FORD ESF-M4D405-C2-2010 POLYETHYLENE TEREPHTHALATE (PET) 30 % GLASS REINFORCED MOLDING COMPOUND SELF-EXTINGUISHING (SE) TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 30%玻璃纤.pdf

《FORD ESF-M4D405-C2-2010 POLYETHYLENE TEREPHTHALATE (PET) 30 % GLASS REINFORCED MOLDING COMPOUND SELF-EXTINGUISHING (SE) TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 30%玻璃纤.pdf》由会员分享，可在线阅读，更多相关《FORD ESF-M4D405-C2-2010 POLYETHYLENE TEREPHTHALATE (PET) 30 % GLASS REINFORCED MOLDING COMPOUND SELF-EXTINGUISHING (SE) TO BE USED WITH FORD WSS-M99P1111-A 《聚乙烯对苯二甲酸酯(PET) 30%玻璃纤.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATION Material Name Specification Number Date Release No. Released 2010 11 16 C2 N-STATUS C2 no replacement named. A. Pan, APA 1992 01 24 Revised 3.1.1 & 3.2.9 for 4D405-C1 L.P. Rumao 1980 05 15 CF4K-RD576983-6 Released ESF-M4D405-C J.B. Huebner WP 3948-a Page 1 of 5 PO

2、LYETHYLENE TEREPHTHALATE (PET), ESF-M4D405-C1 30 % GLASS REINFORCED MOLDING COMPOUND POLYETHYLENE TEREPHTHALATE (PET, ESF-M4D405-C2 30 % GLASS REINFORCED MOLDING COMPOUND, SELF-EXTINGUISHING (SE) NOT TO BE USED FOR NEW DESIGN 1. SCOPE The materials defined by these specifications are glass reinforce

3、d thermoplastic polyester resins based on polyethylene terephthalate (PET). 2. APPLICATION These specifications were released originally for materials used to mold frames for ignition control modules. ESF-M4D405-C1 replaces and is same as ESF-M4D405-C. 3. REQUIREMENTS 3.1 MOLDING COMPOUND C1 C2 3.1.

4、1 Melting Point, C, min 235 240 (ASTM D 789) 3.1.2 Glass Fiber Content, +/- 2 % by weight 30 31 (ASTM D 2584, 1 h at 666 C or TGA) 3.1.3 Melt Flow Rate, g/10 minutes, max 11.0 8.0 (ASTM D 1238, 280 +/- 0.2 C, 2.16 kg) Dry sample for 1 h at 175 C in circulating air oven and maintain at this temperatu

5、re until immediately before testing. Quickly charge indexer. Charging time not to exceed 1 minute. 3.2 MOLDED TEST SPECIMEN 3.2.1 Preparation of Test Specimens All test specimens shall be injunction molded in accordance with ASTM D 1897. The values of this specification are based on natural color, i

6、njection molded specimens unless otherwise specified on engineering drawing. ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-C1/C2 WP 3948-b Page 2 of 5 3.2.2 Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C an

7、d 50 +/- 5 % relative humidity for not less than 24 h prior to testing and tested under the same conditions unless otherwise specified. C1 C2 3.2.3 Specific Gravity 1.54 - 1.58 1.64 - 1.70 (ASTM D 792) 3.2.4 Tensile Strength, MPa, min 145 124 (ASTM D 638) 3.2.5 Flexural Modulus, GPa, min 7.6 7.6 (AS

8、TM D 790) 3.2.6 Flexural Strength, MPa, min 207 192 (ASTM D 790) 3.2.7 Compressive Strength, MPa, min 165 124 (ASTM D 695, in machine direction) 3.2.8 Impact Strength, Izod, J/m, min 80 69 (ASTM D 256, notched) 3.2.9 Heat Deflection Temperature, C, min 215 210 (ASTM D 648, at 1.80 MPa) 3.2.10 Dielec

9、tric Strength, kV/mm, min (ASTM D 149, short time) . Natural 18.5 16.8 . Black 13.8 - 3.2.11 Flammability, ESF-M4D405-C2 Only Burn Rate, max SE/0 (FLTM BN 24-2, without the lot sampling plan) In addition, the test specimen shall not exhibit any flashing or sudden flaming on either surface in excess

