NAVY MIL-B-21117 E-1990 BADGE RATING AND QUALIFICATION DUNGAREE UNIFORM《级别和资格徽章 粗布制服》.pdf

《NAVY MIL-B-21117 E-1990 BADGE RATING AND QUALIFICATION DUNGAREE UNIFORM《级别和资格徽章 粗布制服》.pdf》由会员分享，可在线阅读，更多相关《NAVY MIL-B-21117 E-1990 BADGE RATING AND QUALIFICATION DUNGAREE UNIFORM《级别和资格徽章 粗布制服》.pdf（13页珍藏版）》请在麦多课文档分享上搜索。

1、MIL-B-21117D(NU) 21 February 1985 MILITARY SPECIFICATION BADGE, RATING AND QUALIFICATION, DUNGAREE UNIFORM This specification is approved for use by the Navy Clothing and Textile Research Facility, Department of the Navy, and is available for use by all Departments and Agencies of the Department of

2、Defense. 1. SCOPE 1.1 Scope. This specification covers the requirements for an iron-on rating and qualification badge for dungaree uniforms. 2. APPLICABLE DOCUMENTS 2.1 Government documents. 2.1.1 Specifications, standards, and handbooks. The following specifications, standards and handbooks form a

3、part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). Beneficial comme

4、nts (recommendations, additions, deletions) and any pertinent data which may be of use in improving this document should be addressed to: Officer in Charge, Navy Clothing and Textile Research Facility, P.O. Box 59, Natick, MA 01760-0001 by using the self-addressed Standardization Document Improvemen

5、t Proposal (DD Form 1426) appearing at the end of this document or bv letter. AMSC N/A FSC 8455 DISTRIBUTION STATEMENT A. Approved for public release; distribution is unlimited. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-ZLLIJE 4 777770b 0

6、450187 b SPECIFICATIONS MILITARY * MIL-P-15011 - Pallet, Material Handling, Wood, Post Construction, , 4 Way Entry MIL-B-17757 - Box, Shipping, Fiberboard (Modular Sizes) MIL-C-87065 - Cloth, Chambray, Polyester and Cotton STANDARDS FEDERAL FED-STD-191 - Textile Test Methods MILITARY MIL-STD-105 - S

7、ampling Procedures and Tables for Inspection by MIL-STD-129 MIL-STD-147 - Palletized Unit Loads Attributes - Marking for Shipment and Storage * MIL-STD-2073-1 - DOD Materials Procedures for Development and * MIL-STD-2073-2 - Packaging Requirement Codes Application of Packaging Requirements * (Unless

8、 otherwise indicated, copies of federal and military specification, standards, and handbooks are available from the Standardization Documents Order Desk, Building 4D, 700 Robbins Avenue, Philadelphia, PA 19111-5094.) 2.1.2 Other Government documents, drawings, and publications. The following other G

9、overnment documents, drawings, and publications form a part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the solicitation. U.S. POSTAL MANUAL (Copies of the manual may be obtained from the Superintendent of Documents, U.S. Government Prin

10、ting Office, Washington, DC 20402-0001.) 2.2 Non-Government publications. The following documents form a part of this specification to the extent specified herein. Unless otherwise specified, the issue of documents which are DoD adopted shall be those listed in the issue of the DODISS cited in the s

11、olicitation. Unless otherwise specified, the issues of documents not listed in the DODISS are the issues of the documents cited in the solicitation (see 6.2). NATIONAL MOTOR FREIGHT TRAFFIC ASSOCIATION, INC., AGENT National Motor Freight Classification (Applications for copies should be addressed to

12、 the American Trucking Association, ATTN: Traffic Department, 1616 P Street, N.W., Washington, DC 20036-1404.) 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-. _ ._ MIL-B-ZLLL?E 84 1p939390b Oy50JB8 8 H- MIL-B-21117E(NU) UNIFORM CLASSIFICATION COM

13、MITTEE, AGENT I Uniform Freight Classification (Amdication for coDies should be addressed to the Uniform Classification O Committee, Room 1106, 222 South Riverside Plaza, Chicago, IL 60606-5808. ) * (Non-Government standards and other publications are normally available from the organizations that p

14、repare or distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this document and the references cited herein, the text of this document takes precedence. Nothi

