ETSI TS 102 709-1-2014 Core Network and Interoperability Testing (INT) Interworking between the 3GPP Cs domain with BICC or ISUP as signalling protocol and external SIP-I networks _1.pdf

《ETSI TS 102 709-1-2014 Core Network and Interoperability Testing (INT) Interworking between the 3GPP Cs domain with BICC or ISUP as signalling protocol and external SIP-I networks _1.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 709-1-2014 Core Network and Interoperability Testing (INT) Interworking between the 3GPP Cs domain with BICC or ISUP as signalling protocol and external SIP-I networks _1.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 709-1 V3.2.1 (2014-10) Core Network and Interoperability Testing (INT); Interworking between the 3GPP Cs domain with BICC or ISUP as signalling protocol and external SIP-I networks; (3GPP Release 8); Part 1: Protocol Implementation Conformance Statement (PICS) TECHNICAL SPECIFICATION ET

2、SI ETSI TS 102 709-1 V3.2.1 (2014-10)2Reference RTS/INT-00116-1 Keywords BICC, interworking, ISUP, PICS, SIP-I, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Association but non lucrati

3、f enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shal

4、l not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI S

5、ecretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please

6、 send your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of

7、ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 2014. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI lo

8、go are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks registered and owned by the GSM Association. ETSI ETSI TS 102 709-1 V3.

9、2.1 (2014-10)3Contents Intellectual Property Rights 4g3Foreword . 4g3Modal verbs terminology 4g31 Scope 5g32 References 5g32.1 Normative references . 5g32.2 Informative references 6g33 Definitions and abbreviations . 6g33.1 Definitions 6g33.2 Abbreviations . 7g34 Scenarios 8g34.1 SIP Profile A and B

10、 for interworking between SIP and BICC/ISUP . 8g34.2 SIP Profile C for Interworking Between SIP with MIME Encoding of ISUP and BICC/ISUP . 9g35 PICS proforma 11g35.1 Instructions for completing the PICS proforma 11g35.1.1 Other information . 11g35.1.2 Purposes and structure 11g35.1.3 Conventions 11g

11、35.2 Identification of the implementation 13g35.2.1 Date of the statement 13g35.2.2 Implementation Under Test (IUT) identification 13g35.2.3 System Under Test (SUT) identification 13g35.2.4 Product supplier 13g35.2.5 Client 13g35.2.6 PICS contact person 13g35.3 PICS proforma tables . 14g35.3.1 Globa

12、l statement of conformance . 14g35.3.2 Roles . 14g35.3.3 Connection types 14g35.3.4 Forward address signalling . 15g35.3.5 Role independent capabilities . 15g35.3.6 Supplementary Services Major Capabilities . 16g35.3.7 Timers . 19g35.4 Additional information for PICS 19g3Annex A (informative): Bibli

13、ography . 20g3History 22g3ETSI ETSI TS 102 709-1 V3.2.1 (2014-10)4Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-me

14、mbers, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/ipr.etsi.org). Pursuant

15、 to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present documen

16、t. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Core Network and Interoperability Testing (INT). The present document is part 1 of a multi-part deliverable covering the Interworking between the 3GPP Cs domain with BICC or ISUP as signalling protocol and ex

17、ternal SIP-I networks , as identified below: Part 1: “Protocol Implementation Conformance Statement (PICS)“; Part 2: “Test Suite Structure and Test Purposes (TSS Universal Mobile Telecommunications System (UMTS); LTE; Interworking between the 3GPP Cs domain with BICC or ISUP as signalling protocol a

18、nd external SIP-I networks (3GPP TS 29.164 version 8.0.0 Release 8)“. 2.2 Informative references The following referenced documents are not necessary for the application of the present document but they assist the user with regard to a particular subject area. Not applicable. 3 Definitions and abbre

19、viations 3.1 Definitions For the purposes of the present document, the following terms and definitions apply: Abstract Test Case (ATC): complete and independent specification of the actions required to achieve a specific test purpose, defined at the level of abstraction of a particular Abstract Test

