FORD WSS-M9G24-A1-2016 LUBRICANT ALUMINUM SHEET TO BE USED WITH FORD WSS-M99P1111-A .pdf

《FORD WSS-M9G24-A1-2016 LUBRICANT ALUMINUM SHEET TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M9G24-A1-2016 LUBRICANT ALUMINUM SHEET TO BE USED WITH FORD WSS-M99P1111-A .pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 3 2016 06 27 Revised See Summary of Revisions K. Morgan, NA 2015 03 26 Revised See Summary of Revisions C. Mracna, NA 2013 02 01 Activated C. Mracna, NA Controlled document at www.MATS Copyright 2016, Ford Global Technologies, LLC Page 1

2、 of 4 LUBRICANT, ALUMINUM SHEET WSS-M9G24-A1 1. SCOPE This specification defines the requirements for lubricant coatings intended to be used for the stamping of aluminum sheet. The lubricant coatings shall be specified in conjunction with the appropriate base aluminum and surface treatment specifica

3、tions. 2. APPLICATION This specification was originally released for a hot melt lubricant to be used for stamped aluminum automobile body parts. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List

4、(ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 PRODUCT CHARACTERISTICS 3.2.1 Appearance, 20C Light Brown to Dark Brown (Visual) 3.

5、2.2 Melting Point 44 - 52 C (ASTM D127) 3.2.3 Kinematic Viscosity at 82.2C 6.4 8.1 mm2/s (ASTM D445, DIN 51562, ISO 3104) 3.2.4 Saponification Value 12.7 18.0 mg/g (ASTM D94, DIN 51559-1, or technical equivalent) 3.2.5 Percent Free Fatty Acidity (as oleic) 0.0 2.5 % (Quaker GTM 1000, or technical eq

6、uivalent) 3.3 PERFORMANCE OR PROCESS CHARACTERISTICS 3.3.1 Coating Weight, average 0.35 0.85 g/m2/side (ASTM F2217, or technical equivalent) ENGINEERING MATERIAL SPECIFICATION WSS-M9G24-A1 Copyright 2016, Ford Global Technologies, LLC Page 2 of 4 3.2.3 Bake Staining (FLTM AB 107-01) There shall be n

7、o objectionable bake staining following a T82 tempering process per FLTM AB 107-01 based on a jury evaluation of at least two people from Ford Product Development Engineering 3.4 COATING UNIFORMITY The coating shall be uniformly applied across the substrate surface. The applicator will be responsibl

8、e and will document the measurable in the control plan. The product shall not be applied in an application system with temperatures below 54 C. The temperature of the substrate shall not exceed 50C for longer than 20 minutes post application. 3.5 STRUCTURAL ADHESIVE PERFORMANCE REQUIREMENTS Material

9、 supplied to this specification shall demonstrate acceptable stress durability performance as detailed in the adhesive performance specification, WSS-M2G410-A, Sec. 3.5.2, up to a max coating weight of 1.25 g/m2/side. 3.6 SEALANT PERFORMANCE REQUIREMENTS Material supplied to this specification shall

10、 demonstrate acceptable performance as detailed in the applicable sealant material specification defined by Product or Materials Engineering, up to a max coating weight of 1.25 g/m2/side. 3.7 PAINTABILITY The paintability requirements of the appropriate base aluminum material specification shall app

11、ly for a max coating weight of 1.25 g/m2/side. 3.8 WELDABILITY (FLTM BB 113-07) The weldability requirements of the appropriate base aluminum material specification shall apply for a max coating weight of 1.25 g/m2/side. The weldability shall meet the performance requirements outlined in FLTM BB 113

12、-07. Final approval of weldability will be determined by the affected manufacturing facility. 3.9 SHELF LIFE The lubricated aluminum substrate shall have a shelf life of 1 year when transported and stored in the manufacturers recommended environmental conditions. 3.10 FUNCTIONAL APPROVAL Materials b

13、eing evaluated for approval to this specification shall be subjected to a production trial. Functional trial results must be approved by the affected stamping and assembly operation and Design Engineering. Results shall be made available to Materials Engineering prior to material approval. 4. GENERA

14、L INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications. ENGINEERING MATERIAL SPECIFICATION WSS-M9G24-A1 Copyright 2016, Ford Global Technologies, L

15、LC Page 3 of 4 4.1 FOURIER TRANSFORM INFRARED SPECTROSCOPY (FTIR) (ASTM E1252) An FTIR spectrum shall be submitted upon initial product validation and made available upon request. 4.2 NEEDLE PENETRATION 50 - 80 mm/10 (ASTM D1321) 4.3 FLASH POINT 180 C min (ASTM D92) 4.4 CONDENSING HUMIDITY RESISTANC

16、E, 12 WEEKS Rating 6 min (FLTM BI 104-02, except 50C, evaluation per ASTM D610) 4.5 APPROVAL OF MATERIALS Suppliers desiring approval of their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a

17、 completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum

18、of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis, Control Plans, Certification testing) with Ford. 4.6 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon

19、which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affect the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materia

20、ls Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval, SREA. For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production V

21、erification (PV) and Production Part Approval Process (PPAP) sign off must be kept until Job 1. 4.7 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the

22、Restricted Substance Management Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS 2016 06 27 Sec.3 &4 - Removed WSS-M99P1111-A and moved those requirement

23、s directly into this specification. Sec. 3.2 Added Kinematic Viscosity and revised color. Sec 4.2 Added Needle Penetration ENGINEERING MATERIAL SPECIFICATION WSS-M9G24-A1 Copyright 2016, Ford Global Technologies, LLC Page 4 of 4 2015 03 26 Sec. 3.3 Changed Coating Weight from 0.50 1.00 to 0.35 0.85 g/m2/side Sec. 3.7 Added max coating weight requirement Sec. 3.8 Added max coating weight requirement 2014 06 19 Sec. 3.4 Changed “Supplier” to “Applicator”. Changed substrate temp from 40C to 50C.