GOST ISO 4097-2013 Rubber ethylene-propylene-diene (EPDM) Evaluation methods《三元乙丙橡胶 (EPDM) 橡胶 评价方法》.pdf

《GOST ISO 4097-2013 Rubber ethylene-propylene-diene (EPDM) Evaluation methods《三元乙丙橡胶 (EPDM) 橡胶 评价方法》.pdf》由会员分享，可在线阅读，更多相关《GOST ISO 4097-2013 Rubber ethylene-propylene-diene (EPDM) Evaluation methods《三元乙丙橡胶 (EPDM) 橡胶 评价方法》.pdf（16页珍藏版）》请在麦多课文档分享上搜索。

1、 -(EPDM) (ISO 4097:2007, IDT) , ()INTERSTATE COUNCIL FOR STANDARDIZATION, METROLOGY AND CERTIFICATION(ISC)ISO 40972013, 1.092 . 1.22009 . , - . , , -, 1 160 - , - () - , 42 3 , (- 27 2013 . 59-) : ( 3166) 00497 ( 3166) 00497 AMBYKGMDRUTJUA - 4 ISO 4097:2007 Rubber,ethylene-propylene-diene (EPDM) Eva

2、luation procedure - (EPDM). . SC 3 () ISO/TC 45 (ISO). (en). , - , , , . -. - . (IDT)5 14 2014 . 147- ISO 40972013 1 2016 .6 II ISO 40972013 -, - . () . , - - , 2014 -, III ISO 409720131 .12 13 24 25 .26 .67 78 79 .9 () .1011IV ISO 40972013 - (EPDM) Rubber, ethylene-propylene-diene (EPDM). Evaluatio

3、n methods - . , . - , , .1 - , - , . , , -, - .2 . - , ( ).ISO 37 Rubber, vulcanized or thermoplastic Determination of tensile stress-strain properties (- . )ISO 247:2006 Rubber Determination of ash (. )ISO 248 Rubber raw Determination of volatile-matter content (. )1)ISO 289-1 Rubber, unvulcanized

4、Determinations using a shearing-disc viscometer Part 1:Determination of Mooney viscosity ( . - . 1: )ISO 1795 Rubber, raw natural and raw synthetic Sampling and further preparative procedures (- . )ISO 2393 Rubber test mixes Preparation, mixing and vulcanization Equipment and procedures( . , . )ISO

5、3417 Rubber Measurement of vulcanization characteristics with the oscillating disc curemeter(. )ISO 6502 Rubber Guide to the use of curemeters (. -)1) ISO 248-1:2011 Rubber raw Determination of volatile-matter content Part 1: Hot-mill method andoven method (. . 1. ).1 ISO 40972013 201601013 ISO 2352

6、9 Rubber General procedures for preparing and conditioning test pieces for physical testmethods (. - )3.1 1,5 ISO 1795.3.2 ISO 1795.4 4.1 ISO 289-1 , 3.2 ( ). (50 c177 5) C (35 c177 5) C. - . ML (1 + 4) - 125 C, (100 C 150 C) / (1 + 8) .4.2 ISO 248.4.3 ISO 247 ( A B).5 5.1 1 6 :- 1 EPDM , , - 67 % .

7、;- 2 EPDM , , - 67 % .;- 3 EPDM , , ;- 4 EPDM , 50 - 100 ;- 5 EPDM , 50 80 - 100 ;- 6 EPDM , 80 100 . . , , - . 1 EPDM 123456 EPDM 100,00 100,00 100,00 100,00 + xa)100,00 + yb)100,00 + zc) 1,00 1,00 1,00 1,00 1,00 1,00 d)80,00 100,00 40,00 80,00 80,00 150,00 ASTM, 103e)50,00 75,00 50,00 xa)2 ISO 409

8、72013 1123456 5,00 5,00 5,00 5,00 5,00 5,00 1,50 1,50 1,50 1,50 1,50 1,50- (TMTD)f)1,00 1,00 1,00 1,00 1,00 1,00(MBT) 0,50 0,50 0,50 0,50 0,50 0,50 239,00 284,00 149,00 239,00 189,00 + yb)259,00 + zc)a)x 100 , 50 .b)y 100 , 50 80 .c)z 100 , 80 - .d) (IRB).e) 0,92 /3 Sun Refining and Marketing Compan

9、y - R.E. Carroll Inc., 1570 North Olden Avenue Ext, Trenton, NJ 08638, USA. - Sunoco Overseas Inc., 1801 Market Street, Philadelphia, PA 19103-1699, USA. , .f) TMTD IRM 1, - Forcoven Products Inc., 22010 E. Martin Dr., Porter, TX 77365, USA.5.2 5.2.1 , - ISO 2393.5.2.2 5.2.2.1 :- A ;- B ;- C . - - ,

10、 , . EPDM B .5.2.2.2 A 5.2.2.2.1 , ,a) , 150 C 5 . -, 8 / (77 /), 0 03 ISO 40972013b) , , , - . 0,5 0,5c) 2,5 3,0d) , - . 0,5 3,5e) , 150 C 5 , , - 1,5 5,0 ( ) 5,0f) 2,5 - (50 c177 5) C. (. ISO 2393). 0,5 % 1,5 %, - .g) 30 24 - ISO 23529.5.2.2.2.2 , ,a) (40 c177 5) C. , - 8 / (77/) 0 0b) , 5.2.2.2.1, , - . 0,5 0,5c) , 110 C 2 , , 1,5 2,0 , 2,0d) 0,8 - (50 c177 5) C.e) .f) 6 . (. ISO 2393). 0,5 % 1,5 %, .g) .h) 2,2 ISO 37.i) 30 24 - ISO 23529.5.2.2.3 B , . (50 c177 5) C. , , (. ). . , , , .4 ISO 40972013 ,