GMW GMW16601-2012 Grease Mineral Oil and Lithium Soap Thickener Issue 2 English.pdf

《GMW GMW16601-2012 Grease Mineral Oil and Lithium Soap Thickener Issue 2 English.pdf》由会员分享，可在线阅读，更多相关《GMW GMW16601-2012 Grease Mineral Oil and Lithium Soap Thickener Issue 2 English.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 WORLDWIDE ENGINEERING STANDARDS Material Specification GMW16601 Grease, Mineral Oil and Lithium Soap Thickener Copyright 2012 General Motors Company All Rights Reserved August 2012 Originating Department: North American Engineering Standards Page 1 of 5 1 Scope 1.1 Material Description. This specif

2、ication defines grease composed of mineral oil and lithium soap thickener and having consistency of one, two or three (1, 2 or 3). 1.2 Symbols. Not applicable. 1.3 Typical Applications. Grease defined by this specification may be used on wheel bearings and/or chassis components (including ball joint

3、s, steering pivots, and universal joints). 1.4 Remarks. Suitability with plastics and elastomers must be verified. This grease is not suitable for use with elastomers made from buna, butyl, ethylene propylene diene monomer (M-class) (EPDM), or natural rubber. 2 References Note: Only the latest appro

4、ved standards are applicable unless otherwise specified. 2.1 External Standards/Specifications. ASTM D217 ASTM D1743 DIN 51350 DIN ISO 2137 ASTM D566 ASTM D2265 DIN 51802 DIN ISO 2176 ASTM D1264 ASTM D2596 DIN 51807 ASTM D1742 ASTM D6138 DIN 51817 2.2 GM Standards/Specifications. GMW3059 2.3 Additio

5、nal References. TMC003 Material Safety Data Sheet guidance documents (available at ). 3 Requirements 3.1 Performance Requirements. 3.1.1 Base oil. Mineral oil shall be used as the base oil. 3.1.2 Thickener. Lithium-based soap shall be used as the thickener. The type of soap shall be characterized as

6、 being lithium, lithium 12-hydroxystearate, or lithium complex. 3.1.3 Specific requirements. The grease shall meet the requirements listed in Appendix A, Tables A1 and A2. 3.2 Performance Levels. 3.2.1 Designations. Performance level designations for chassis grease are CA and CB. Performance level d

7、esignations for wheel bearing grease are WA and WB. 3.2.2 Nomenclature. Grease type, performance levels and consistency are defined using the following nomenclature: 1XY# where: 1 means mineral oil-based with lithium soap thickener XY are letters designating performance levels shown in 3.2.1 # is a

8、number from one to three (1 to 3) indicating National Lubricating Grease Institute (NLGI) consistency. (Example: 1CB2 is mineral oil with lithium thickener, CB performance level, NLGI consistency 2.) Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for Re

9、saleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16601 Copyright 2012 General Motors Company All Rights Reserved August 2012 Page 2 of 5 4 Manufacturing Process Not applicable. 5 Rules and Regulations 5.1 Legal Regulations. All materials

10、must satisfy applicable laws, rules, regulations and recommendations valid in the country of usage. 5.2 Language. In the event of conflict between the English and domestic language, the English language shall take precedence. 5.3 Inspection and Rejection. All shipments of material or parts under con

11、tract or purchase order manufactured to this specification shall be equivalent in every respect to the initial samples approved by Engineering. There shall be no changes in either formulation or manufacturing processes permitted without prior notification and approval by Engineering. Lack of notific

12、ation by the supplier constitutes grounds for rejection of any shipment. While samples may be taken from incoming shipments and checked for conformance to this specification, the supplier shall accept the responsibility for incoming shipments meeting this specification without dependence upon purcha

13、sers inspection. The series of tests used to approve each batch of product along with acceptance limits will be agreed upon by the purchaser and seller. The laboratory providing the certificate of analysis must also participate in a proficiency testing program (round robin) that is approved by the F

14、uels, Fluids, and Lubricants Global Subsystem Leadership Team (GSSLT) or designate. The Fuels, Fluids, and Lubricants GSSLT or designate must receive copies of the proficiency testing reports directly from the test program administrator. 5.4 Initial Source Approval. No shipment shall be made by any

15、supplier until representative initial production samples have been approved by the Fuels, Fluids, and Lubricants Global Subsystem Leadership Team or designees meeting the requirements of this specification. 5.5 Material Safety Data Sheets/Safety Data Sheets (MSDS/SDS). For new product submissions, o

16、r when a change in chemical composition of an existing product has occurred, a complete copy of the Material Safety Data Sheet/Safety Data Sheet must be submitted in compliance with the Globally Harmonized System of Classification and Labeling of Chemicals (GHS) requirements or other country-specifi

17、c MSDS/SDS requirements. In addition, product MSDS/SDS submissions must be in compliance with specific country General Motors TMC003 Material Safety Data Sheet/Safety Data Sheet guidance documents where available. 5.6 All materials supplied to this standard must comply with the requirements of GMW30

18、59, Restricted and Reportable Substances for Parts. 6 Approved Sources Engineering qualifications of an approved source are required for this standard. Only sources listed in the GM Materials File (MATSPC) under this standard number have been qualified by Engineering as meeting the requirements of t

19、his standard. For other GM locations, the responsible Engineering group should be contacted to obtain the approved source in that individual country. 7 Notes 7.1 Glossary. MATSPC: Global repository of GM approved materials for corresponding GM Engineering Standards. 7.2 Acronyms, Abbreviations, and

