NAVY MIL-C-3735 E-1988 CUFFS KNIT WRIST AND ANKLE AND CLOTH KNITTED《密织布料手腕和脚踝包覆》.pdf

《NAVY MIL-C-3735 E-1988 CUFFS KNIT WRIST AND ANKLE AND CLOTH KNITTED《密织布料手腕和脚踝包覆》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-C-3735 E-1988 CUFFS KNIT WRIST AND ANKLE AND CLOTH KNITTED《密织布料手腕和脚踝包覆》.pdf（25页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-C-3735E 3 7777706 0374263 T U - IINCH-POUNDI MIL-C-3735E 30 November 1988 SUPERSEDING 25 October 1982 MIL-C-3735D MILITARY SPECIFICATION CUFFS, KNIT, WRIST AND ANKLE, AND CLOTH, KNITTED . This specification is approved for use by all Departments and Agencies of the Department of Defense. 1. SCOP

2、E i * 1.1 Scope. This specification covers the requirements for ankle and wrist cuffs knitted to shape and for knitted fabrics for making ankle and wrist cuffs, waistbands, balaclavas and collars. * 1.2 Classification, The knitted cuffs and cloth shall be procured in the following types, classes and

3、 sizes as specified (see 6.2): Type I - Wool Class 1 - Cuffs, ankle, 1 x 1 rib Class 2 - Cuffs, wrist, 1 x 1 rib Size 1 - 8 inches Size 2 - 8 3/4 inches Class 3 - Cloth, knitted; for ankle and wrist cuffs, waistbands and Class 4 - Cloth, knitted; for balaclavas, 1 x 1 rib collars, 1 x 1 rib Type III

4、 - Polyester Class 2 - Cuffs, wrist, 1 x 1 rib Size 2 - 8 31?4 inches Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, 21 Strathmor

5、e Road, Natick, MA 01760-2490 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC 8315 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. _ 7 THIS DOCUMENT CONTAINS 85

6、 PAGES. _ - r Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-_ _ _I- MIL-C-3735E 3 = 999990b 03742bll li = MIL-C-3735E Type IV - Aramid Class 1 - Cuffs, ankle, 1 x 1 rib Class 2 - Cuffs, wrist, 1 x i rib Size 2 - 8 3/4 inches Class 3 - Cloth, knitte

7、d; for ankle cuffs and waistbands, 1 x 1 rib 2. APPLICABLE DOCUMENTS * 2.1 Government documents. * 2.1.1 Specifications, standards, and handbooks. The following specifications, standards, and handbooks form a part of this specification to * the extent specified herein. Unless otherwise specified, th

8、e issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. I SPECIFICATIONS FEDERAL NN-P-7 1 PPP-B-636 PPP-T-45 MILITARY MIL-P-15011 HIL-B-17757 MIL-C-43665 STANDARDS FE

9、DERAL FED-STD-191 MILITARY MIL-STD-105 MIL-STD-129 MIL-STD-147 MIL-STD-1491 Pallets, Material Handling, Wood, Stringer Boxes, Shipping, Fiberboard Construction, 2-Way and 4-Way (Partial) Tape, Gummed, Paper, Reinforced and Plain, for Sealing and Securing Pallets , Material Handling, Wood , Post Cons

10、truction, 4-Way Entry Boxes, Shipping, Fiberboard (Modular Sizes) Cloth, Wool: Mothproofing Treatment of Textile Test Methods Sampling Procedures and Tables for Inspection by Marking for Shipment and Storage Palletized Unit Loads Glossary of Knitting Imperfections Attributes (Copies of specification

11、s, standards, drawings, and publications required by contractors in connection with specific procurement functions should be 2 _ - - Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3735E 3 m 997970b 037q265 3 MIL-C-3735E obtained from the procu

12、ring activity or as directed by the contracting officer. ) * 2.1.2 Other Government documents, drawings, and publications. The following other Government documents, drawings, and publications form a part of this specification to the extent specified herein. Unless otherwise specified, the issues sha

13、ll be those in effect on the date of the solicitation. LAWS AND REGULATIONS * US POSTAL SERVICE MANUAL 3 RULES AND REGULATIONS UNDER THE WOOL PRODUCTS LABELING ACT OF 1939 L . (Applications for copies should be addressed to the Superintendent of Documents, US Government Printing Office, Washington,

14、DC 20402-0001,) US DEPARTMENT OF AGRICULTURE Methods of Test for Grades of Wool Top (Applications for copies should be addressed to the US Department of Agriculture, Agricultural Marketing Service, Washington, DC 20580-0001.) RULES AND REGULATIONS UNDER THE TEXTILE FIBER PRODUCTS LABELING ACT (Appli

15、cations for copies should be addressed to the Federal Trade Commission, Washington, DC 20250-0001.) * 2.2 Other publications. The following document(s) form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of documents which are DoD adopted shall be

16、 those listed-in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the nongovernment documents which is current on the date of the solicitation. NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., A

