FORD ESB-M17H155-A-2006 PADDING COMPOSITE - ARAMID GLASS POLYESTER FIBER TO BE USED WITH WSS-M99P1111-A 《芳族聚酰胺 玻璃 聚酯纤维复合材料衬垫 与标准FORD WSSS-M99P1111-A一起使用 使用标准WSS-M99P32-B》.pdf

《FORD ESB-M17H155-A-2006 PADDING COMPOSITE - ARAMID GLASS POLYESTER FIBER TO BE USED WITH WSS-M99P1111-A 《芳族聚酰胺 玻璃 聚酯纤维复合材料衬垫 与标准FORD WSSS-M99P1111-A一起使用 使用标准WSS-M99P32-B》.pdf》由会员分享，可在线阅读，更多相关《FORD ESB-M17H155-A-2006 PADDING COMPOSITE - ARAMID GLASS POLYESTER FIBER TO BE USED WITH WSS-M99P1111-A 《芳族聚酰胺 玻璃 聚酯纤维复合材料衬垫 与标准FORD WSSS-M99P1111-A一起使用 使用标准WSS-M99P32-B》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 ENGINEERING MATERIAL SPECIFICATIONDate Action Revisions 2006 05 04 N-STATUS Replaced by WSS-M99P32-B; Ins 3.0; Del 3.1, 3.2, 3.15 19 - 50 mm staple length Glass Fibers 45 +/- 5% 5.5 - 6.5 mm fiber diameter Polyester Fibers 48 +/- 5% 15 - 25 denier; 50 - 75 mm staple length (For specified thicknesse

2、s greater than 15 mm, only the polyester fiber thickness should be increased) 3.5 WEIGHT 1.0 +/- 0.10 kg/m or as otherwise specified on engineering drawing ENGINEERING MATERIAL SPECIFICATION ESB-M17H155-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 2 of 3 3.6 T

3、HICKNESS 15.0 mm +/- 15% or as otherwise specified on the engineering drawing. 3.7 BREAKING STRENGTH, min (ASTM D 1682, Test No. 2 C - E, avg. of 5) Strongest Direction 20.0 N Cross Direction 10.0 N 3.8 COMPRESSION & RECOVERY Compression, max 15% Recovery, min 50% Test Method: Cut five, 305 x 305 mm

4、 samples. Apply a 305 x 305 mm platen weighing 0.23 kg to the five plied samples. Measure the height of the pile, at the center of the vertical sides. (The average of these readings is the initial thickness of the pile (T). Apply a 2.3 kg load to the center of the pile and measure again for average

5、thickness of the pile with load (T2). % Compression = T1- T2X 100 - T1Remove the load and allow pile (with platen to recover thickness for 30 min. Measure again for average thickness of the pile (T3). % Recovery = T3- T2X 100 - T1- T23.9 THERMAL CONDUCTIVITY, max, Initial Approval Only (ASTM C 518,

6、25 mm thick sample) Mean temperature 24 C 0.039 Wm-1 -1 93 C 0.046 Wm-1 -1 3.10 DYNAMIC FLEX FATIGUE, For Initial Approval Only (FLTM BO 12-4, Method “B“, 150 cycles, 13.6 kg load) No separation or destruction by breakage of the fibers along the rubbing track of the simulated heel both before and af

7、ter heat aging. Test Method: Prepare two, 250 x 250 mm samples of the insulator batt. Heat age one sample for 24 h at 232 C and condition at 23 +/- 2 C for 4 h. Staple both samples adjacent to each other on a 250 x 500 mm medium to lightweight pile carpet (ESB-M3H20 or ESB-M3H30 type). Conduct the t

8、est as indicated above, making sure the simulated heel passes over both paddings in the same stroke. ENGINEERING MATERIAL SPECIFICATION ESB-M17H155-A Printed copies are uncontrolled Copyright 2006, Ford Global Technologies, LLC Page 3 of 3 3.11 WEIGHT LOSS, max 10% Test Method: Cut a sample of mater

9、ial weighing approximately 4 to 5 grams. Dry the sample in a mechanically convected oven for 16 hours at 121 C. Remove from oven and immediately determine the weight to the nearest 0.01 of a gram using an analytical balance (W1). Place sample in a muffle furnace for 16 hours at 220 C. (Place sample

10、on aluminum foil in furnace to prevent dirt pick-up). Remove from furnace and immediately reweight to the nearest 0.01 of a gram (W2). Calculate the % weight loss. % Weight Loss = W1- W2X 100 - W13.12 HEAT TRANSFER, max, Initial Approval Only 60 C on carpet surface (FLTM BN 8-11) Procedure “C“, exce

11、pt use a constant steel plate temperature of 175 C. Use 13 mm thick composite batt. 3.13 INTERNAL STRENGTH, min 0.12 N/cm (Avg. of 5) Test Method: Cut test specimens 250 mm x 50 mm and separate at the glass center and glass/polyester interface across the 50 mm width. Mount the sample on an Instron o

12、r equivalent tester and pull at a rate of 305 mm/min for at least 150 mm of the specimen length. Results of each individual test specimen shall be determined as a mean average of the high and low values indicated on the chart. 3.14 FLAMMABILITY In order to comply with Federal Motor Vehicle Safety Standard No. 302, the materials, portions of components, and composites shall not burn, or transmit a flame across its surface, at a rate of more than 100 mm per min. To demonstrate compliance, the sample size and method of testing shall be in accordance with FLTM BN 024-02.