NAVISTAR TMS 9546-2007 Quality Requirements for Two-Piece Wheel Nuts (Revision C).pdf

《NAVISTAR TMS 9546-2007 Quality Requirements for Two-Piece Wheel Nuts (Revision C).pdf》由会员分享，可在线阅读，更多相关《NAVISTAR TMS 9546-2007 Quality Requirements for Two-Piece Wheel Nuts (Revision C).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、INTERNATIONAL TRUCK AND ENGINE CORPORATION TMS (TRUCK MATERIAL SPECIFICATION) NUMBER: TMS-9546 TITLE: Quality Requirements For Two-Piece Wheel Nuts REVISION: C WRITTEN/EDITED BY: Materials Engineering APPROVED BY: Materials Engineering DATE ISSUED: June 2007 PRINTED COPIES OF THIS DOCUMENT MUST BE V

2、ERIFIED FOR CURRENT REVISION This specification may involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the

3、 applicability of regulatory limits prior to use. Change Notice: Added corrosion test sampling requirements in Section 4.1. Reference: Keywords: Quality; Two-Piece Wheel Nuts 1.0 APPLICATION This specification covers International Engineering quality requirements for two-piece wheel nuts used in Int

4、ernational assembly plants to attach truck wheels to hubs. 2.0 SCOPEThis specification covers the corrosion and torque-tension, testing requirements, the quality plan, quality control, source approval, and shipping and identification requirements. 2.1 Restricted Chemical SubstancesEffective January

5、1, 2007, all product supplied to the requirements of this specification must comply with the requirements of the CEMS B-50 specification. 3.0 REFERENCE DOCUMENTS Unless otherwise specified the latest issue of all referenced standards shall apply. The following Specifications, Standards, and Regulati

6、ons are referenced in this specification. Quality System Standard ISO 9001 or TS-16949 CFR Title 40, Part 280 ASTM B 117 INTERNATIONAL Engr. Design Standard A-16 CFR Title 29, Part 1910 SAE J995 INTERNATIONAL Manufacturing Std D-13 ASME B1.1 SAE J1965 INTERNATIONAL CEMS B-50 ASME B1.13M 4.0 GENERAL

7、REQUIREMENTS Parts supplied shall meet all applicable requirements of CFR Title 40, Part 280. Testing requirements and a sampling plan consistent with those described in SAE J995 shall be used. 4.1 Corrosion Test Requirements Corrosion testing per ASTM B 117 shall be performed at the supplier locati

8、on from which finished parts are shipped to the International assembly plants, or corrosion testing shall be performed on test samples taken from that location. Each test lot will consist of a minimum of five samples. This document is restricted and may not be sent outside International Truck and En

9、gine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. JUNE 2007 Page 1 of 3 NUMBER: TITLE: REVISION: TMS-9546 Quality Requirements For Two Piece Wheel Nuts C Thi

10、s document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. 4.1.1 Acceptance Criteria Af

11、ter salt spray testing for minimum 240 hrs, there shall be no more than one rust spot, provided that such spot is not larger than 1/16 inch diameter on the significant surfaces* of the nut, and no more than 2% total rust on all surfaces of the nut. All five test samples must pass the salt spray test

12、ing requirements in order to be considered acceptable. (*Significant surfaces are those normally visible when the nut is installed in the final assembly position and includes the interior and bottom of the flange surface and excludes the hex corners, edges, lettered top, and thread form. ) 4.2 Torqu

13、e Tension Test Requirements Wheel nuts supplied shall meet all requirements of SAE J1965. 5.0 QUALITY Production parts shipped to International facilities shall be delivered in a clean condition ready for assembly. Thread form shall conform to Class 2B as per ASME B1.1 or Class 6H per ASME B1.13M. 5

14、.1 Qualification New part suppliers shall submit a report certifying compliance to all requirements of this specification. A sample lot of not less than 50 pieces shall be submitted to TDTC Fastener Engineering for testing and evaluation. No parts shall be shipped for production use prior to formal

15、approval by TDTC Fastener Engineering. 5.2 Quality Control Plan A Quality Control Plan for this product will be established by mutual agreement between International and the supplier. The following items, where applicable*, will be included in the control plan as dimensional features for management

16、by statistical process control.* KCC1. Corrosion Test Performance 2. Proof Load * Other characteristics for inclusion in the control plan may be specified on the engineering drawing and/or purchase order. * See International Engineering Design Standard A-16 6.0 SOURCE APPROVAL AND QUALITY CONTROL 6.

17、1 Supplier Requirements All suppliers to International Truck and Engine are required to be registered to ISO 9001 Quality System Requirements. International will also accept TS-16949 registration as long as the supplier can also fulfill all AIAG PPAP (Production Part Approval Process) documentation

18、and approval requirements. Suppliers must maintain their certification with an accredited registrar and must furnish copies of registration certificates to their International Corporate Buyer upon request. JUNE 2007 Page 2 of 3 NUMBER: TITLE: REVISION: TMS-9546 Quality Requirements For Two Piece Whe

19、el Nuts C This document is restricted and may not be sent outside International Truck and Engine Corporation or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2007 by International Truck and Engine Corporation. 6.2 Approval Pa

20、rts supplied against contracts or purchase orders citing this specification shall be equivalent in all respects to those samples which were approved by the purchaser. No changes in formulation or processing practices are permitted without approval. In the event that changes in material, properties,

21、processing practices, construction, color, or labeling of the product are required, the supplier shall notify Materials Engineering at TDTC and Purchasing and Supplier Development of the proposed change(s). Test data indicating conformance to all requirements of this specification, test samples, and

22、 new or amended or updated Material Safety Data Sheet(s) (MSDS), in accordance with CFR Title 29, Part 1910 shall be submitted with the request for change. 6.3 Process Control The supplier shall either perform and report results of tests on specific lots of parts produced using ISO 9001 or TS-16949

23、guidelines, or provide statistical evidence of the lot having been produced in a state of statistical control and with a process capable of providing all required properties. The part supplier and the plant metallurgist and/or the quality control manager of the using International plant may determin

24、e testing and reporting requirements on specific products. 7.0 SHIPPING, PACKING AND IDENTIFICATION Loading, packing, and identification shall conform to Manufacturing Standard D-13. 8.0 DESIGNATION ON DRAWINGS Drawings will reference TMS-9546 for quality requirements. The KCC symbol will refer to T

25、MS-9546. 9.0 TECHNICAL INFORMATION For further information related to the technical content of this specification, contact: Suppliers may obtain controlled copies of this specification by contacting: Materials Engineering and Technology Dept. Truck Development and Technology Center 2911 Meyer Road Fort Wayne, IN 46803 E-mail: MaterialsEngineeringNav-I Information Handling Service (IHS) 15 Inverness Way East Englewood CO 80112-5776 Phone: 1-800-854-7179 E-mail: AutomotiveIHS.com Website: http:/JUNE 2007 Page 3 of 3