NAVY DOD-R-23679 F-1986 REAGENTS STANDARD WATER TEST CHEMICALS (METRIC)《水化学物测试标准试剂(公制)》.pdf

《NAVY DOD-R-23679 F-1986 REAGENTS STANDARD WATER TEST CHEMICALS (METRIC)《水化学物测试标准试剂(公制)》.pdf》由会员分享，可在线阅读，更多相关《NAVY DOD-R-23679 F-1986 REAGENTS STANDARD WATER TEST CHEMICALS (METRIC)《水化学物测试标准试剂(公制)》.pdf（11页珍藏版）》请在麦多课文档分享上搜索。

1、i?- 2 b-1) -1 DOD-R-23677F 68 m 7777706 OLL837L 5 m DOD-R-23 679F( SH) 8 August 1986 SUPERSEDING DOD-R-23679E(SH) 16 November 1981 (See 6.6) MILITARY SPECIFICATION REAGENTS, STANDARD, WATER TEST CHEMICALS (METRIC) This specification is approved for use within the Naval Sea Systems Command, Departmen

2、t of the Navy, and is available for use by all Departments and Agencies of the Department of Defense. 1. SCOPE 1.1 Scope. This specification covers reagents for use in checking the quality of water testing chemicals and equipments used in boiler powered ships. 1.2 Classification. Standard reagents s

3、hall be of the foliowing classes, as specified (see 6.3). Class e - Standard hardness solution, 0.20 equivalent per million Class i - Standard conductivity solution, 1400 microsiemens per Class k - Standard chloride solution, 2.00 elm chloride. Class m - pH standard, buffer capsules pH - 10.00 - + 0

4、.05 at 25 Class n - pH standard, buffer capsules pH - 7.00 + 0.05 at 25OC. Class p - Standard-methyl purple alkalinity standard 6.0 e/m. (e/m hardness). centimeter (ps/cm). degrees Celsius (OC). Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in

5、 improving this document should be addressed to: Commander, Naval Sea Systems Command, SEA 5523, Department of the Navy, Washington, DC 20362-5101 by using the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearing at the end of this document or by letter. AMSC NIA FSC

6、 6810 DISTRIBUTION STATEMENT A Approved for public release; distribution unlimited -, / THIS DOCUMENT CONTAINS 11 PAGES. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,- - DD-R-23679F 68 9994906 L18372 7 W DOD-R-23679F( SEI) 2. APPLICABLE DOCUMENTS 2

7、.1 Government documents. 2.1.1 Specifications and standards. The following specifications and standards form a part of this specification to the extent specified herein, Unless otherwise specified, the issues of these documents shall be those listed in the issue of the Department of Defense Index of

8、 Specifications and Standards (DoDISS) and supplement thereto, cited in the solicitation. SPECIFICATIONS FEDERAL PPP-B-601 - Boxes, Wood, Cleated-Plywood. PPP-B-621 - Boxes, Wood, Nailed and Lock-Corner. PPP-B-636 - Boxes, Shipping, Fiberboard. PPP-C-186 - Containers, Packaging and Packing for Drugs

9、, Chem- icals, and Pharmaceuticals. MILITARY MIL-L-10547 - Liners, Case, and Sheet, Overwrap; Water-Vaporproof MIL-W-15000 - Water-Testing Chemicals, Boiler, Shipboard Use. or Waterproof, Flexible. STANDARDS FEDERAL FED-STD-313 - Material Safety Data Sheets Preparation and the Submission of . MILITA

10、RY MIL-STD-105 - Sampling Procedures and Tables for Inspection by MIL-STD-129 - Marking for Shipment and Storage. MIL-STD-414 - Sampling Procedures and Tables for Inspection by Variables for Percent Defective. Attributes. 2.1.2 Other Government documents. The following other Government docu- ments f

11、orm a part of this specification to the extent specified herein. Unless otherwise specified, the issues shall be those in effect on the date of the solicitation. DEPARTMENT OF LABOR (OSHA) Code of Federal Regulations (CFR) CFR 29, Part 1910.1200 - Bazard Communication Standard. DEPARTMENT OF TRANSPO

12、RTATION (DOT) Code of Federal Regulations (CFR) CFR 49, Parts 170-179 - Hazardous Material Regulations. 2 . Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DOD-R-23677F 68 m 7777906 0338373 7 m DOD-R-2 3 6 7 9 F ( SH) (The Code of Federal Regulations

13、 (CFR) and the Federal Register (FR) are for sale on a subscription basis by the Superintendent of Documents, U.S. Government Printing Office, Washington, DC 20402. When indicated, reprints of certain regulations may be obtained from the Federal agency responsible for issuance thereof.) (Copies of s