20、 Method, starting in a stable testing state and ending in a stable testing state Abstract Test Method (ATM): description of how an SUT is to be tested, given at an appropriate level of abstraction to make the description independent of any particular realization of a Means of Testing, but with enoug

21、h detail to enable abstract test cases to be specified for this method Abstract Test Suite (ATS): test suite composed of abstract test cases Implementation Under Test (IUT): implementation of one or more OSI protocols in an adjacent user/provider relationship, being part of a real open system which

22、is to be studied by testing Means Of Testing (MOT): combination of equipment and procedures that can perform the derivation, selection, parameterization and execution of test cases, in conformance with a reference standardized ATS, and can produce a conformance log PICS proforma: document, in the fo

23、rm of a questionnaire, which when completed for an implementation or system becomes the PICS PIXIT proforma: document, in the form of a questionnaire, which when completed for the SUT becomes the PIXIT Point of Control and Observation (PCO): point within a testing environment where the occurrence of

24、 test events is to be controlled and observed, as defined in an Abstract Test Method pre-test condition: setting or state in the SUT which cannot be achieved by providing stimulus from the test environment Protocol Implementation Conformance Statement (PICS): statement made by the supplier of a prot

25、ocol claimed to conform to a given specification, stating which capabilities have been implemented ETSI ETSI TS 102 709-1 V3.2.1 (2014-10)7Protocol Implementation eXtra Information for Testing (PIXIT): statement made by a supplier or implementor of an SUT (protocol) which contains or references all

26、of the information related to the SUT and its testing environment, which will enable the test laboratory to run an appropriate test suite against the SUT SIP number: number conforming to the numbering and structure specified in Recommendation ITU-T E.164 11 System Under Test (SUT): real open system

27、in which the SUT resides user: access protocol entity at the user side of the user-network interface where a T reference point or coincident S and T reference point applies 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: ACM Address Complete Message ACR

28、 Anonymous Call Rejection supplementary service AMR Adaptive Multi Rate (codec) ATC Abstract Test Case ATM Abstract Test Method ATS Abstract Test Suite BICC Bearer Independent Call Control protocol CCBS Call Completion to Busy Subscriber supplementary service CCNR Call Completion on No Reply supplem

29、entary service CD Call Deflection supplementary service CDIV Call DIVersion supplementary service CFB Call Forwarding on Busy supplementary service CFNR Call Forwarding on No Reply supplementary service CFU Call Forwarding Unconditional supplementary service CLI Calling Line Identity CLIP Calling Li

30、ne Identification Presentation supplementary service CLIR Calling Line Identification Restriction supplementary service COL Connected Line Identity COLP Connected Line Identification Presentation supplementary service COLR Connected Line identification Restriction supplementary service CONF CONFeren

31、ce Call supplementary service CUG Closed User Group CW Call Waiting supplementary service ECT Explicit Call Transfer supplementary service FRJ Facility ReJect message IAM Initial Address MessageICS Implementation Conformance Statement IP Internet Protocol IRS Identification Response message ISDN Int

32、egrated Services Digital Network ISUP ISDN User Part IUT Implementation Under Test IWU InterWorking Unit LOP LOop Prevention message MCID Malicious Communication IDentification supplementary service MOT Means Of Testing PCM Pulse Code Modulation PCO Point of Control and Observation PICS Protocol Imp

33、lementation Conformance Statement PIXIT Protocol Implementation eXtra Information for Testing REL RELease message SDP Session Description Protocol SIP Session Initiation Protocol SUB SUBaddress supplementary service SUT System Under Test TMR Transmission Medium Requirement parameter TP Test Purpose

34、ETSI ETSI TS 102 709-1 V3.2.1 (2014-10)8TSS Test Suite Structure TSS identification of the implementation; identification of the reference protocol specification; PICS proforma tables (containing the global statement of conformance). 5.1.3 Conventions The PICS proforma is composed of information in

35、tabular form in accordance with the guidelines presented in ISO/IEC 9646-7 9. Item column It contains a number that identifies the item in the table. ETSI ETSI TS 102 709-1 V3.2.1 (2014-10)12Item description column It describes each respective item (e.g. parameters, timers, etc.). Reference column I

