FORD FLTM BV 130-1-2000 SEALER FUME TEST - EFFECT OF SEALER FUMES ON PAINT ADHESION.pdf
《FORD FLTM BV 130-1-2000 SEALER FUME TEST - EFFECT OF SEALER FUMES ON PAINT ADHESION.pdf》由会员分享,可在线阅读,更多相关《FORD FLTM BV 130-1-2000 SEALER FUME TEST - EFFECT OF SEALER FUMES ON PAINT ADHESION.pdf(4页珍藏版)》请在麦多课文档分享上搜索。
1、 FORD LABORATORY TEST METHOD BV 130-01 Date Action Revisions 2000 12 11 Revised Editorial no technical change A. Cockman 1998 09 01 Printed copies are uncontrolled Page 1 of 4 Copyright 2000, Ford Global Technologies, Inc. SEALER FUME TEST - EFFECT OF SEALER FUMES ON PAINT ADHESION Application This
2、procedure is used to determine the effect of fumes from sealers during primer oven bake and topcoat repaint on the adhesion properties of subsequent paint applications. Apparatus Required Mechanical Convection Oven The oven must be capable of maintaining a temperature of 165 +/- 2 C or as specified
3、by the applicable Engineering Material Specification. Materials Required Test Panels Electrocoated G60 Galvanized or CRLC Steel panels: 300 x 100 mm. Prepared in accordance to FLTM BI 120-01 or as specified by the responsible Engineering activity. Paint Can 1/2 liter with opening such that Test Pane
4、l width can completely cover opening. Aluminum Foil Glass Reinforced Adhesi ve Tape 3M Scotch, Pressure Sensitive Filament, No. 898, 25 mm wide. Use only No. 898 tape manufactured in the U.S.A. Store in the original package in a dry, dark location. NOTE: Use adhesion tape before its expiration date.
5、 Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. FORD LABORATORY TEST
6、 METHOD BV130-01 Page 2 of 4 Copyright 2000, Ford Global Technologies, Inc. Procedure A - Sealer Fumes During Primer Bake 1. Spread out 10 - 12 g of the specified sealer on the inside bottom of 1/2 liter can so that entire bottom of can is covered with sealer. 2. Cover can with aluminum foil. 3. Pre
7、-gel sealer in can at 121 C for seven minutes. Allow to cool for 20 minutes at 23 C. 4. Apply primer as specified by the responsible Engineering activity to electrocoated test panel. Remove aluminum foil from can and place primed panel (wet side down) over can opening leaving a 13 mm gap between top
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- FORDFLTMBV13012000SEALERFUMETESTEFFECTOFSEALERFUMESONPAINTADHESIONPDF

链接地址:http://www.mydoc123.com/p-747646.html