14、pecifications, standards, and other Government documents required by contractors in connection with specific acquisition functions should be obtained from the contracting activity or as directed by the contracting activity.) 2.2 Other publications. The following documents form a part of this specifi

15、cation to the extent specified herein. Inless otherwise specified, the issues of the documents which are DoD adopted shall be those listed in the issue of the DoDISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DoDISS shall be the issue of the

16、nongovernment documents which is current on the date of the solicitation. AMERICAN CHEMICAL SOCIETY (ACS) Specifications - Reagent Chemicals. (Application for copies should be addressed to Applied Publications, American Chemical Society, 1155 16th Street, NW, Washington, DC 20036.) AMERICAN SOCIETY

17、FOR TESTING AND MATERIALS (ASTM) (DoD adopted) Resistivity of Water. (DoD adopted) D 512 - Standard Test Methods for Chloride Ion in Water. D 1125 - Standard Test Methods for Electrical Conductivity and D 1126 - Standard Test Method for Hardness in Water. D 1193 - Standard Specification for Reagent

18、Water. D 1293 - Standard Test Methods for pH of Water. (DoD adopted) (DoD adopted) (Application for copies should be addressed to the American Society for Testing and Materials, 1916 Race Street, Philadelphia, PA 19103.) (Nongovernment standards and other publications are normally available from the

19、 organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this specification and the references cited herein (except for assoc

20、iated detail specifications, specification sheets or MS standards), the text of this specifi- cation shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unless a specific exemption has been obtained. 3 . REQUIREMENTS 3.1 Standard reagents. A

21、il reagents shall conform to specifications of the ACS. to the Government laboratory with samples or quality conformance testing as specified in 4.2.3. Manufacturer and lot number for ACS grade reagents shall be provided 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without

22、license from IHS-,-,- DOD-R-23b7?Fpb 77777Ob OLL8374 0 DOD-R-23679F(SH) 3,l.l Class e - standard hardness solution, 0.20 e/m hardness. 3*1.1.1 Composition. Standard hardness solution shall contain 0.0111 a grame of reagent grade anhydrous calcium chloride per liter (L) of type II reagent grade water

23、 solution. hardness in milliequivalents per liter (meq/L) shall be 0.20 - + 0.03 meq/L. When tested in accordance with 4.4.1, the total 4 3.1.2 C1ass.i - standard conductivity solution, 1400 ps/cm. v 3.1.2.1 Composition. Standard conductivity solution shall contain 0.7440 * grams of reagent grade an

24、hydrous potassium chloride per L of type II reagent grade water solution. When tested in accordance with 4.4.2, the Conductivity value of the solution shall be 1400 2 25 ps/cm. “ 3.1.3 Class k - standard chloride solution, 2.00 e/m chloride. 3.1.3.1 Composition. Standard chloride solution shall cont

25、ain 0.1170 grams of reagent grade anhydrous sodium chloride per L of type II reagent grade water solution. When tested in accordance with 4.4.3, the chloride ion concen- tration in milligrams per L (mg/L) shall be 70.91 - + 1.40 mg/L. 3.1.4 Class m - pH standard, pH - 10.00 + 0.05 at 25OC. 3.1.4.1 T

26、he pH standard shall be a stable buffer powder in capsule form. When the contents of one capsule are dissolved in 100 milliliters (mL) of type PI reagent grade water at 25“C, the resultant solution shall be free of turbidity or undZssolSed particles. shall yield a pH of 10.00 - + 0.05. When tested i

27、n accordance with 4.4 .i, this solution 3.1.5 3.1.5.1 Class n - pH standard, pH 7.00 + 0.05 at 25OC. The pH standard shall be a stable buffer powder in capsule form. Nien the contents of one capsule are dissolved in 100 mL of type II reagent grade water at 25OC, the resultant solution shall be free

28、of turbidity or undissolved particles. When tested in accordance with 4.4.5, this solution shall yield a pH O 7.00 2 0.05. 3.1.6 Class p - standard methyl purple alkalinity (6.0 e/m). 3.1.6.1 Composition. The standard shall consist of 0.318 grams of ACS reagent grade sodium carbonate per L of distil

29、led or demineralized water solution. The eodium carbonate shall conform to the Specifications for Reagent Chemicals of the ACS. The sodium carbonate shall be dried in an oven at 25OoC for 4 hours then cooled in a desiccator prior to preparing the standard. 4.4.6, the alkalinity in e/m should not be

30、more than 6.2 nor less than 5.8. The water shall be in accordance with ASTM D 1193, type III. When tested in accordance with 3.2 Material safety data sheet. The contracting activity shall be pro- vided a material safety data sheet (MSDS) at the time of contract award. The MSDS shall. be provided in

31、accordance with the requirements of FED-STD-313 and 29 CFR 1910.1200, Hazard Communication, When FED-STD-313 is at variance with the CFR, 29 CFR 1910.1200 shall take precedence, modify and supplement PED-STD-313. covered by this specification. The MSDS shall be included with each shipment of the mat

