeizsc 1. SCOPE 1.1 Scope. This specification covers the requirements for the manufacture and acceptance of the MK 33 MOD O Explosive Actuated Cutter. 2. APPLICABLE DOCUMENTS 2.1 General. The documents listed in this section are specified in sections 3 and 4 of this specific

3、ation. This section does not include documents cited in other sections of this specification or recommended for additional information or as examples. While every effort has been made to ensure the completeness of this list, document users are cautioned that they must meet all specified requirements

4、 documents cited in sections 3 and 4 of this specification, whether or not they are listed. 2.2 Government documents. 2.2.1 Specifications, standards, and handbooks. The foilowing specifications, standard, and handbooks form a part of this document to the extent specified herein. Unless otherwise sp

5、ecified, the issues of these documents are those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPECIFICATIONS FEDERAL RR-W-410 Wire Rope and Strand Beneficial comments (recommendations, add

6、itions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Commander, Indian Head Division, Naval Surface Warfare Center, Standardization Team (Code 840M), 101 Strauss Avenue, Indian Head, MD 20640-5035, by iisiiig the Standardization Document im

7、provement Proposal (DD Form 1426) appearing at the end of this document or sending a letter. AMSC NIA FSC 1377 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- NIL-DTL-

8、2968 9999906 2083589 206 MIL-DTL-S296S(OS) STANDARDS MILITARY MIL-STD-33 1 MIL-STD-8 1 O Fuze and Fuze Components, Environmental and Performance Test for Test Method Standard for Environmental Engineering Considerations and Laboratory Tests DOD-STD-2 1 O 1 Classification of Characteristics 2.2.2 Oth

9、er Government documents, drawings, and publications. The following other Governmental documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. DRAWINGS NAVAL SEA SYSTEMS COMMAND (CAG

10、E Code 5371 1) DL 6784468 6570660 657066 1 6702805 Cutter, Explosive Actuated, MK 33 Mod O Detonator, Non-Electric (Single) Detonator, Non-Electric (Dual) Initiator, Pyrotechnic Lead (Copes of other Government documents, drawings, and publications required by contractors in connections with specific

11、 acquisition functions should be obtained from or as directed by the contracting officer). 2.3 Non-Government publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DoD adopted are thos

12、e listed in the issue of the DoDISS cited in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS are the issues of the documents cited in the solicitation (see 6.2). AMERICAN SOCIETY FOR “G AND MATERIALS (ASTM) ASTM E 1 742 Standard Practice for Radiographi

13、c Examination (Application for copies should be addressed to the American Society for Testing and Materials Customer Service, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959.) 2.4 Order of Precedence. In the event of a conflict between the text of this document and the references cited herei

14、n (except for associated specifications or specification sheets), the text of the document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 2 Provided by IHSNot for ResaleNo reproduction or networking permi

15、tted without license from IHS-,-,-MIL-DTL-82968 E 999990b 2083590 T28 II MIL-DTL-82968( OS) 3. REQUIREMENTS 3.1 Item definition. The MK 33 MOD O Explosive Actuated Cutter (cutter )(see 6.7.1) is approxiinately 9 inches long and 2.88 inches wide at its cutting base. The cutter weighs approximately 5

16、pounds in air and 4 pounds in water. The cutter consists of a body assembly, a safety block, and two cavities for Detonators. The external surfaces are black (see 3.3). The cutter is capable of being operated under water pressure of 28 psig to completely sever a one inch diameter plow steel wire rop

17、e. 3.2 First article inspection. When specified (6.2), a sample shall be subjected to first article inspection in accordance with 4.2. 3.3 Conformance to documents. The MK 33 Mod O Explosive Actuated Cutter covered by this specification shall be manufactured in accordance with DL 6784468 and all doc

18、uments listed thereon. 3.4 Materiais. All materials used in the manufacture of the cutters shall conform strictly to the specifications referred to on the respective drawings unless specific approval in writing covering a departure therefrom, has been obtained from the cognizant Navy design activity

19、 prior to manufacture. When alteniate material or methods of manufacture are specified on the drawings, the bidders selections shall be clearly stated in the proposal. 3.5 Cutter inspection. 3.5.1 Pin assembly. Following assembly of the cutter blade and pin, the cutter blade edge shall rest securely

