FORD WSS-M3H199-A1-2017 CARPET 199 PATTERN POLYESTER NON WOVEN DILOUR POLYETHYLENE BACKED 680 g m2 (20 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf
《FORD WSS-M3H199-A1-2017 CARPET 199 PATTERN POLYESTER NON WOVEN DILOUR POLYETHYLENE BACKED 680 g m2 (20 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf》由会员分享,可在线阅读,更多相关《FORD WSS-M3H199-A1-2017 CARPET 199 PATTERN POLYESTER NON WOVEN DILOUR POLYETHYLENE BACKED 680 g m2 (20 oz) NOMINAL FACE TO BE USED WITH FORD WSS-M99P1111-A .pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev 00 2017 08 01 Released K.Cheng, AP Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 4 CARPET, 199 PATTERN, POLYESTER, NON WOVEN, DILOUR, WSS-M3H199-A1 POLYETHYLENE BACKED 680 g/m2 (20 oz) NOMINAL FAC
2、E 1. SCOPE The materials defined by this specification are Dilour, non-woven carpets of good quality and uniform composition. The face fiber is virgin polyester and it is back coated with the appropriate weight of polyethylene. 2. APPLICATION This specification was originally released for Ford Focus
3、 MY2018 floor carpet. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other documents. The list of approved sour
4、ces is located within Ford at or available externally through a Ford Materials Engineer. 3.2 CONDITIONING AND TEST CONDITIONS All test values are based on material conditioned for not less than 24 h prior to testing in a controlled environment of 23 +/- 2 C and 50 +/- 5% relative humidity. Testing
5、of the material should occur in the conditioning environment or soon after removal. 3.3 PERFORMANCE CRITERIA 3.3.1 In addition to the requirements listed herein, the end-item carpet shall be tested to WSS-M8P16-B and any additional SDS requirements. The details for each of the supplier specific cons
6、tructions shall be documented in the supplement attached and uploaded into the scanned data package. 3.3.2 Vehicle Interior Environment Quality Materials/Component Performance Requirements Materials used in interior applications must meet the requirements outlined in WSS-M99P2222-D1/ latest. Data mu
7、st be provided at the appropriate program milestone. 3.4 SAMPLE SELECTION All evaluations shall be conducted on test specimens taken from finished roll goods (including substrate layers) prior to any subsequent operations, such as molding. 3.5 APPEARANCE The color, pattern, and gloss shall match the
8、 approved Corporate Design master sample. ENGINEERING MATERIAL SPECIFICATION WSS-M3H199-A1 Copyright 2017, Ford Global Technologies, LLC Page 2 of 4 3.6 COMPOSITION 3.6.1 Face Fiber 88% Polyester (ASTM D276) 3.6.2 Binder Fiber 12% Low Melt Polyester (ASTM D276) 3.6.3 Primary Backing Polyethylene (AS
9、TM D276) 3.7 METHOD OF DYEING Solution dyed 3.8 CONSTRUCTION 3.8.1 Face Fiber 16.7 denier (ASTM D 1244) 3.8.2 Binder Fiber 4 denier (ASTM D 1244) 3.9 THICKNESS* 4.0+/-0.5 mm (ISO 1765) *Face thickness prior to molding 3.10 WEIGHT 3.10.1 Face Fiber and Binder Fiber (612-748) g/m2 (ASTM D5848) (18 22.
10、1) oz 3.10.2 Primary Backing (135-165) g/m2 (ASTM D5848) (4 4.9) oz Weight tolerances approved for each suppliers construction can be found in the scanned data package. 4. GENERAL INFORMATION This information given below is provided for clarification and assistance in meeting the requirements of thi
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDWSSM3H199A12017CARPET199PATTERNPOLYESTERNONWOVENDILOURPOLYETHYLENEBACKED680GM220OZNOMINALFACETOBEUSEDWITHFORDWSSM99P1111APDF

链接地址:http://www.mydoc123.com/p-753381.html