ETSI TS 119 144-1-2016 Electronic Signatures and Infrastructures (ESI) PAdES digital signatures - Testing Conformance and Interoperability Part 1 Overview (V1 1 1)《电子签名和基础设施(ESI) P.pdf

《ETSI TS 119 144-1-2016 Electronic Signatures and Infrastructures (ESI) PAdES digital signatures - Testing Conformance and Interoperability Part 1 Overview (V1 1 1)《电子签名和基础设施(ESI) P.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 119 144-1-2016 Electronic Signatures and Infrastructures (ESI) PAdES digital signatures - Testing Conformance and Interoperability Part 1 Overview (V1 1 1)《电子签名和基础设施(ESI) P.pdf（8页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TR 119 144-1 V1.1.1 (2016-06) Electronic Signatures and Infrastructures (ESI); PAdES digital signatures - Testing Conformance and Interoperability; Part 1: Overview TECHNICAL REPORT ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)2 Reference DTR/ESI-0019144-1 Keywords conformance, e-commerce, electroni

2、c signature, PAdES, profile, security, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice

3、The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorizatio

4、n of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be awar

5、e that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx If you find errors in the present document, please send your comment to one of the following ser

6、vices: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version s

7、hall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2016. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered

8、for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)3 Contents Intellectual P

9、roperty Rights 4g3Foreword . 4g3Modal verbs terminology 4g3Introduction 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 5g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 6g34 Testing Conformance and Interoperability . 6g34.1 Part 2:

10、 Test suites for testing interoperability of PAdES baseline signatures . 6g34.2 Part 3: Test suites for testing interoperability of additional PAdES signatures profiles . 6g34.3 Part 4: Testing Conformance of PAdES baseline signatures 7g34.4 Part 5: Testing Conformance of additional PAdES signatures

11、 . 7g3History 8g3ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)4 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, a

12、nd can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to th

13、e ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. For

14、eword This Technical Report (TR) has been produced by ETSI Technical Committee Electronic Signatures and Infrastructures (ESI). The present document is part 1 of a multi-part deliverable covering PAdES digital signatures - Testing Conformance and Interoperability, as identified below: ETSI TR 119 14

15、4-1: “Overview“; ETSI TS 119 144-2: “Test suites for testing interoperability of PAdES baseline signatures“; ETSI TS 119 144-3: “Test suites for testing interoperability of additional PAdES signatures“; ETSI TS 119 144-4: “Testing Conformance of PAdES baseline signatures“; ETSI TS 119 144-5: “Testin

16、g Conformance of additional PAdES signatures“. Modal verbs terminology In the present document “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions)

17、. “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Introduction The multi-part deliverable defines test suites for testing interoperability and conformance of PAdES signatures. The set of Technical Specifications consist of four documents. The test suit

18、es for testing interoperability of PAdES baseline signatures (Part 2 i.6) and the specifications required for building software tools for testing technical conformance of PAdES baseline signatures (Part 4 i.4) are defined against ETSI EN 319 142-1 i.1. The test suites for testing interoperability of

19、 additional PAdES signatures (Part 3 i.7) and the specifications required for building software tools for testing technical conformance of additional PAdES signatures (Part 5 i.8) are defined against ETSI EN 319 142-2 i.2. ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)5 1 Scope The present document provide

20、s an overview of the set of test suites for testing interoperability and conformance of PAdES signatures. The present document: a) provides a general description of the set of test suites for testing interoperability and conformance of PAdES signatures; and b) lists the features of every test suite

21、for testing interoperability and conformance of PAdES signatures. The present document is for information only. Normative requirements of each test suite are in other parts of this multi-part deliverable. 2 References 2.1 Normative references As informative publications shall not contain normative r

22、eferences this clause shall remain empty. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specific references, the latest version of

23、 the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the application of the present document but

24、they assist the user with regard to a particular subject area. i.1 ETSI EN 319 142-1: “Electronic Signatures and Infrastructures (ESI); PAdES digital signatures; Part 1: Building blocks and PAdES baseline signatures“. i.2 ETSI EN 319 142-2: “Electronic Signatures and Infrastructures (ESI); PAdES dig

25、ital signatures; Part 2: Additional PAdES signatures profiles“. i.3 ETSI TR 119 001: “Electronic Signatures and Infrastructures (ESI); The framework for standardization of signatures; Definitions and abbreviations“. i.4 ETSI TS 119 144-4: “Electronic Signatures and Infrastructures (ESI); PAdES digit

26、al signatures - Testing Conformance and Interoperability; Part 4: Testing Conformance of PAdES baseline signatures“. i.5 ETSI EN 319 102-1: “Electronic Signatures and Infrastructures (ESI); Procedures for Creation and Validation of AdES Digital Signatures; Part 1: Creation and Validation“. i.6 ETSI