36、t gives reference to the specification(s) 1 to 19, except where explicitly stated otherwise. Status column The following notations, defined in ISO/IEC 9646-7 9, are used for the status column: m mandatory - the capability is required to be supported. n/a not applicable - in the given context, it is

37、impossible to use the capability. No answer in the support column is required. o optional - the capability may be supported or not. o.i qualified optional - for mutually exclusive or selectable options from a set. “i“ is an integer which identifies a unique group of related optional items and the lo

38、gic of their selection which is defined immediately following the table. ci conditional - the requirement on the capability (“m“, “o“ or “n/a“) depends on the support of other optional or conditional items. “i“ is an integer identifying a unique conditional status expression that is defined immediat

39、ely following the table. For nested conditional expressions, the syntax “IF . THEN (IF . THEN . ELSE.) ELSE .“ shall be used to avoid ambiguities. If an ELSE clause is omitted, “ELSE n/a“ shall be implied. NOTE: Support of a capability means that the capability is implemented in conformance to the s

40、pecification(s) 1 to 19. Support column The support column shall be filled in by the supplier of the implementation. The following common notations, defined in ISO/IEC 9646-7 9, are used for the support column: Y or y supported by the implementation. N or n not supported by the implementation. N/A o

41、r n/a or “no answer required“ (allowed only if the status is N/A, directly or after evaluation of a conditional status). Values allowed column This column contains the values or the ranges of values allowed. Values supported column The support column shall be filled in by the supplier of the impleme

42、ntation. In this column the values or the ranges of values supported by the implementation shall be indicated. References to items For each possible item answer (answer in the support column) within the PICS proforma, a unique reference exists. It is defined as the table identifier, followed by a sl

43、ash character “/“, followed by the item number in the table. If there is more than one support column in a table, the columns shall be discriminated by letters (a, b, etc.) respectively. EXAMPLE: 5/4 is the reference to the answer of item 4 in table 5. ETSI ETSI TS 102 709-1 V3.2.1 (2014-10)135.2 Id

44、entification of the implementation Identification of the Implementation Under Test (IUT) and the system in which it resides - the System Under Test (SUT) should be filled in so as to provide as much detail as possible regarding version numbers and configuration options. The product supplier informat

45、ion and client information should both be filled in if they are different. A person who can answer queries regarding information supplied in the ICS should be named as the contact person. 5.2.1 Date of the statement Date of the statement: 5.2.2 Implementation Under Test (IUT) identification IUT name

46、: IUT version: 5.2.3 System Under Test (SUT) identification SUT name: Hardware configuration: Operating system: 5.2.4 Product supplier Name: Address:Telephone number: Facsimile number: Additional information: 5.2.5 Client Name: Address:Telephone number: Facsimile number: Additional information: 5.2.

47、6 PICS contact person Name: Telephone number: Facsimile number: Additional information: ETSI ETSI TS 102 709-1 V3.2.1 (2014-10)145.3 PICS proforma tables 5.3.1 Global statement of conformance (Yes/No) Are all mandatory capabilities implemented? NOTE: Answering “No“ to this question indicates non-con

48、formance to the reference protocol specification. Non-supported mandatory capabilities are to be identified in the PICS, with an explanation of why the implementation is non-conforming. 5.3.2 Roles Table 1: Roles Item Is the implementation . Reference Status Support 1 Profile A? ITU-T TRQ.2815 17 o.

49、11 2 Profile B? ITU-T TRQ.2815 17 o.11 3 Profile C? ITU-T TRQ.2815 17 o.11 4 connected with a BICC Network? Rec. ITU-T Q.1902.2 2 o.12 5 connected with an ISUP Network? Rec. ITU-T Q.764 1 o.12 6 connected with a -law network? Clauses 6.1 and 7.1 of ITU-T TRQ.2815 17 o 7 an outgoing international exchange? Rec. ITU-T Q.764 1 o 8 an incoming international exchange? Rec. ITU-T Q.764 1 o 9 Void NOTE: o.11: It is mandatory to support at least one of these items. o.12: It is mandatory to support one of these items. 5.3.3 Connection types