10、of the above maximum value. 3.3 MOLDED PARTS 3.3.1 Color As specified on engineering drawing. ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-C1/C2 WP 3948-b Page 3 of 5 3.3.2 Appearance Shall be uniform in density, texture and finish, free of visible porosity and voids, warpage, heat scorch, checks,

11、cracks, chipped edges and uneven surfaces. Shall also be free of other contamination. C1 C2 3.3.3 Specific Gravity 1.54 - 1.58 1.64 - 1.70 (ASTM D 792) 3.3.4 Glass Fiber Content, % by weight 30 +/- 2 31 +/- 2 3.3.5 Flow Rate, g/10 minutes, max 30.0 30.0 (ASTM D 1238, 280 +/- 0.2 C, 2.16 kg) 3.3.6 Ad

12、ditional Requirements Specific requirements for material and/or manufactured parts shall be specified on the Engineering drawing, Engineering parts specification and/or performance specifications. All critical areas with respect to these properties shall be clearly designated on the engineering draw

13、ing. 3.4 INFRARED SPECTROPHOTOMETRY AND/OR THERMAL ANALYSIS Ford Motor Company, at its option, may conduct infrared and/or thermal analysis of material/parts supplied to this specification. The spectra established for initial approval shall constitute the reference standard and shall be kept on file

14、 at the designated material laboratory. All samples shall produce spectra that correspond to the reference standard when tested under the same conditions as those specified on the master spectrum. 3.5 STATISTICAL PROCESS Suppliers must conform to the requirements of Ford Quality System Standard Q-10

15、1. A mutually acceptable Control Plan as described therein is required for material/source approval. Appropriate statistical tools must be used to analyze process/product data so that variation in the final product is continuously reduced. 3.6 SUPPLIERS RESPONSIBILITY All materials supplied to this

16、specification must be equivalent in all characteristics to the material upon which approval was originally granted. ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-C1/C2 WP 3948-b Page 4 of 5 Prior to making any change in the properties, composition, construction, color, processing or labeling of the

17、material originally approved under this specification, whether or not such changes affect the materials ability to meet the specification requirements, the Supplier shall notify Purchasing, Toxicology and the affected Materials Engineering activity of the proposed changes and obtain the written appr

18、oval of the Materials Engineering activity. Test data, test samples and a new code identification are to be submitted with the request. Substance restrictions imposed by law, regulations or Ford, apply to the materials addressed by this document. The restrictions are defined in Engineering Materials

19、 Specification WSS-M99P9999-A1. 4. APPROVAL OF MATERIALS Materials defined by this specification must have prior approval by the responsible Materials Engineering activity. Suppliers desiring approval of their materials shall first obtain an expression of interest from the affected Purchasing, Desig

20、n and Materials Engineering activity. Upon request, the Supplier shall submit to the affected Materials Engineering activity a completed copy of their laboratory test reports, signed by a qualified and authorized representative of the test facility, demonstrating full compliance with all the require

21、ments of this specification (test results, not nominal values), the material designation and code number, and test specimens for Ford evaluation. Fords engineering approval of a material will be based on its performance to this specification and on an assessment of suitability for intended processes

22、 and/or applications. Upon approval, the material will be added to the Engineering Material Approved Source List. 5. GENERAL INFORMATION The information below is provided for clarification and assistance in meeting the requirements of this specification. 5.1 FLAMMABILITY (C1 only) 10 mm/minute (FLTM BN 24-2) 5.2 ELONGATION (C1 only) 2.7 % (ASTM D 638) 5.3 IMPACT STRENGTH, IZOD (C1 only) 907 J/m (ASTM D 256, unnotched) ENGINEERING MATERIAL SPECIFICATION ESF-M4D405-C1/C2 WP 3948-b Page 5 of 5 5.4 RECYCLING CODE ESF-M4D405-C1 SAE PET-GF30 or PET-GF30PET-GF31 OPTIONAL