FORD WSS-M1H728-A-2008 FABRIC STARWAY JACQUARD WOVEN TO BE USED WITH FORD WSS-M99P1111-A 《STARWAY图案的提花机织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSS-M1H728-A-2008 FABRIC STARWAY JACQUARD WOVEN TO BE USED WITH FORD WSS-M99P1111-A 《STARWAY图案的提花机织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1H728-A-2008 FABRIC STARWAY JACQUARD WOVEN TO BE USED WITH FORD WSS-M99P1111-A 《STARWAY图案的提花机织织物 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2008 12 03 N-STATUS No Replacement L. Schmalz, FNA / M. Montgomery, FOE 2003 03 21 Revised Para 3.0 inserted ; Para 3.1, 3.2, 3.3, 3.10, 3.11, 4 deleted 1997 10 30 Activated N. Komatsu Printed copies are unc

2、ontrolled Page 1 of 2 Copyright 2008, Ford Global Technologies, Inc. FABRIC, STARWAY, JACQUARD WOVEN WSS-M1H728-A NOT TO BE USED FOR NEW DESIGN 1. SCOPE The material defined by this specification is a woven jacquard polyester face fabric. 2. APPLICATION This specification was released originally for

3、 material used as an interior trim fabric for the 1998 MY BE146. 3. REQUIREMENTS In addition to the requirements listed herein, the fabric shall meet all requirements of WSS-M8P18-A1/A2/A3/A4. 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to th

4、e Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.4 FABRIC CONSTRUCTION 3.4.1 Fabric Count, +/- 5 % tolerance (ASTM D 3775) Warp 265 ends/10 cm Weft 250 picks/10 cm 3.4.2 Fabric Weight, range 360 +/- 20 g/m2(FLTM BN 106-01) 3.5 COMPOSITION (ASTM D 629) Fabric 100 % polyes

5、ter ENGINEERING MATERIAL SPECIFICATION WSS-M1H728-A Page 2 of 2 Copyright 2008, Ford Global Technologies, Inc. 3.6 YARN CONSTRUCTION (ASTM D 1244) Warp 830 dtex f132 (polyester, semi- dull, round, air texturized) Weft 820 dtex f192 (polyester, semi-dull, round, air texturized) 730 dtex f144 (polyest

6、er, bright, trilobal, air texturized) 3.7 METHOD OF DYEING Yarn dyed and spun dyed or as approved by Materials Engineering 3.8 FINISHED OPERATIONS As approved by Materials Engineering 3.9 FLAMMABILITY (ISO 3795/SAE J369) Burn Rate, max 100 mm/minute Note: Not required on face fabric when used as a f

7、ully bonded composite. 5. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification 5.1 Purchase departments will ensure that both materials defined in this specification and shipped to any one assembly plant will be produced by one supplier only.