NAVISTAR CEMS DT-14-2009 Surface Waviness Definition via ALSA Analyzer.pdf

《NAVISTAR CEMS DT-14-2009 Surface Waviness Definition via ALSA Analyzer.pdf》由会员分享，可在线阅读，更多相关《NAVISTAR CEMS DT-14-2009 Surface Waviness Definition via ALSA Analyzer.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent liability. 2009 by Navistar, Inc. APRIL 2009 Page 1 of 2 NAVISTAR, INC. CEMS (ENGINEERING MATERIAL SPECIFICATION) N

2、UMBER: CEMS DT-14 TITLE: Surface Waviness Definition via ALSA Analyzer CURRENT ISSUE DATE: April 2009 WRITTEN/EDITED BY: Materials EngineeringAPPROVED BY: Materials Engineering SUPERSEDES ISSUE OF: April 2001 PRINTED COPIES OF THIS DOCUMENT MUST BE VERIFIED FOR CURRENT REVISION This specification ma

3、y involve hazardous materials, equipment, and procedures. This specification does not purport to address all of the safety issues associated with its use. The user is responsible to consult appropriate safety and health practices and to determine the applicability of regulatory limits prior to use.

4、Change Notice: Replaced “International Truck and Engine Corporation” with “Navistar, Inc.” per corporate directive; changed name of analyzer from Loria to ALSA . 1.0 APPLICATION This specification covers a method for determining surface quality of SMC panels using an Advanced Laser Surface Analyzer

5、(ALSA) . * 2.0 SCOPE This test method describes the procedure used to quantitatively determine the surface waviness of SMC substrates used for Class A exterior applications. The surface quality is evaluated in terms of an ALSA Index Value. 3.0 APPARATUS Required equipment is an Advanced Laser Surfac

6、e Analyzer (ALSA) , which is available from the Composite Polymer Division of Ashland Chemical Co.* This apparatus must be properly calibrated and standardized. 4.0 PROCEDURE In order to assure repeatability of the surface quality measurement or Index Value, it is essential that the test procedure b

7、e carefully controlled. The apparatus must be properly calibrated; the test specimen must be properly aligned between the laser and the reflective screen, and the laser incident angle carefully controlled. 4.1 Test Specimen The test specimen should be of sufficient size to allow a measured area of 2

8、50 x 250 mm (minimum) to be analyzed. The specimen surface must be sufficiently reflective to reflect the laser beam onto a screen, where it is recorded by a camera. A flat surface is preferred, but a curved surface may be used if it is free of styling lines, ribs, bosses or inflected spots in the a

9、rea to be measured. 4.2 Test Specimen Location The specimen or part to be analyzed should be placed approximately halfway between the laser and the screen, so that the first laser measurement line on the test specimen is 1550 mm in front of the reference mark on the laser apparatus. The reference li

10、ne on the front side of the laser should be 1070 mm above the measurement area on the test specimen. The reflective screen is mounted 3 meters in front of the reference mark on the laser apparatus . *ALSA is a registered trademark of Ashland Chemical Co., Composite Polymer Division, P.O. Box 2219, C

11、olumbus OH 43216 NUMBER: DT - 14 Title: Surface Waviness Definition via ALSA Analyzer CURRENT ISSUE DATE: April 2009 This document is restricted and may not be sent outside Navistar, Inc. or reproduced without permission from Corporate Technical Standards. Suppliers are required to assume all patent

12、 liability. 2009 by Navistar, Inc. APRIL 2009 Page 2 of 2 4.3 Test Procedure Allow the laser beam to move fully across the entire surface area of analysis and to be fully reflected on the screen and recorded by the camera. Make sure the laser beam can travel the length of the panel without moving of

13、f the panel surface. 4.3.1 ALSA Index Value Take readings on three specimens and average the result. The value of the individual readings shall not vary by more than 10 % from the average value. The average value of the three readings is the ALSA Index Value for that material and process. 5.0 REPORT Report the ALSA Index Value of the scanned samples. The Index Value should be submitted along with the material qualification data to Materials Engineering at Truck Development and Technology Center (TDTC).