20、 within the notch of the pin (see 4.4.1). 3.5.2 Environmental requirements. 3.5.2.1 Transportation vibration. The cutter shall meet all acceptability requirements after being subjected to transportation vibration testing (see 4.4.4.1). 3.5.2.2 Salt fog. The cutter shall meet all acceptability requir

21、ements after being subjected to the salt fog test (see 4.4.4.2). 3.5.2.3 Rough handling drop-test. The cutter shall meet all acceptability requirements after being subjected to the rough handling drop-test (see 4.4.4.3). 3.5.3 Radiographic requirements. The cutters shall be free of imperfections whe

22、n radiographed (see 4.4.2). 3.5.4 Ballistic requirements. The cutter shall meet ballistic requirements when subjected to the test prescribed by 4.5.1. The cutter shall be capable of being operated under water to completely sever it one inch diameter plow steel wire rope (see 4.5.2). The one inch dia

23、meter wire rope shall be Type I, Class 2, Construction 2 (6 x 19 Warrington) or Construction 3 (6 x 19 Seale), IWRC (Independent wire-rope core) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-829b M 990b 2083593 9bY O Examinations and Test

24、s MIL-DTL-S296S(OS) - Sample 12 3 4 5 6 7 8 9 1011 12 6 X 7 wire rope with wire-strand core, improved plow steel, uncoated, preformed in accordance with Federal Specification RR-W-410. 3.6 Workmanship. The cutter shall be free of the following defects: poor or incorrect markings, bum, dents, rust, c

25、orrosion, scratches to the black coating, damaged O-rings, chips, dirt, or other defects which could adversely affect ballistic performance. Any cleaning methods shall not be injurious to any of the components nor shall components be contaminated by cleaning agents employed. There shall be no chemic

26、al or electro-chemical corrosive or deteriorative effects from the manufacturing process. 4. VERIFICATION 4.1 Classification of inspections. The inspections herein are classified as follows: a. First article inspection (see 4.2). b. Quality conformance inspection (see 4.3). 4.2 First article inspect

27、ion. Unless otherwise specified in the contract or purchase order (see 6.2), first article inspection shall consist of the tests and examinations listed in table I. The first article inspection shall be performed on sample units which have been produced using the same materials, equipment, processes

28、 and procedures as will be used in regular production. Ali parts and materials, including packaging and packing shall be the same as will be used for regular production and shall be from the intended sources of supply. Any quantity production prior to notification by the contracting agency of the fi

29、rst article sample acceptdbility will be at the contractors risk. TABLE I. First article Tests. Visual Examination (3.3,3.4,3.6,4.2,4.4.3) Radiographic Examination (4.4.2) Pin Assembly (4.4.1) Transportation Vibration Test (4.4.4.1) Salt Fog Test (4.4.4.2) Rough Handling Drop Test (4.4.4.3) Function

30、 Test (4.5.1) Retain Samples xxxxx xxxx x x x xxxxx xxxx x x x xxxxx xxxx x x x xxx xx xx xx x xxxxx xxxx x xx 4.2.1 Sample size. The first article sample size shall consist of twelve (12) assembled cutters, nine (9) sets of unassembled parts, and one (1) set of unassembled parts without coating or

31、final protective finish. The sample shall be manufactured in the same manner, using the same materials, equipment, processes, and 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-82968 M 9999906 2083592 8TO E MIL-DTL-82968( OS) procedures a

32、s used in regular production. After inspection and provisional acceptance at source, the first article sample shall be inspected for all requirements of the drawing and specifications. The Government reserves the right to require new fmt article samples until an acceptable sample is submitted (see 6

33、.5). 4.2.2 Inspection routine. Ten (10) cutters shall be expended in the tests listed in Table I and two (2j shall be retained for investigative purposes. 4.2.3 Faiiure. Failure of the sample to meet the requirements of 3.3 through 3.6 shall be cause for rejection of the first article sample. 4.3 Qu

34、aiity conformance inspection. Quality conformance inspection shall consist of verification of the cutter characteristics and requirements of DL 6784468 and the tests and examinations of Table II. TABLE II. quality Conformance Tests and Examinations. Item Nature of Test Requirement Test Classificatio