17、GENT National Motor Freight Classification (Applications for copies should be addressed to the American Trucking Association, ATTN:. Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404.) UNIFORM CLASSIFICATION COMMITTEE, AGENT Uniform Freight Classification (Applications for copies sh

18、ould be addressed to the Uniform Classification Committee, Room 1106, 222 South Riverside Plaza, Chicago, Illinois 60606-5808.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-I_ - -_ -_ - MIL-C-3735E 3 777790b 0374266 5 W MIL-C-3735E TECHNICAL MAN

19、UAL OF THE AMERICAN ASSOCIATION OF TEXTILE CHEMISTS AND COLORISTS (AATCC) Chromatic Transference Scale Method No. 8 Colorfastness to Crocking: AATCC Crocheter Method (Applications for copies should be addressed to the AATCC National Headquarters, P.O. Box 12215, Research Triangle Park, NC 27709-2215

20、.) * 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein, the text of this specification shall take precedence. Nothing in this specification, however, f. shall supersede applicable laws and regulations unless a specific exemptio

21、n has been obtained. 3, REQUIREMENTS I 3.1 Standard sample. When a standard sample is available, the finished types I, III and IV knitted cuffs and cloth shall be equal to or better than the standard sample with respect to all. the characteristics for which the standard sample is referenced. 3.2 Fir

22、st article. When specified, the contractor shall furnish samples for first article inspection and approval (see 4.3 and 6.2). 3.3 Materials. 3.3.1 Wool. The wool used in the fabrication of the type I cuffs and cloth shall be fleece or pulled sheeps wool or any combination thereof, not lower in grade

23、 than 56s US Standard (see 4.4.1). The use of reprocessed, reused or waste wool is prohibited. 3.3.1.1 Yarn. The yarn shall be 2-ply, spun from combed top (see 4.4.1). 3.3.2 Polyester. The polyester used in the fabrication of the type III cuffs shall be semi-dull, continuous filament and texturized,

24、 made from glycol terephthalate (see 4.4.1). 3.3.3 Aramid. The aramid used in the fabrication of the type IV cuffs and cloth shannform to the requirements specified in 3.3.3.1 through 3.3.3.2.2 when tested as specified in 4.4.1 (see 6.4). 3.3.3.1 Fiber. The fiber shall be aramid, 1.5 or 2.0 denier p

25、er filament, cut to a staple length of 1 1/2 to 2 inches. The fiber shall not carbonize (turn black or become a soft friable char) at a temperature below 675F. 3.3.3.2 Yarns. The knitting aramid yarn and the yarn for double covering of the spandex core shall conform to the requirements specified in

26、3.3.3.2.1 and 3.3.3.2.2. The aramid yarn shall be autoclaved prior to knitting and covering. The fiber specified in 3.3.3.1 shall be spun and 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3735E 83 977970b 0374267 7 M - MIL-C-3735E 3.3.3.2.2

27、 Elastic yarn. The elastic yarn shall double-covere (inner and outer cover). The core nominal count of 50/1 (cotton count) aramid yarn. * 3.;6 Color. The color of the finished types I, shall be as specified by the procuring activity be a yarn III (see 140 denier spandex core shall be covered with a

28、and IV cuffs and cloth 6.2). The color of the type I, class 4 cloth shall be Camouflage Green 483 (see 6.6). 3.4.1 - Wool. The color of the dyed type I cuffs and cloth shall be obtained by either top, yarn or piece dying, using suitable dyestuffs of required fastness properties to meet the requireme

29、nts specified in 3.4.5 and spectral reflectance requirements for type I class 4 cloth as specified in 3.4.1.2. 3.4.1.1 Mothproofing. In the dyeing operation the top, yarn or fabric shall be mothproofed in accordance with MIL-C-43665. * 3.4.1.2 Spectral reflectance. The dyed and finished type I, clas

30、s 4 cloth shall conform to the reflectance values specified below when tested as specified in 4.5. Spectral reflectance requirements for type I class 4 cloth Type 1 Wavelength Reflectance (%) Nanometers (nm) Max. Min. 640 660 680 700 7 20 740 7 60 780 800 820 840 10 4 10 4 11 13 15 20 30 40 49 55 60

31、 64 67 4 4 4 6 9 14 19 24 29 34 39 3.4.2 Pol ester. The color of the dyed type III cuffs shall be obtained with suita + e dyestuffs of required fastness properties to meet the requirements specified in 3.4.5. * 3.4.3 Aramid. The color of the dyed type IV cuffs and cloth shall be obtained by the use

32、of a blend of producer-colored fibers using suitable dyestuffs of required fastness properties to meet the requirements specified e in 3.4.5. standard sample when artificial daylight, K, with illumination 3.4.4 Matching. The color and appearance of the dyed and finished types I, III and IV cuffs and

33、 cloth shall match the available viewed under filtered tungsten lamps that atproximatoe having a correlated color temperature of 7590 (+ - 200 ) 5 - 7- Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-C-3735E of 100 (+ 20) foot candles and shatl b

