GMKOREA EDS-T-4530-2011 Test Procedure Headrest Head Contacting Surface.pdf

《GMKOREA EDS-T-4530-2011 Test Procedure Headrest Head Contacting Surface.pdf》由会员分享，可在线阅读，更多相关《GMKOREA EDS-T-4530-2011 Test Procedure Headrest Head Contacting Surface.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING STANDARDS Test Procedure LIMITED USE EDS-T-4530 Test Procedure Headrest Head Contacting Surface Do Not Use on New Program; No Replacement. Headrest %. 9E=+95 4G 98 88x 7 , F6* 72T8p) F$ . 1.1 +95 . G- % 4 +l*8 7xG* 88F Headrest8 H3L2e G88x +958p) F$ . 1.2 957 -88 . Headrest 4 .=%P +& Se

2、at7 957F$ . 2 4) E:4 / :0 : C-H +d%P 9I8 6# F 48 07 38%P E:48x 957F$ . 2.1 17 E:4 / . None 2.2 GM E:4 / . None 2.3 dA E:4 / . None 3 4G 88 3.1 4G 8/x . 3.1.1 Seat* 4= M8 9IF3L 8# Jig. 3.1.2 3LD 9I-L . 3.1.3 F:E 84 8? . F:E8x 84F# 8?) 0.5 Kgf8!* ?U9I F 3L 866 F$ . 3.1.4 F:E84 JIG. Head Form (: 165 mm

3、). 3.2 4G D . 4E ASSY 1B8 Headrest* 3P 81 4G F$ . 4 4G 9 Sleeve Rod7 3L:F -F8p) 30 Kg8 F:E8x 84F$ . 4.3.2 F:E8x 9P G Headrest7 ,o6 8# $*8 +958x ?U9IF$ . Figure 1 / ,* 1 5 Data 5.1 Evaluations. Contact area between the headrest and head form shall not be smaller than 50 cm2. 6 Safety This standard ma

4、y involve hazardous materials, operations, and equipment. This standard does not propose to address all the safety problems associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulator

5、y limitations prior to use. 5 4G $8Bd 5.1 D4 . Headrest 7t Head Form8 9E= +958 50 cm2 81 8 . 6 6|987 $4F 7 9 ., E:48t 88G ,p: , 86 , 8/x &%8x E FF 3L 8$ . ., E:48t 87 $4F 170 4)%P +& 6|98 ,l9P8 F8x 9P4F:# 6#$ . &d(2P 17 987 95FF 6|980 I 1B* 9DF , -18 9PF 728 957 7 .* 9IF# 8t ., E:4 1788 =y8 1F8$ . G

6、M KOREA ENGINEERING STANDARDS EDS-T-4530 Copyright 2011 General Motors Company All Rights Reserved September 2011 Page 3 of 3 Version : 3 7 Notes 7.1 Glossary. Not applicable. 7.2 Acronyms, Abbreviations, and Symbols. Not applicable. 8 Coding System This standard shall be referenced in other documen

7、ts, drawings, etc., as follows: Test to EDS-T-4530 9 Release and Revisions This standard was originated in May 1998. It was first approved by Engineering Standard Committee in May 1998. It was first published in May 1998. 7 768 9I8 7.1 98,l 76 . F$-1F 68 . 7.2 66 -C dGl . F$-1F 68 . 8 Ed - $* ,l2P!

8、$+ &%72P ., E:48 87%T &# $80 M8 EdF$ . Test to EDS-T-4530 9 9P9I -C P9I 8)Y ., E:48t 1998 “x 5 87 E:4 -Gl4 .7 %L6 , d3TE:41,h7 8F 1998“x 587 38%L6$ . ., E:48t 1998“x 587 ) 9P9I / -PF%L6$ . Issue / P9I8)Y Publication Date / 38 88 Description (Organization) / 9PP9I76 (:04.2P ) 3 SEP 2011 Apply new Engineering Standard Template. Limited use with no replacement (Interior Subsystem Validation Team) / 4 d3TE:4 64 957 . F9I957 ($4=E:4 68 ) =* (Interior.ED4D4 )