NAVY MIL-DTL-24441 35 B-2009 PAINT EPOXY-POLYAMIDE RED FORMULA 156 TYPE IV《IV型配方156红色环氧树脂聚酰胺油漆》.pdf

《NAVY MIL-DTL-24441 35 B-2009 PAINT EPOXY-POLYAMIDE RED FORMULA 156 TYPE IV《IV型配方156红色环氧树脂聚酰胺油漆》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-DTL-24441 35 B-2009 PAINT EPOXY-POLYAMIDE RED FORMULA 156 TYPE IV《IV型配方156红色环氧树脂聚酰胺油漆》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 METRIC MIL-DTL-24441/35B(SH) 27 August 2009 SUPERSEDING MIL-DTL-24441/35A(SH) 19 May 1999 DETAIL SPECIFICATION SHEET PAINT, EPOXY-POLYAMIDE, RED, FORMULA 156, TYPE IV This specification is approved for use by the Naval Sea Systems Command, Department of the Navy, and is available for use by all Dep

2、artments and Agencies of the Department of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-24441. FORMULA: This formula covers red epoxy-polyamide paint designated Navy Formula 156, Type IV for interior or exterior use. The p

3、aint shall consist of the ingredients specified in the quantities specified. Component A14/Ingredients Kilograms Pounds Thixatrope1/ - - Polyamide2/ 16.33 36.0 Polyamide adduct3/ 165.56 365.0 Titanium dioxide4/45.36 100.0 Magnesium silicate5/ 90.72 200.0 Butyl alcohol6/117.03 258.0 Yellow iron oxide

4、8/ 22.68 50.0 Red iron oxide7/136.08 300.0 Component B14/Ingredients Kilograms Pounds Thixatrope9/ - - Epoxy resin10/265.81 586.0 Magnesium silicate5/ 90.72 200.0 Naphtha11/ 97.52 215.0 Aluminum silicate12/ 68.04 150.0 See footnotes on last page. AMSC N/A FSC 8010 Provided by IHSNot for ResaleNo rep

5、roduction or networking permitted without license from IHS-,-,-MIL-DTL-24441/35B(SH) QUANTITATIVE REQUIREMENTS: The paint shall meet the following quantitative requirements and the qualitative requirements of section 3 of the general specification. The components A and B shall be mixed 1:1 by volume

6、 for mixed component tests. Tests shall be performed in accordance with the general specification. Component A Component B Mixed components Requirements Min Max Min Max Min Max Pigment content, percent (%) 48.0 54.0 28.0 33.0 - - Volatiles, % 24.0 29.0 17.0 22.0 - - Nonvolatile vehicle, % 17.5 23.5

7、48.0 53.0 - - Water, % - 1.5 - 0.5 - - Coarse particles, % - 0.3 - 0.3 - - Consistency, grams - 310 - 410 - - Kilograms per liter (kg/L) (pounds per gallon (lb/gal) 1.43 (11.9) 1.58 (13.2) 1.26 (10.5) 1.38 (11.5) - - Set to touch, hours a. at 4.4 C (40 F) - - - - - 3 b. at 23 C (73 F) - - - - - 3 Dr

8、y-hard, hours a. at 4.4 C (40 F) - - - - - 24 b. at 23 C (73 F) - - - - - 8 Fineness of grind, NS 4 - 4 - - - Flash point, C (F) 35.6 (96) - 37.8 (100) - 35.6 (96) - Titanium dioxide, % of pigment 13 - - - - - Pot life, hours at 23 C (73 F) - - - - 4 - Sag resistance, micrometers (mils) - - - - 300

9、(12) - Color of dry film to approximate the standard color chip - - - - Conform Weight per epoxy vehicle - - 175 195 - - Contrast ratio, 3-mil dry film thickness - - - - 0.98 - Gloss, 60 degree specular, % - - - - - 25 VOC, grams per liter (g/L) (lb/gal) - - - - - 340 (2.8) See footnotes on next pag

10、e. 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-24441/35B(SH) 3 1/Thixatrope to be used is the manufacturers choice. In the development of component A, 6.80 kilograms (15 pounds) (7.95 liters (2.1 gallons) of Disparlon NS-30 made by King

11、 Industries were used. Manufacturer is responsible for choosing a thixatrope that meets all the requirements herein, including shelf life. Thixatrope is a pigment for calculation purposes.2/GENAMID 2000, Cognis Corp.; ANCAMIDE 507, Air Products Chemical Corp.; EPOTUF SF7791, REICHHOLD Chemical. 3/Ar

12、adur 283, Huntsman Advanced Materials. 4/Titanium dioxide conforming to ASTM D476, Type IV. In the development of component A, DuPont Tipure R960 was used.5/ Nicron 503, Luzenac, Inc.6/Butyl alcohol conforming to ASTM D304. 7/Red Iron Oxide RO-6097 or RO4097, Elementis Pigments.8/Yellow Iron Oxide Y

13、O-3587, Elementis Pigments; Yellow Iron Oxide YLO3288D, Rockwood Pigments.9/ Thixatrope to be used is the manufacturers choice. In the development of component B, 6.80 kilograms (15 pounds) (6.81 liters (1.8 gallons) of Disparlon 6500 made by King Industries were used. Manufacturer is responsible fo

14、r choosing a thixatrope that meets all the requirements herein, including shelf life. Thixatrope is a pigment for calculation purposes.10/ EPON 828, Hexion Chemical Co.; ARALDITE 6010, Huntsman Advanced Materials; DER 331, Dow Chemical Corp.; EPO-TUF 37-140, REICHHOLD Chemical Corp.11/ Conforming to

15、 ASTM D3734, Type I. In the development of component B, AMSCO Super High Flash Naphtha was used.12/ Huber 70C, J.M. Huber Corp.; Satintone #1, Englehard Mineral and Chemical Co.13/ Use FED-STD-595 color chip number 20152. Color shall approximately match the color chip.14/ For VOC calculations, compo

16、nent A makes approximately 383 liters (101 gallons) and component B makes approximately 386 liters (102 gallons).Use of alternate ingredients in this formula must have prior approval of the Naval Sea Systems Command. Approval will be based on review of data demonstrating equivalent physical, chemica

17、l and performance characteristics of paint manufactured with the proposed alternate material and the requirements as specified in 3.4.1 of MIL-DTL-24441. Paint incorporating the proposed alternate ingredient shall conform to all the requirements of this military specification sheet and the general s

18、pecification. CHANGES FROM PREVIOUS ISSUE: Marginal notations are not used in this revision to identify changes with respect to the previous issue due to the extent of the changes. Preparing Activity Navy SH (Project 8010-2009-019) NOTE: The activities listed above were interested in this document a

19、s of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at http:/assist.daps.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-