15、ng in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Guide sample. Samples, when furnished, are solely for guidance and information to the contractor (see 6.3). Variations from this specification may appear in the

16、 sample in which case this specification shall govern. 3.2 First article. When specified, the contractor shall furnish sample unit(s) for first article inspection and approval (see 4.3 and 6.2). 3.3 Material. 3.3.1 Basic material. The basic material shall be a polyester/cotton chambray cloth conform

17、ing to MIL-C-87065, except the seam efficiency requirements specified therein shall not apply. 3.3.2 Coating compound. The coating compound used to adhere the badge shall be a clear thermoplastic resin suitably compounded to meet the requirements specified herein. The resin shall be bacteria and fun

18、gi resistant, non-toxic, non-irritant, and free of any impurity that might cause fabric deterioration or discoloration on the printed side of the finished badge (see 4.4.1). badge shall be of a suitable black shade to match the guide sample. 3.3.3 Printing ink. The ink for printing the insignia on f

19、ace side of 3.3.3.1 Colorfastness. The printed matter on the finished badge shall show a minimum of llgoodl fastness to light, hot-dry pressing, chlorine bleaching and laundering when tested as specified in 4.5. 3.4 Coated fabric. The basic chambray material shall be evenly coated on one side only w

20、ith the resin compound specified in 3.3.2, to finish with the coating heat sealable with good adhesion characteristics. The coated side shall not show any evidence of blocking when tested as specified in 4.4.1. An acceptable degree of adhesion on the coated side of the finished badge shall be determ

21、ined as follows: - No clear evidence of curling or peeling will result when the badge is subjected to mobile launderings and accelerated aging as specified in 4.5. 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-21117E 84 7777706 0450389 T -

22、I a 3.5 Figures. Figures are furnished for information purposes only. When inconsistancies exist between the wrivten specification and the figures, the written specification shall govern. 3.6 Workmanship. The finished badges shall conform to the quality established by this specification. The occurra

23、nce of defects shall not exceed the applicable acceptable quality levels. 3.7 Tolerances. The tolerances shown in Table I shall apply for the dimensions as indicated. All measurements are in inches (see 4.4.2.2 and figures) . Table I - Tolerances Dimens ion Tolerance Any specified dimension under 15

24、/16 Any specified dimension of 1 and up to 1-15/16 Any specified dimension of 2 and up to 2-15/16 Any specified dimension of 3 and up to 3-15/16 Any specified dimension of 4 and up to 4-15/16 Any specified dimension of 5 and up to 5-15/16 Any specified dimension of 6 and up to 6-15/16 Any specified

25、dimension of 7 and up to 7-15/16 + 1/32 - + 1/16 - + 3/32 + 1/8 + 5/32 - 3/16 - + 7/32 + 1/4 - - - 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order; the contractor is responsible for the performance of all inspection requ

26、irements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other facilities suitable for performance of the inspection requirements specified herein, unless disapproved by the Government. The Governmen

27、t reserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements. * 4.1.1 Responsibility for compliance. All items must meet all requirements of sections 3 and 5. The i

28、nspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of ensuring that all products or supplies submitted to

29、 the Government for acceptance comply with all requirements of the contract. Sampling inspection, as part of manufacturing operations, is acceptable practice to ascertain conformance to requirements, however, this does not authorize submission of known defective material, either indicated or actual,

30、 nor does it commit the government to acceptance of defective material. 4.1.2 Certificate of compliance. Where certificates of compliance are submitted, the Government reserves the right to check test such items to determine the validity of the certification. 4 Provided by IHSNot for ResaleNo reprod

31、uction or networking permitted without license from IHS-,-,-4.2 Classification of inspection. The inspection requirements specified herein are classified as follows: 1. 2. First article inspection (see 4.3). Quality conformance inspection (see 4.4). 4.3 First article inspection. When required, the f

32、irst article submitted in accordance with 3.2, shall be inspected as specified in 4.4.2 for compliance with design, construction, workmanship, appearance and dimensional requirements. 4.4 Quality conformance inspection. Sampling for inspection shall be performed in accordance with MIL-STD-105, excep

33、t where otherwise indicated. 4.4.1 Component and material inspection. In accordance with 4.1 above, components and materials shall be tested in accordance with all the requirements of referenced specifications, drawings, and standards unless otherwise excluded, amended, modified, or qualified in thi

