FORD WSF-M70J10-A-2005 PAINT POWDERED THERMOSETTING EPOXY TO BE USED WITH FORD WSS-M99P1111-A 《热固环氧树脂粉末状油漆 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSF-M70J10-A-2005 PAINT POWDERED THERMOSETTING EPOXY TO BE USED WITH FORD WSS-M99P1111-A 《热固环氧树脂粉末状油漆 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSF-M70J10-A-2005 PAINT POWDERED THERMOSETTING EPOXY TO BE USED WITH FORD WSS-M99P1111-A 《热固环氧树脂粉末状油漆 与标准FORD WSS-M99P1111-A一起使用 》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2005 07 29 Revised Inserted 3.0; Deleted 3.1, 3.2, 3.3, 3.7 and 4 1998 02 17 Revised Added para 3.4, Rev.3.5; Updated A. Vallabhanath 1993 08 31 Released NGA1E10269519007 A. Vallabhanath Printed copies are uncontrolled Copyright 2005, Ford Glo

2、bal Technologies, LLC Page 1 of 3 PAINT, POWDERED, THERMOSETTING EPOXY WSF-M70J10-A 1. SCOPE This specification defines the performance requirements for a thermosetting epoxy powder applied by the electrostatic method to a metal part. 2. APPLICATION This specification was released originally for coa

3、ting the wiper motor. This coating does not possess the ultraviolet stability which would permit exterior decorative applications. 3. REQUIREMENTS 3.0 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Productio

4、n Materials (WSS-M99P1111-A). Part producers using this material in their products, must use Ford approved materials and must conform to a process control plan which has been approved by STA and/or the relevant Materials Activity. 3.4 THERMOSETTING EPOXY POWDER CHARACTERISTICS 3.4.1 Hot Plate Gel at

5、 160 C 37 - 60 s Place teaspoon of powder onto temperature controlled plate at 160 C and begin timing. Constantly stroke the material in a back-and-forth motion with a metal spatula that was also preheated to 160 C. Stop timer when the material becomes stiff and ceases to move. Repeat test with new

6、sample, result must be within 10% of first test. Average of two tests must be within 37 - 60 s. 3.4.2 Glass Plate Flow 32 - 50 mm Weigh out sample of powder equivalent to 0.55X the specific gravity of the material within 0.1 g. Press sample into solid pellet 12.7 +/- 0.05 mm in diameter by 6.00 +/-

7、0.13 mm high. Place glass plate of at least 75 mm long in oven, fixtured at 48 from horizontal. Preheat oven and glass plate to 150 +/- 2 C. Open oven and place pellet at top of glass plate with enough force that pellet does not slide down plate. Allow material 10 minutes to flow, then remove plate

8、from oven and allow to cool to room temperature. Measure distance material flowed down glass plate. Must be 32 to 50 mm. Perform test two times. ENGINEERING MATERIAL SPECIFICATIONWSF-M70J10-APrinted copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 2 of 3 3.4.3 -80 Mesh Alpi

9、ne Sieve, min 100% Use appropriate U.S. Standard 200 mm diameter by 25 mm deep sieve and an Alpine Air-Jet sieve with differential pressure gauge. Measure empty sieve with cover and zero scale. Add 15.00 +/- 2.00 g of sample to sieve and place on Alpine Air-Jet sieve for 3.0 +/- 0.25 minutes with a

10、differential pressure setting of 140 - 215 mm of water. Remove sieve and reweigh. Calculate fraction of material that passed through sieve according to: 1 - (final weight/ initial weight), convert to percentage. If percentage reading scale is available, percentage can be read directly from scale. 3.

11、4.4 -140 Mesh Alpine Sieve, min 95% Use procedure from para 3.3.3. 3.4.5 -325 Mesh Alpine Sieve 52 - 78% Use procedure from para 3.3.3. 3.5 TEST PANELS Low carbon steel panels with a light iron phosphate coating shall be electrostatically sprayed with epoxy powder and cured at 135 C for 15 minutes.

12、3.5.1 Closed Anvil Impact Resistance Using a Gardner Laboratory Impact Tester or equivalent, set up with a flat anvil and a 15.8 mm punch, drop a 1.81 kg weight from a height of 1.016 m onto the test panel for an impact value of 1.84 kg/m. The coating must not show any cracking or loss of adhesion.

13、3.5.2 Adhesion No flaking or (FLTM BI 106-01, Method B) chipping (Grade 0) 3.5.3 Salt Spray, min 240 h (FLTM BI 103-01) 3.5.4 Thermal Shock Resistance Must pass the following: Place the test panel in a circulating air oven at 155 C for 30 minutes. Remove and quench in cold water. Dry and immerse in

14、an alcohol-dry ice solution at -75 C for 10 minutes. Remove and inspect for signs of cracking, crazing, or loss of adhesion. Repeat above cycle 9 more times. At the end of the 10 cycles there must be no cracking, crazing, or signs of adhesion loss. 3.5.5 Thickness, min 30 micrometer (ASTM D 1186) 3.

15、5.6 Cure There must be no softening of coating or evidence of color rubbing off when a cloth dipped in MEK or acetone is rubbed over the surface of the resin. ENGINEERING MATERIAL SPECIFICATIONWSF-M70J10-APrinted copies are uncontrolled Copyright 2005, Ford Global Technologies, LLC Page 3 of 3 3.6 F

16、INISHED PARTS 3.6.1 Appearance The coating shall be continuous and free of blisters, cracks, bubbles, undercoating voids or mechanical damage. 3.6.2 Adhesion No flaking or (FLTM BI 106-01) chipping 3.6.3 Salt Spray, min 240 h (FLTM BI 103-01) 3.6.4 Thickness, min 30 micrometer (ASTM D 1186) 3.6.5 Cure There must be no softening of coating or evidence of color rubbing off when a cloth dipped in MEK or acetone is rubbed over the surface of the resin.