35、n (DOD-STD-2 101) Cutter Visual Examination 3.6 4.4.3 (M101) Cutter Radiographic Examination 3.5.3 4.4.2 Cutter Pin Assembly 3.5.1 4.4.1 (M102) Cutter Ballistic Requirements 3.5.4 4.5.1 (M103) Cutter Preservation-packaging, 5.1 4.4.3 (M 104) Packing and Marking 4.3.1 Lot size. Unless otherwise speci

36、fied (see 6.2), the production lot size shall be not less than 2 and not greater than 3000. Cutters required for all test purposes shall be selected from the production lot and :;hall not be applied as part of the quantity specified for delivery by the contract. 4.3.2 Sampling. A sample of cutters f

37、or ballistic test shall be selected from each production lot in accordance with table ilI. In addition to the sample of cutters for ballistic test, two (2) additional cutters shall be furnished from each production lot to be retained for investigative purposes. 4.3.3 Classification of characteristic

38、s. The Characteristics verified by the tests and examinations herein are classified as critical, major, or minor in accordance with DOD-STD-2101. Tests and examinations that verify critical characteristics are identified by the symbol (C) and major characteristics by the symbol (M). 5 Provided by IH

39、SNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-82968( OS) Lot Size 20 - 500 501 - 1000 1001 - 1500 1501 - 2000 2001 - 2500 The number following the classification symbol indicates the serial number of the test or examination. Tests and examinations which

40、are not annotated with a classification code are classified minor. Sample Size Retained Sample 10 2 15 2 20 2 25 2 30 2 TABLE IIi. Ouality Conformance Samde Size. 4.4 Test. 4.4.1 Pin assembly inspection. One hundred percent examination after cutter blade and pin assembly shall demonstrate that the c

41、utting edge of the cutter blade is resting in a seated position within the notch in the pin. An assembly wherein the cutting edge of the cutter blade is not in seated position within the pin notch shall be considered defective. Cutters that fail to meet the requirements of 3.5.1 are defined as defec

42、tive. 4.4.2 Radiographic examination. All first article and lot acceptance test samples shall be radiographically examined in accordance with ASTM-El742. Any observable imperfections in components or assembly shall be cause for rejection. If any assembly or component defects are noted, the contracto

43、r shall 1 O0 percent X-ray the represented lot and submit the radiographs to the design activity for review. The cutters shall be positioned for the most revealing view with the long axis perpendicular to the x-ray beam. The radiographs shall be in consecutive order and each radiograph shall carry a

44、 permanent identification of the cutters displayed thereon. The radiograph identification shall include item nomenclature, the complete lot number, contract number and complete span of test control numbers displayed thereon. Any missing test control numbers shall be identified on the radiograph. If

45、radiographs of the entire production lot are required they shall be at the expense of the contractor. Defective assemblies found during radiographic review shall be removed from the production lot. 4.4.3 Visual examination. Aii cutters shall be visually examined. Cutters having any of the defects of

46、 3.3, 3.4,3.5.1, and 3.6 shall be rejected. The preservation-packaging, packing, and marking of the cutter shall be examined for conformance to section 5. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- MIL-DTL-82968 9 9999906 2083594 b73 b 4.4.4

47、Environmental tests. 4.4.4.1 Transportation vibration test. The cutters, enclosed within their shipping containers, shall be subjected to transportation vibration test B2 of MIL-STD-331 at 23 & 10 “C. Defectives are cutters that fail to meet the requirements of 3.5.2.1. 4.4.4.2 Salt fog test. The cu

48、tters, outside of their shipping containers, shall be subjected to a forty-eight hour salt fog test defined in MIL-STD-810, Test Method 509.3. After completion of the test, the cutttn shall meet the requirements of 3.3 through 3.5. Defectives are cutters that fail to meet the requirements of 3.5.2.2

49、. 4.4.4.3 Rough handhg drop test, The unpacked cutter shall be dropped, in random orientations, onto a non-yielding surface. Four drops from 36 inches and eight (8) drops from 18 inches. Defectives are cutters that fail to meet the requirements of 3.5.2.3 4.5 Ballistic tests. 4.5.1 Function test. The cutter shall be functionally tested in a suitable open tank capable of holding at least three feet of water. The tank shall include internal means