FORD M2C177-A (A)-2009 SPECIAL WAY LUBRICANT《特级导轨润滑油》.pdf

《FORD M2C177-A (A)-2009 SPECIAL WAY LUBRICANT《特级导轨润滑油》.pdf》由会员分享，可在线阅读，更多相关《FORD M2C177-A (A)-2009 SPECIAL WAY LUBRICANT《特级导轨润滑油》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 NON-PRODUCTION MATERIAL SPECIFICATION Material Name Specification Number Date Action Changes 2009 04 15 N-STATUS No Replacement Named L. Sinclair, FNA 1983 11 01 Page 1 of 2 SPECIAL WAY LUBRICANT M-2C177-A(A) NOT TO BE USED FOR NEW DESIGN 1. SCOPE: The material desired in this standard is a refined

2、 inhibited mineral oil adhesive type way lubricant with additives to retain lubricating qualities. 2. APPLICATION: This material is used as a way lubricant for transfer machines. 3. REQUIREMENTS: 3.1 SPECIFIC GRAVITY: (ASTM D 287) .914 - .918 3.2 VISCOSITY: (ASTM D 2422) 137 - 145 cSt 37.6 C 89 min

3、cSt 99.8 C 3.3 FLASH POINT: (ASTM D 92) +425F (218.3 C) min 3.4 FIRE POINT: +602F (316.7 C) min (ASTM D 97) 3.5 POUR POINT: -5F (-21 C) max (ASTM D 97) 3.6 ADHESIVENESS: The material shall be tacky to touch and have such adhesive properties to promote surface wear protection and minimize lubricant c

4、onsumption. 3.7 COMPATABILITY: All materials to this standard shall be compatible in all proportions with other materials approved under these “M“ numbers. Separation, precipitation or flocculation of solids or gels shall not be permitted. 3.8 INFRA RED SPECTRAL FINGERPRINT: Each material approved u

5、nder this Standard shall have its I.R. spectral characteristics established and maintained in the records of qualification for reference and product audit. NON-PRODUCTION MATERIAL SPECIFICATION M2C177-A (A) Page 2 of 2 3.9 SUPPLIERS RESPONSIBILITY: All materials supplied to this standard must be equ

6、ivalent in all characteristics to the material upon which approval was originally granted, and shall be suitable for the intended application. Changes in composition shall not be made without approval of Plant Engineering Office, Manufacturing Staff. 3.10 IDENTIFICATION: Materials supplied to this s

7、tandard shall be identified with the “M“ number printed on the side as well as the top of the containers in letters at least 2“ (50 mm) high in a contrasting color to that of the container. Container marking shall be in accordance with Manufacturing Standard ZF-10 and conform to all Federal, State,

8、and Local container contents labeling regula- tions which are in effect both in the area of shipment and use. 4. APPROVAL OF NEW SUPPLIERS: Materials submitted by new manufacturers to this standard must have Industrial Hygiene, Environmental Engineering, Laboratory and Shop Trial approvals. Supplier

9、s are required to complete and submit the Material Health and Safety Data Sheet (Form 1291) and the Environmental Data Sheet (Form 68-100) prior to Shop Trial. Recommendations for the addition of new manufacturers to the Manufacturing Approved Source List (ASL) must be made in writing to the respons

10、ible Manufacturing Staff Office by the appropriate divisional standards activity in accordance with Manufacturing Procedure IId1. 5. ENVIRONMENTAL CONTROL: Use of any material approved to this Standard must comply with the guidelines as established in the environmental review of the material, as the

11、y appear in the Materials and Toxicology (MATS) System. 6. HEALTH AND SAFETY: Use of any material approved to this standard must comply with the guidelines given under the Toxicological (TOX) review of the material as indicated in the MATS system. a. When contact with oil or grease is unavoidable, i

12、mpervious gloves should be worn as well as clean work clothes. b. When skin exposure cannot be avoided, removal of grease from the skin should be as prompt as possible. A mild soap or skin cleanser and water should be used to remove oil or grease. Industrial solvents should not be used to clean the skin.