20、Symbols. CV Constant Velocity EPDM Ethylene Propylene Diene Monomer (M-class) GHS Globally Harmonized System of Classification and Labeling of Chemicals GSSLT Global Subsystem Leadership Team MSDS Material Safety Data Sheet NLGI National Lubricating Grease Institute SDS Safety Data Sheet Copyright G

21、eneral Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16601 Copyright 2012 General Motors Company All Rights Reserved August 2012 Page 3 of 5 8 Coding Sys

22、tem This standard shall be referenced in other documents, drawings, etc., as follows: Material per GMW16601 9 Release and Revisions This standard was originated in May 2011. It was first approved by the Fuels, Fluids, and Lubricants Global Subsystem Leadership Team (GSSLT) in September 2011. It was

23、first published in October 2011. Issue Publication Date Description (Organization) 1 OCT 2011 Initial publication. 2 AUG 2012 Added Regional Cross Reference Chart. (Fuels, Fluids, and Lubricants Global Subsystem Leadership Team) Cross Reference of Regional Specifications Specification Region GMW Cat

24、egory Equivalent Specification Comments 9273141 SGM 1CB2 B 040 2084 9309803 GMB 1WA3 B 040 0881 9309823 GMB 1WB2 B 040 0886 9309914 GMB 1WA1 B 040 0265 9309918 GMB 1WB2 B 040 1109 9309932 GMB 1WA3 B 040 0625 9309938 GMB 1WB2 B 040 0886 9309973 GMB/SGM 1CB2 B 040 0852 9309982 GMB 1WB2 B 040 0857 9309

25、984 GMB 1WB2 B 040 0886 9309986 GMB 1WB2 B 040 0886 9309995 GMB 1WB2 B 040 0886 9309998 GMB 1WB2 B 040 0886 9310000 GMB 1WB2 B 040 0886 94545052 GMK 1CB1 EDS-M-8101 94545053 GMK/SGM 1CB1 EDS-M-8102 94545055 GMK 1CB2 EDS-M-8105 94545061 GMK 1CB3 EDS-M-8118 94545071 GMK 1CB1 EDS-M-8138 94545074 GMK 1C

26、B3 EDS-M-8143 Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16601 Copyright 2012 General Motors Company All Rights Reserved August 2012

27、 Page 4 of 5 Specification Region GMW Category Equivalent Specification Comments 95975163 GMK 1WB2 9985038 GMNA 1CB2 Must carry NLGI LB certification 9985254 GMNA 1WA2 Must carry NLGI GC-LB certification 9986154 GMNA 1CB2 2 7% polyethylene HN1147 GM Holden 1CB2 HN1225 GM Holden 1CB1 10% Zinc Oxide H

28、N1271 GM Holden 1CB2 10% Molybdenum Disulphide HN1323 GM Holden 1CB2 30% Graphite HN1327 GM Holden 1CB3 HN1416 GM Holden 1CB2 3% Molybdenum Disulphide HN1421 GM Holden 1CB1 HN1729 GM Holden 1WA3 HN1815 GM Holden 1CB2 HN1923 GM Holden 1CB2 HN2073 GM Holden 1WB2 HN2480 GM Holden 1WB2 Copyright General

29、 Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-GM WORLDWIDE ENGINEERING STANDARDS GMW16601 Copyright 2012 General Motors Company All Rights Reserved August 2012 Page 5 of 5 Appendix A A1 Cons

30、istency and Properties A1.1 Consistency for Performance Levels 1CA1, 1CB1, 1WA1, 1WB1, 1CA2, 1CB2, 1WA2, 1WB2, 1CA3, 1CB3, 1WA3, 1WB3. Table A1: Consistency for Performance Levels Consistency Test Method Units 1CA1, 1CB1, 1WA1, 1WB1 1CA2, 1CB2, 1WA2, 1WB2 1CA3, 1CB3, 1WA3, 1WB3 Worked Penetration AS

31、TM D217 DIN ISO 2137 mm/10 310 to 340 265 to 295 220 to 250 A1.2 Properties for Performance Levels 1CA1, 1CB1, 1WA1, 1WB1, 1CA2, 1CB2, 1WA2, 1WB2, 1CA3,1CB3, 1WA3, 1WB3. Table A2: Properties for Performance Levels Note 1, Note 2, Note 3 Property Test Method Units 1CA1 1CA2 1CA3 1CB1 1CB2 1CB3 1WA1 1

32、WA2 1WA3 1WB1 1WB2 1WB3 Dropping Point ASTM D566 ASTM D2265 DIN ISO 2176 C 125 to 150 150 to 200 200 to 250 250 Corrosion Resistance ASTM D1743 or ASTM D6138 DIN 51802 Rating Rating Maximum Pass 1 Pass 1 Pass 1 Pass 1 Extreme Pressure, Weld Point ASTM D2596 DIN 51350 N (kgf), Minimum 1960 (200) 1960

33、 (200) 1960 (200) 1960 (200) Extreme Pressure, Load Wear Index ASTM D2596 DIN 51350 N (kgf), Minimum 295 (30) 295 (30) 295 (30) 295 (30) Oil Separation ASTM D1742 DIN 51817 % Maximum 10 10 6 6 Water Resistance ASTM D1264 or DIN 51807 % Maximum at 80 C Valuation after 3 h at 90 C Not applicable Not a

34、pplicable Not applicable Not applicable 15 1 to 90 15 1 to 90 Note 1: Corrosion resistance shall be met using ASTM D1743 or ASTM D6138/DIN 51802. Note 2: Water resistance shall be met using ASTM D1264 or DIN 51807. Note 3: Deviations. Grease for constant velocity (CV) joints is permitted an oil separation value of 16% maximum. Copyright General Motors Company Provided by IHS under license with General Motors CompanyNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-