34、s specification or applicable procurement documents. In addition, components and materials listed in Table II shall be tested for the characteristics specified and in accordance with FED-STD-191 whenever applicable. All test reports shall contain individual values utilized in expressing the final re

35、sult. The lot size for the coated fabric shall be expressed in yards and the sample unit shall be 1/2 yard (full width). The sample size shall be as follows: Lot size (yards) 800 or less 801 up to and including 22,000 22,001 and over Sample size 2 3 5 The lot shall be unacceptable if one or more uni

36、ts fail to meet any requirement specified. Table II - Component testing Requirement Test Component Characteristic paragraph met hod Coating compound Resistance to Bacteria and Fungi 3.3.2 1/ Material Identification 3.3.2 i/ Toxicity 3.3.2 i/ Cloth, coated Coating, heat sealable 3.4 i/ Blocking 3.4 5

37、872 - 1/ A certificate of compliance shall be submitted and will be acceptable for the stated requirement. contractor must confirm that irritants or chemicals that could cause dermatitis problems or deterioration of the basic fabric while in storage are not present. In respect to the toxicity of the

38、 coating, the 5 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-4.4.2 Examination of the end item. The defects found during the examination of the end item shall be classified in accordance with 4.4.2.1 and 4.4.2.2. The applicable inspection levels a

39、nd acceptable quality levels (AQLs) shall be as indicated in 4.4.2.3. The lot size shall be expressed in units of one badge. The sample unit shall be one finished badge. 4.4.2.1 Visual examination. Examine Defect Design Any deviation from illustration or guide sample. Color of printing not as specif

40、ied. Design poorly defined, distorted, or misshaped. Not properly positioned or centered. Any woven or finishing defect seriously affecting the Any hole, cut, or tear. Any uncoated area clearly visible on back side of badge. Coating omitted. Spot, stain, or imbedded foreign matter clearly noticeable

41、 Print not distinct or blurred Overall discoloration clearly noticeable on face side of Mat erial overall appearance of the badge. on face side of badge. badge. Workmanship 4.4.2.2 Dimensional examination. The finished badge shall be examined for dimensional defects in accordance with the applicable

42、 figure. Any measurement deviating from the dimension specified shall be scored as a size measurement defect (see Table I for tolerance). 4.4.2.3 Inspection levels and acceptable quality levels (AQLs). The inspection levels and the acceptable quality levels, expressed in defects per 100 units for vi

43、sual and dimensional examination, shall be as follows: Inspection level - AQL For defects applicable to 4.4.2.1 For defects applicable to 4.4.2.2 II 4.0 s-3 6.5 4.4.3 Examination of packaging requirements. An examination shall be made to determine that packaging, packing, and marking comply with Sec

44、tion 5 requirements of this specification. Defects shall be scored in accordance with the list below. The sample unit shall be one shipping container fully prepared for delivery. Defects of closure listed below shall be examined on shipping containers fully prepared for delivery. The lot size shall

45、be on the number of shipping containers in the end item inspection lot. The inspection level shall be S-2 and the acceptable quality level (AQL) shall be 2.5, expressed in terms of defects per hundred units. 6 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from

46、IHS-,-,-Examine Defect Marking (exterior Omitted, incorrect, illegible, of improper size, and interior) location, sequence, or method of application. Materials Any component missing, damaged, or not as specified. Workmanship Content Inadequate application of components, such as: incomplete closure f

47、 container flaps , loose strapping, improper taping, inadequate stapling, bulged or distorted container. Number of items per shipping container is more or Size shown on one or more items not as specified on less than required. shipping container. - 1/ - 1/ For this defect, one item from each shippin

48、g container in sample shall be examined. 4.4.4 Palletization examination. An examination shall be made to determine that the palletization complies with the section 5 requirements. Defects shall be scored in accordance with the list below. The sample unit shall be one palletized unit load fully pack

49、aged. The lot size shall be the number of palletized unit loads in the end item inspection lot. The inspection level shall be S-1 and the AQL, expressed in terms of defects per hundred units, shall be 6.5 as specified in MIL-STD-105. Examine 0 Defect Finished dimensions Length, width, or height exceeds specified maximum requirements. Palletization Pallet pattern not as specified. Interlocking of loads not as specified. Load not bonded with required str