27、TS 119 144-2: “Electronic Signatures and Infrastructures (ESI); PAdES digital signatures - Testing Conformance and Interoperability; Part 2: Test suites for testing interoperability of PAdES baseline signatures“. i.7 ETSI TS 119 144-3: “Electronic Signatures and Infrastructures (ESI); PAdES digital

28、signatures - Testing Conformance and Interoperability; Part 3: Test suites for testing interoperability of additional PAdES signatures“. i.8 ETSI TS 119 144-5: “Electronic Signatures and Infrastructures (ESI); PAdES digital signatures - Testing Conformance and Interoperability; Part 5: Testing Confo

29、rmance of additional PAdES signatures“. ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)6 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and definitions given in ETSI TR 119 001 i.3 and the following apply: negative test case: test case for a signature who

30、se validation according to ETSI EN 319 102-1 i.5 would not result in TOTAL-PASSED 3.2 Abbreviations For the purposes of the present document, the abbreviations given in ETSI TR 119 001 i.3 apply. 4 Testing Conformance and Interoperability 4.1 Part 2: Test suites for testing interoperability of PAdES

31、 baseline signatures ETSI TS 119 144-2 i.6 specifies the test suites for testing interoperability of PAdES baseline signatures against ETSI EN 319 142-1 i.1. ETSI EN 319 142-1 i.1 defines four different levels of PAdES baseline signatures. The test suites will be defined with different layers reflec

32、ting the levels of PAdES baseline signatures specified in ETSI EN 319 142-1 i.1. Testing PAdES signatures interoperability between applications claiming B-B level conformance. Testing PAdES signatures interoperability between applications claiming B-T level conformance. Testing PAdES signatures inte

33、roperability between applications claiming B-LT level conformance. Testing PAdES signatures interoperability between applications claiming B-LTA level conformance. Testing augmentation of PAdES signatures from B-T level to B-LTA level. Testing negative PAdES baseline signatures: - PAdES-B-B signatur

34、es test cases; - PAdES-B-T signatures test cases; - PAdES-B-LTA signatures test cases. 4.2 Part 3: Test suites for testing interoperability of additional PAdES signatures profiles ETSI TS 119 144-3 i.7 specifies the test suites for testing interoperability of additional PAdES signatures against ETSI

35、 EN 319 142-2 i.2. ETSI EN 319 142-2 i.2 defines different signature forms. The test suites are defined with different layers reflecting the forms of additional PAdES signatures profiles specified in ETSI EN 319 142-2 i.2. ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)7 Testing PAdES signatures: PAdES-E-BE

36、S signatures test cases; PAdES-E-EPES signatures test cases; PAdES-E-LTV signatures test cases; XAdES signatures of XML documents embedded in PDF containers test cases; XAdES signatures on XFA forms test cases. Testing negative additional PAdES signatures: PAdES-E-BES test cases; PAdES-E-EPES test c

37、ases; PAdES-E-LTV signatures test cases. 4.3 Part 4: Testing Conformance of PAdES baseline signatures ETSI TS 119 144-4 i.4 defines the requirements for building software tools for testing technical conformity of PAdES baseline signatures against ETSI EN 319 142-1 i.1. ETSI EN 319 142-1 i.1 defines

38、requirements for building blocks and PAdES baseline signatures. For the purpose of identifying the whole set of test assertions required for testing conformance against PAdES baseline signatures as specified in ETSI EN 319 142-1 i.1, ETSI TS 119 144-4 i.4 classifies the whole set of requirements spe

39、cified in ETSI EN 319 142-1 i.1 in two groups as follows: 1) Requirements specific to PAdES baseline signatures. 2) Requirements common to both PAdES baseline signatures as specified in ETSI EN 319 142-1 i.1 and additional PAdES signatures profiles as specified in ETSI EN 319 142-2 i.2. 4.4 Part 5:

40、Testing Conformance of additional PAdES signatures ETSI TS 119 144-5 i.8 defines the requirements for building software tools for testing technical conformance of additional PAdES signatures against ETSI EN 319 142-2 i.2. ETSI EN 319 142-1 i.1 defines requirements for building blocks and PAdES basel

41、ine signatures. For the purpose of identifying the whole set of test assertions required for testing conformance against additional PAdES signatures profiles as specified in ETSI EN 319 142-2 i.2, ETSI TS 119 144-5 i.8 classifies the whole set of requirements specified in ETSI EN 319 142-1 i.1 and i

42、n ETSI EN 319 142-2 i.2 in two groups as follows: 1) Requirements common to both PAdES baseline signatures as specified in ETSI EN 319 142-1 i.1 and additional PAdES signatures profiles as specified in ETSI EN 319 142-2 i.2 (these requirements are incorporated by references to ETSI TS 119 144-4 i.4). 2) Requirements specific to additional PAdES signatures profiles. ETSI ETSI TR 119 144-1 V1.1.1 (2016-06)8 History Document history V1.1.1 June 2016 Publication