34、e a good match to the standard sample under infindescent lamplight at 2300 (+ - 200) K. 3.4.5 Colorfastness. * 3i4.5.1 Types I and III cuffs and cloth. The dyed and finished types I and III cuffs and cloth shall show colorfastness to light, laundering, perspiration, wet-dry cleaning and crocking equ

35、al to or better than the standard sample when tested as specified in 4.5. As a limit of acceptability or when no standard sample is available, the dyed and finished types I and III cuffs and cloth shall show a minimum of “good“ fastness to light, laundering, perspiration, wet-dry cleaning and shall

36、have an AATCC Chromatic Transference Scale rating for crocking of not lower than 3.5, when tested as specified in 4.5. * 3.4.5.2 Type IV cuffs and cloth. The dyed and finished type IV cuffs and cloth shall show colorfastness to light and laundering (after 3 cycles) equal to or better than the standa

37、rd sample when tested as specified in 4.5. As a limit of acceptability or when no standard sample is available, the dyed and finished type IV cuffs and cloth shall show a minimum of I1fair1 fastness to light and rtgoodlt fastness to laundering (after 3 cycles) when tested as specified in 4.5. 3.5 Sh

38、rink resistant treatment. When specified (see 6.2), the wool used for the type I cuffs and cloth shall be treated for resistance to felting shrinkage in top, yarn or fabric form by a chlorination method approved by the procuring activity. 3.5.1 Alkali solubility. When specified (see 6.2) the alkali

39、solubility of the shrink resistant wool for the finished type I cuffs and cloth in the form in which it has been treated (top, yarn or fabric) shall not be increased by more than 6.0 percent (absolute) over the untreated material when tested as specified in 4.4.1 or 4.5. 3.6 Construction. 3.6.1 Type

40、 I, class 1 ankle cuffs. The wool ankle cuffs, conforming to the physical requirements specified in Table 1 when tested as specified in 4.5, shall be constructed seamless in one size on a circular knitting machine using a 1 x 1 rib stitch with one end of yarn per feed (see 3.3.1.1). The ends of the

41、cuffs shall be tapered with a tuck or expanding stitch (see A, Figure 1). 3.6.2 Type I, class 2 wrist cuffs. The wool wrist cuffs, conforming to the physical requirements specified in Table I when tested as specified in 4.5, shall be constructed seamless in two sizes on a circular knitting machine u

42、sing a 1 x 1 rib stitch with one end of yarn per feed (see 3.3.1.1). The ends of the cuffs shall be tapered with a tuck or expanding stitch (see A, Figure 1) * 3.6.3 Type I, classes 3 and 4 knitted cloth. The knitted cloth for ankle and wrist cuffs, waistbands and collars, conforming to the physical

43、 requirements specified in Table I when tested as specified in 4.5, shall be constructed on a circular or flat knitting machine using a 1 x 1 rib stitch with one end of yarn per feed (see 3.3.l.1 and 6.9). Class 4 cloth shall be 6 Provided by IHSNot for ResaleNo reproduction or networking permitted

44、without license from IHS-,-,-MIL-C-3735E 3 9999906 037Li2b9 O W - MIL-C-3735E a knitted utilizing 0.35 to 0.40 inches of yarn per rib. 3.6.4 Type III, class 2 wrist cuffs. The polyester wrist cuffs, confarming to the physical requirements specified in Table I when tested as specified in 4.5,- shall

45、be constructed seamless in one size on a circular knitting machine using a 1 x 1 rib stitch with yarn as specified in 3.3.2 (see 6.5). The ends of the cuffs shall be tapered with a tuck or expanding stitch (see A, Figure 1) 3.6.5 Type IV, class 2 wrist cuffs. The aramid wrist cuffs, conforming to th

46、e physical requirements specified in Table I when tested as specified in 4.5,-shall be Constructed seamless in one size on a circular knitting machine using a 1 x 1 rib stitch with one end of the elastic yarn specified in 3.3.3.2.2 laid in every sixth course in the rib knit area (see B, Figure 1). T

47、he ends of the cuffs shall be tapered with a tuck or expanding stitch, with one end of the above specified elastic yarn laid in every third course (see A, Figure 1). * 3.6.6 Type IV, class 1 ankle cuffs. The aramid ankle cuffs, conforming to the physical requirements specified in Table I when tested

48、 as specified in 4.5, shall be constructed seamless in one size on a circular knitting machine using a 1 x 1 rib stitch with one end of the elastic yarn specified in 3.3.3.2.2 laid in every sixth course in the rib knit area (see B, Figure 1). The ends of the cuffs shall be tapered with a tuck or exp

49、anding stitch, with one end of the above specified elastic yarn laid in every third course (see A, Figure 1). * 3.6.7 Type IV, class 3 knitted cloth. The aramid knitted cloth for ankle cuffs and waistbands, conforming to the physical requirements specified in Table I when tested as specified in 4.5, shall be constructed on a circular or flat knitting machine using a 1 x 1 rib stitch with one end of the el