ITU-T S 1-1993 International Telegraph Alphabet No 2 - Telegraphy - Alphabetical Telegraph Terminal Equipment (Study Group IX) 7 pp《国际电报字母表第2号-电报-按字母顺序排列的电报终端设备》.pdf

《ITU-T S 1-1993 International Telegraph Alphabet No 2 - Telegraphy - Alphabetical Telegraph Terminal Equipment (Study Group IX) 7 pp《国际电报字母表第2号-电报-按字母顺序排列的电报终端设备》.pdf》由会员分享，可在线阅读，更多相关《ITU-T S 1-1993 International Telegraph Alphabet No 2 - Telegraphy - Alphabetical Telegraph Terminal Equipment (Study Group IX) 7 pp《国际电报字母表第2号-电报-按字母顺序排列的电报终端设备》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、ITU-T RECMN*S.L 93 m 4862.593 0588726 bT4 m INTERNATIONAL TELECOMMUNICATION UNION ITU=T TELECOMMUNICATION STANDARDIZATION SECTOR OF ITU TELEGRAPHY ALPHABETICAL TELEGRAPH TERMINAL EQUIPMENT s.l (03193) INTERNATIONAL TELEGRAPH ALPHABET No. 2 ITU-T Recommendation S.l (Previously “CCIlT Recommendation”)

2、 ITU-T RECMN+S.L 73 W 48b257L 0588732 7T8 FOREWORD The ITU Telecommunication Standardization Sector (ITU-T) is a permanent organ of the International Telecom- munication Union. The ITU-T is responsible for studying technical, operating and tariff questions and issuing Recommendations on them with a

3、view to standardizing telecommunications on a worldwide basis. The World Telecommunication Standardization Conference (WTSC), which meets every four years, established the topics for study by the ITU-T Study Groups which, in their turn, produce Recommendations on these topics. ITU-T Recommendation S

4、.l was revised by the ITU-T Study Group IX (1988-1993) and was approved by the WTSC (Helsinki, March 1-12, 1993). NOTES 1 As a consequence of a reform process within the International Telecommunication Union (ITU), the CCIT ceased to exist as of 28 February 1993. In its place, the ITU Telecommunicat

5、ion Standardization Sector (ITU-T) was created as of 1 March 1993. Similarly, in this reform process, the CCIR and the IFRB have been replaced by the Radiocommunication Sector. In order not to delay publication of this Recommendation, no change has been made in the text to references containing the

6、acronyms “CCIIT, CCIR or IFFW or their associated entities such as Plenary Assembly, Secretariat, etc. Future editions of this Recommendation will contain the proper terminology related to the new ITU structure. 2 telecommunication administration and a recognized operating agency. In this Recommenda

7、tion, the expression “Administration” is used for conciseness to indicate both a O ITU 1994 All rights reserved. No part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from t

8、he ITU. ITU-T RECMN*S.L 93 48b259L 0588727 530 CONTENTS Page 1 Introduction 1 2 Character repertoire. . 1 5 3 Coding 2 4 Particular combinations 2 4.6 Use of capital and small letters . 3 4.7 Use of combination No. 32 . 4 Graphic representation of control characters 4 Recommendation S.l (03/93) i IT

9、U-T RECHN+S-L 93 W 4862593 0588728 477 Recommendation S.l INTERNATIONAL TELEGRAPH ALPHABET No. 2 (Malaga-Torremolinos, 1984; amended Melbourne, 1988 and Helsinki, 1993) 1 Introduction 1.1 This Recommendation defines the repertoire of the graphic and control characters used in International Telegraph

10、 Alphabet No. 2 (ITA2) and the coded representation of these characters for communication purposes. It also contains provisions concerning the use of certain specific combinations. 1.2 The coded character set of ITA2 is based on a 5-unit-structure. 1.3 ITA2 is also defined in Recommendation F. 1 for

11、 the international public telegram service, and it is specified in Recommendation F.60 that it should also be used for the telex service. It may also be used for other applications, such as specialized or leased circuits. 1.4 For definitions concerning alphabetic telegraphy, see definitions in Recom

12、mendation R. 140 and the International Electrotechnical Vocabulary (IEV), Chapter 721. 2 Character repertoire 2.1 Graphic characters that have a corresponding signal in ITA2 are: - - - the 26 latin alphabetic characters: A B C D E F G H I J K L M N O P Q R S T U V W X Y Z; decimal figures: O 1 2 3 4

13、 5 6 7 8 9; punctuation marks and miscellaneous signs: Full Stop Comma Colon or division sign Question mark ? Apostrophe 9 Cross or addition sign + Hyphen or dash or subtraction sign Fraction bar or division sign Equal sign or double hyphen Right-hand bracket (parenthesis) ) - I - - Left-hand bracke

14、t (parenthesis) 2.2 use (see 4.2). 2.3 graphic characters, nor does it define the layout of keyboards in teleprinters or similar terminal devices. Three graphic characters (such as accented letters and currency signs) may be applied for national or private This Recommendation does not define the par

