FORD WSD-M1A292-B-2002 STEEL - BOLT SELF LOCKING TO BE USED WITH FORD WSS-M99P1111-A 《钢制自锁螺栓 与标准FORD WSS-M99P1111-A一起使用 》.pdf

《FORD WSD-M1A292-B-2002 STEEL - BOLT SELF LOCKING TO BE USED WITH FORD WSS-M99P1111-A 《钢制自锁螺栓 与标准FORD WSS-M99P1111-A一起使用 》.pdf》由会员分享，可在线阅读，更多相关《FORD WSD-M1A292-B-2002 STEEL - BOLT SELF LOCKING TO BE USED WITH FORD WSS-M99P1111-A 《钢制自锁螺栓 与标准FORD WSS-M99P1111-A一起使用 》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Action Revisions 2002 09 30 Revised Updated and renumbered 1989 02 28 B/031521TC 3.3.4 renumbered to 3.4, STEEL added to title 1989 01 09 SM/ER1996TC Released, B.Edwards, EAO C.A.McKenney E.Staff Printed copies are uncontrol

2、led Page 1 of 2 Copyright 2002, Ford Global Technologies, Inc. STEEL - BOLT, SELF LOCKING WSD-M1A292-B 1. SCOPE The material defined by this specification is a heat treated steel with controlled surface hardness. 2. APPLICATION This specification was released to define the requirements of bolts with

3、 underhead self locking features. 3. REQUIREMENTS 3.1 STANDARD REQUIREMENTS FOR PRODUCTION MATERIALS Material suppliers and part producers must conform to the Companys Standard Requirements For Production Materials (WSS-M99P1111-A). 3.2 MATERIAL The choice of steel composition is at the manufacturer

4、s discretion and shall be suitable to meet the specified hardenability and other properties. The general quality of manufacture of the steel and wire product for bolt making shall conform to the relevant national standard for the country of sourcing. In the absence of a national standard or for refe

5、ree purposes, the steel shall conform to ISO 4954, section 1. Specific requirements for composition, mechanical properties and treatment condition of the wire shall conform to ISO 4954 or to the relevant national or industry standard. 3.3 HEAT TREATMENT All bolts shall be case hardened and tempered

6、to the required level as indicated. 3.3.1 CORE HARDNESS, HV30 265 - 325 The core hardness shall be determined at the mid-radial position on a cross section taken 1d from the threaded end. ENGINEERING MATERIAL SPECIFICATION WSD-M1A292-B Page 2 of 2 Copyright 2002, Ford Global Technologies, Inc. 3.3.2

7、 SURFACE HARDNESS, HV5 380 - 500 The surface hardness shall be determined at any suitable position on the bolt, but no more than 0.02 mm of surface shall be removed during preparation of a suitable surface for the hardness test. 3.3.3 CASE DEPTH, mm 0.1 - 0.25 Case depth shall be determined for refe

8、ree purposes by the microhardness traverse by the HV 0.3 method. The case depth is that depth with a hardness of 30 Vickers points above the actual core hardness. The surface hardness for this test shall be determined at 2.5 - 3 impression diagonals from the surface. 3.4 BREAKING FORCE, kN, min (ISO

9、 898/1 Clause 8.5 except 4 degree wedge angle) Size BREAKING FORCE M6 x 1 15.5 M8 x 1.25 28.0 M10 x 1.5 45.0 M12 x 1.75 65.0 Fracture shall occur in the threaded area except for bolts and screws with special heads which are weaker than the threaded section. The above requirements apply to head diame

10、ters up to 1.7d. For products with head diameters above 1.7d the head may be machined to 1.7d prior to test. For products too short for tensile testing a 4 degree head soundness test will apply in accordance with ISO 898/1 section 8.7 3.5 PROTECTIVE FINISH The protective finish shall be of a non emb

11、rittling type and shall be as released or as specified on the Engineering drawing for the part. 3.6 DEFECTS The general quality of thread, occurence and severity of thread defects shall conform to the requirements of the Worldwide Standard Parts Manual, WA990. 4. GENERAL INFORMATION The information

12、given below is provided for clarification and assistance in meeting the requirements of this specification. This material has a core hardness inline with ISO 898/1 property class 8.8. Products manufactured to this specification will give mechanical properties similar to grade 8.8 However, the high surface hardness will lead to a reduction in product ductility.