FORD WSS-M1C282-A2-2017 GREASE FLUORINATED LUBRICANT BRUSH APPLICATOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M1C282-A1).pdf

《FORD WSS-M1C282-A2-2017 GREASE FLUORINATED LUBRICANT BRUSH APPLICATOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M1C282-A1).pdf》由会员分享，可在线阅读，更多相关《FORD WSS-M1C282-A2-2017 GREASE FLUORINATED LUBRICANT BRUSH APPLICATOR TO BE USED WITH FORD WSS-M99P1111-A (Shown on FORD WSS-M1C282-A1).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Date Action Revisions Rev. 01 2017 05 08 Released A2 S. Gould, EU 2015 05 26 Released A1 S. Gould, EU Controlled document at www.MATS Copyright 2017, Ford Global Technologies, LLC Page 1 of 3 GREASE, FLUORINATED LUBRICANT, AEROSOL CANNISTER WSS-M1C282-A1 GREASE, F

2、LUORINATED LUBRICANT, BRUSH APPLICATOR WSS-M1C282-A2 1. SCOPE WSS-M1C282-A1 The material defined by this specification is a perfluoropolyether (PFPE) oil with a gaseous fluorinated propellant used to apply the lubricant as an aerosol spray. WSS-M1C282-A2 The material defined by this specification is

3、 a perfluoropolyether (PFPE) oil, with a brush applicator to apply the lubricant. 2. APPLICATION This specification was released originally for anti-squeak purposes for body interior. The aerosol spray produces a PFPE oil film on the surface which can feel oily to the touch. The lubricant is suitabl

4、e for operating temperatures between - 36 and + 204 C. 3. REQUIREMENTS 3.1 APPROVED SOURCES This specification requires the use of approved sources. Only the sources identified on the Ford Approved Source List (ASL) can be used when this specification is listed on the drawing, CAD file, or other doc

5、uments. The list of approved sources is located within Ford at or available externally through a Ford Materials Engineer. 3.2 CANNISTER WEIGHT at 20 C 3.2.1 Aerosol 125g Minimum 3.2.2 Brush Applicator 14 g Minimum 3.3 BASE OIL COLOR Clear/Transparent(Visual) 3.4 BASE OIL Density at 20 C 1.91 g/ml 3

6、.5 BASE OIL Viscosity at 40 C 150 170 mm2/s (ASTM D445) 4. GENERAL INFORMATION The information given below is provided for clarification and assistance in meeting the requirements of this specification. Contact for questions concerning Engineering Material Specifications.Grease approved to this spe

7、cification should have the following typical properties. 4.1 BASE OIL Viscosity Index 124 (ASTM D2270) 4.2 BASE FLUORINATED POLYMER 3 8% (According to formulation, ASTM D128) ENGINEERING MATERIAL SPECIFICATION WSD-M1C282-A1/A2 Copyright 2017, Ford Global Technologies, LLC Page 2 of 3 4.3 DROPPING PO

8、INT Not Available (ASTM D556, ASTM D2265, DIN ISO 2176) The test gives inaccurate results on solid thickened greases and would show a drop of oil from the cup at temperatures under 200 C even for greases that work at higher temperatures. 4.4 BASE OIL Density at 100 oC 1.76 g/ml 4.5 BASE OIL Viscosit

9、y at 100 oC 16 20 mm2/s (ASTM D445) 4.6 INTERFACE COMPATIBILITY 4.6.1 Chemical Attack to Painted Surfaces (FLTM BJ 126-01). Note: Not tested for initial application of this grease. PFPE / PTFE lubricants are generally inert to painted surfaces. Grease must be tested for chemical attack to painted su

10、rfaces for applications that come in contact with paint surfaces, ex. E-coat and powder coat. 4.6.2 Resistance to Stress Cracking (FLTM BO 127-03) Note: Not tested for initial application of this grease. PFPE / PTFE lubricants are generally inert to plastics. Grease must be tested for resistance to

11、stress cracking when used for additional applications that come in contact with polymers such as PC, ABS, PC+ABS, ASA or acrylic 4.6.3 Elastomer Compatibility, NBR (ASTM D 4289, DIN 53505, DIN 53504, 70 hrs, 100 C) Note: Not tested for initial application of this grease. PFPE / PTFE lubricants are g

12、enerally inert to rubber. Grease must be tested for elastomer compatibility when used for additional applications that come in contact with elastomers. Application specific elastomer should be used for testing instead of a reference elastomer. 4.7 APPROVAL OF MATERIALS Suppliers desiring approval of

13、 their materials shall first obtain an expression of interest from Purchasing, Design or Product Development, and Materials Engineering. The supplier shall submit a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstratin

14、g full compliance with all the requirements of the Material Specification. Tested material samples must be available for review upon request and kept for a minimum of one year. Upon request, the supplier will review the associated quality control documents (Process Failure Mode and Effects Analysis,

15、 Control Plans, Certification testing) with Ford. 4.8 SUPPLIERS ONGOING RESPONSIBILITY All materials must be equivalent in all characteristics to the material upon which approval was originally granted. Prior to making any changes to the material originally approved, whether or not such changes affe

16、ct the materials ability to meet the specification requirements, the supplier shall notify the affected Supplier Technical Assistance (STA), Purchasing, and Materials Engineering activities of the proposed changes (with reasons) by submission of a completed Suppliers Request for Engineering Approval

17、, SREA. ENGINEERING MATERIAL SPECIFICATION WSD-M1C282-A1/A2 Copyright 2017, Ford Global Technologies, LLC Page 3 of 3 For parts and components using Ford Engineering Material Specifications, all samples tested to the specifications for Design Verification (DV), Production Verification (PV) and Produ

18、ction Part Approval Process (PPAP) sign off must be kept until Job 1. 4.9 RESTRICTED SUBSTANCE MANAGEMENT STANDARD Substance restrictions imposed by regulations or Company direction applies to the materials addressed by this document. The restrictions are identified in the Restricted Substance Manag

19、ement Standard WSS-M99P9999-A1 which is updated yearly. It is the suppliers responsibility to comply with this standard on a continuing basis through IMDS and or GMAP reporting. 5. SUMMARY OF REVISIONS 2017 05 08 Released A2. Removed WSS-M99P1111-A and added those requirements directly to this document.