32、erial 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-DOD-R-23679F 68.- 9977706 0338375 2 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for inspection. Unless otherwise specified in the contract or purchase order, the contractor is responsible

33、 for the performance of all inspection requirements as specified herein. fied in the contract or purchase order, the contractor may use his own or any other facilities suitable for the performance of the inspection requirements specified herein, unless disapproved by the Government. The Government r

34、eserves the right to perform any of the inspections set forth in the specification where such inspections are deemed necessary to assure supplies and services conform to prescribed requirements. Except as otherwise speci- 4.1.1 Responsibility for compliance. All items must meet all requirements of s

35、ections 3 and 5. The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall not relieve the contractor of the responsibility of assuring that all products or

36、 supplies submitted to the Government for acceptance comply with all requirements of the contract. Sampling in quality conformance does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to acceptance of defective material. 4.1.2 Inspe

37、ction system. The contractor shall provide and maintain an inspection system in accordance with the data ordering documents included in the contract or order (see 6.2.2). 4.2 Quality conformance inspection. 4.2.1 - Lot. For purposes of sampling, a lot shall consist of all solutions or chemicals from

38、 one batch of a single class. 4.2.2 Sampling for examination of filled containers. A random sample of filled containers shall be selected from each lot in accordance with MIL-STD-105 at inspection level I, and acceptable quality level (AQL) of 2.5 percent defec- tive to verify compliance with all re

39、quirements of this specification regarding fill, closure, marking, and other requirements not involving tests. 4.2.3 Sampling for quality conformance tests. Unless a different labora- tory is specified (see 6.2.1), 60 bottles shall be selected from each lot of material and forwarded to the David W.

40、Taylor Naval Ship Research and Develop- ment Center, Annapolis Laboratory, Annapolis, MD 21402 for the tests specified in 4.4 and 4.5. A copy of the test and evaluation report for each lot, noting contract number, national stock number, lot/batch number and date of manufacture, shall be included, as

41、 specified (see 6.2.2). 4.2.3.1 Classes e, i, k, and p. The results of the tests shall be employed to estimate the percent nonconforming in the lot by computations in accordance with MIL-STD-414, example B-3. fication limits shall be 4.0 percent for both limits combined. The maximum allowable percen

42、t outside the speci- 4.2.3.2 Classes m and n. One capsule from each bottle shall be dissolved If any in 100 mL of distilled water and t-ested as specified in 4.4.4 or 4.4.5. buffer fails this test, this shall be cause for rejection of the lot. 5 f Provided by IHSNot for ResaleNo reproduction or netw

43、orking permitted without license from IHS-,-,-4.2.3.3 If the computations as specified in 4.2.3.1 show that more than 4.0 percent of the lot is outside the specification limits for any class, this shall be cause for rejection of the entire lot. 4.2.3.4 Delivery of the material shall be withheld pend

44、ing notification of the results of tests. 4.3 Examinations. B 4.3.1 Examination of filled containers. Each sample filled container selected in accordance with 4.2.2 shall be examined for defects of the container * and the closure, for evidence of leakage, and for unsatisfactory markings. Any - conta

45、iner in the sample, having one or more defects, or under required fill, shall be cause for rejection, and if the number of defective containers in any sample exceeds the acceptance number for the appropriate sampling plan in accor- dance with MIL-STD-105, this shall be cause for rejection of the lot

46、 represented by the sample. 4.4 Tests. 4.2.3 shall be subjected to the applicable tests specified herein. All tests shall be conducted at room temperature. Each of the samples selected and forwarded in accordance with 4.4.1 Class e - standard hardness solution, 0.20 e/m hardness (see 4.4.7). Measure

47、 the total hardness concentration in accordance with ASTM D 1126, 9.2. low hardness method. Record value. The calcium solution standard used for-stand- crrdizing the disodium ethylenediamine tetraacetate solution shall be prepared using Standard Reference Material calcium carbonate from the National

48、 Bureau of Standards. 4.4.2 Class i - standard conductivity solution, 1400 ps/cm (see 4.4.7). Determine the cell constant of the conductivity cell which will be used for test- ing the standard conductivity solution in accordance with ASTM D 1125, method A. The potassium chloride reference solution s

49、hall be prepared using Standard Reference Material potassium chloride from the National Bureau of Standards. I-leasure electrical conductivity of the standard conductivity solution in accor- dance with ASTMD 1125, method A. Record value. 4.4.3 Class k - standard chloride solution, 2.00 e/m chloride (see 4.4.7). Measure the chloride ion concentration in accordance with ASTM D 512, method A (mercurimetric, titration). Record value. The sodium chloride reference solu- tion us