FORD FLTM BN 108-14-2015 RESISTANCE TO TOPCOAT WEAR OF LEATHER.pdf

《FORD FLTM BN 108-14-2015 RESISTANCE TO TOPCOAT WEAR OF LEATHER.pdf》由会员分享，可在线阅读，更多相关《FORD FLTM BN 108-14-2015 RESISTANCE TO TOPCOAT WEAR OF LEATHER.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 FORD LABORATORY TEST METHOD BN 108-14 Date Action Revisions Rev 3 2015 01 30 Editorial See Summary of Revisions D. Murtonen, NA 2011 01 12 Revised Updated sources (addresses and ph nrs); update evaluation; updated figure 1 M. Dumitrescu, NA; J. Williams, EU 1998 10 14 Controlled document at www.MAT

2、S Copyright 2014, Ford Global Technologies, LLC Page 1 of 4 RESISTANCE TO TOPCOAT WEAR OF LEATHER Application This test method determines the abrasion resistance of high wear leather and genuine leather. Required Test Equipment Pilling Tester* - Model no. CS-53 Specimen Holder and Weight* As specifi

3、ed by the relevant engineering document *Source: Standard Scientific Supply Company P.O. Box 484 Bethlehem, PA 18018-5208 U.S.A. Phone: (610) 838-7500 Fax: (610) 838-6214 Abradant The abradant shall be no. 8 cotton duck cloth, style 474 and shall be rigidly mounted on the pilling board. Source: Test

4、 Fabrics, Inc. PO Box 3026 415 Delaware Ave West Pittston, PA 18643 USA Phone: (570) 603 0432 Fax: (570) 603 0433 Email: Sewing Machine Capable of producing a lock stitched deck seam and French seam as described in Step 2 of the Procedure. Sewing Needle Type 135 x 17, size 2 Source: M.J. Foley Com

5、pany 52026 Sierra Drive New Baltimore, Michigan 48047 Phone (586) 948-6070 Fax (586) 948-6081 FORD LABORATORY TEST METHOD BN 108-14 Copyright 2015, Ford Global Technologies, LLC Page 2 of 4 Sewing Thread Top and bottom threads shall conform to WSS-M8P25-A/N90, or engineering approved equivalent, unl

6、ess otherwise specified by the responsible Materials Engineering Activity. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5% relative humidity for not less than 24 h prior to testing and tested u

7、nder the same conditions unless otherwise specified. Procedure 1. Cut two leather test specimens each 90 x 130 mm in size. 2. Sew the test specimens with a french seam parallel to the 90 mm side, (see Figure 1). Sew the specimens with a lock stitch, employing 5 - 6 stitches per 25 mm. The top and bo

8、ttom sewing threads shall meet the requirements of WSS-M8P25-A/N90, or engineering approved equivalent unless otherwise specified by the responsible Materials Engineering Activity. 3. Wrap the pilling board with no. 8 cotton duck cloth. The abradant shall be rigidly mounted on the pilling board with

9、 staples on the side. A new piece of cotton duck cloth should be used on every sample. 4. Wrap the test specimen around the specimen holder with the deck seam parallel to the center of the holder. To avoid formation of folds or wrinkles and/or slipping of the specimen during the test, the specimen s

10、hall be held in the specimen holder with double-sided adhesive tape. 5. Place the weight in position. Use the test weight and time as specified in the relevant engineering document. The pilling weight shall be balanced so that the specimen holder with the test specimen can rock back and forth during

11、 the test. Evaluation Assess the results by comparing with the currently approved master sample. The material shall be judged a failure: - if the test exhibited loss of adhesion, such as lifting or delamination of the top coat from the russet (top skin). - if the top coat exhibited wear through to t

12、he russet, when it is examined with a 6 x magnified glass. Chemicals, materials, parts, and equipment referenced in this document must be used and handled properly. Each party is responsible for determining proper use and handling in its facilities. FORD LABORATORY TEST METHOD BN 108-14 Copyright 20

13、15, Ford Global Technologies, LLC Page 3 of 4 Figure 1 8 mm 10 mm 4 mm FORD LABORATORY TEST METHOD BN 108-14 Copyright 2015, Ford Global Technologies, LLC Page 4 of 4 SUMMARY OF REVISIONS 2015 01 30 Editorial Changed title from Resistance to Pilling to Resistance to Top Coat. Changed WSD-M15H51-D and WSS-M15H51-E to WSS-M8P25-A/N90.