15、ticular printing style, font or case (capital or small letters) of 2.4 The control characters provided in ITA2 are: - - - carriage return; - line-feed; “Who are you? (part of the signal to operate the answerback unit of the corresponding installation); operation of an audible signal of the correspon

16、ding installation; Recommendation S.1 (03/93) 1 ITU-T RECMNtS.1 93 48b259L 0588729 303 = - letter-shift; - figure-shift; - space or blank; - all-space or null (no tape perforation). 3 Coding 3.1 one of two significant conditions (A or Z), as shown in Table 1. The 32 combinations available in ITA2 ar

17、e produced by a sequence of five units, each of which may assume 3.2 Condition Z corresponds to stop polarity, perforation in paper tape and symbol 1 in the binary notation. Condition A corresponds to start polarity, no perforation in paper tape and symbol O of the binary notation. For the equivalen

18、t frequency and amplitude modulation corresponding to conditions A and Z in voice-frequency telegraph equipment, see Recommendation V.l and the relevant Series R Recommendations. NOTES 1 The level and polarity of voltage and current corresponding to conditions A and Z (e.g. in the local end with its

19、 The terms “start” and “stop”, “space” and “mark” have also been used to describe conditions A and Z respectively termination) are national options and hence are not defined internationally. (see definition 31.37R.140). 2 4 Particular combinations 4.1 In accordance with Recommendations S.6, S.8 and

20、the Series U Recommendations, WRU signal (who are you? combination Nos. 30 and 4) is used to operate the answerback unit of the corresponding instrument in the international telex and gentex services, and may also provide a printed symbol (as in Table 2). 4.2 Since some Administrations assign combin

21、ation Nos. 6, 7 and 8 in figure case for internal use whereas others do not, it is desirable to avoid varying interpretation in these circumstances that might result if they were used freely in international services. Consequently the use of combination Nos. 6, 7 and 8 in figure case is not defined

22、and therefore should not be used in international services, except by direct agreement between Administrations; and it is recommended - - that, in all services, they should be shown in some special manner on the keyboards; and that services in which they are not used should place on the secondary po

23、sition on the printing blocks (or on the equivalent mechanism) an arbitrary sign, for the letters F, G and H such as, for instance, a square. The appearance of such sign on the paper is to indicate an abnormal impression. 4.3 4.4 installation in the “letter” or “figure” position, so that Combination

24、 No. 10 “audible signal“, may also provide a printed symbol (as in Table 2). Combinations Nos. 29 and 30, “letter-shift” and “figure-shift”, respectively, are used to place the terminal - any combination No. 1 to 26 received engenders a printed signal in the “letter” case (second column of Table 1)

25、if the last shift signal received is a “letter-shift signal; any combination No. 1 to 26 received engenders a printed signal in the “figure” case (third column of Table 1) if the last shift signal received is a “figure-shift” signai”, except as noted for combinations Nos. 4 and 10 in 4.1 and 4.3. -

26、To ensure that terminal equipments located at both ends of a telex call are in the appropriate shift position, in new terminals, and as far as possible in existing terminals, the first combination to be transmitted, either after reception of characters or when commencing transmission, shall be eithe

27、r “letter-shift or “figure-shift” (i.e. combination No. 29 or combination No. 30). 4.5 Combinations Nos. 29 (letter-shift), 30 (figure-shift) and 32 (all-space, null or no tape perforation) shall not affect the spacing movement of terminal machines, except where their reception is indicated by print

28、ing a symbol, as mentioned in clause 5 below. 2 Recommendation S.1 (03/93) TABLE 16.1 International Telegraph Alphabet No. 2 (ITA2) 4.6 4.6.1 Use of capital and small letters In ITA2, it is possible to use teleprinters with two series of letter characters, capital and small letters. Recommendation S

29、.l (03/93) 3 ITU-T RECMN*S-L 93 = 48b2591 0588731 Tb1 9 4.6.2 4.6.3 characters. It is possible to use sequences of the shift combinations of ITA2 for transfer from one series to the other. If this possibility is used, it is essential to obtain compatibility with teleprinters having only one series o

30、f letter 4.7 Use of combination No. 32 4.7.1 Recommendations U. 1 1, U.20, U.22 and S.4. 4.7.2 international telex service. Combination No. 32 can be used in certain sequences of switching signals; these uses are set out in Combination No. 32 must not be used during the phase of communication (after

31、 a call is set up) in the 4.7.3 Combination No. 32 can be used during the phase of communication after a call is set up in domestic national service or by bilateral agreement between two Administrations, as a command signal for certain functions, e.g. transfer to a national alphabet other than ITA2.

32、 4.7.4 within ITA2, nor for transfer from one international telegraph alphabet to another. Combination No. 32 must not be used for transfer from one form of characters to another while remaining 5 Where a graphic indication of the reception or transmission of certain control characters is required,

33、this should be effected by printing the symbols shown in Table 2. Graphic representation of control characters TABLE US.1 Printed symbols for control characters Who are you? (WU) All-space: Null 32 Either U Nu NOTES 1 2 displayed line. The pictorial representation shown is a schematic of a, which may also be used when equipment allows. Each alphabetical representation is to be considered as a single symbol. It may occupy one position on a printed or 4 Recommendation S.l (03/93)