ETSI TS 102 486-2-3-2006 Electromagnetic compatibility and Radio spectrum Matters (ERM) Road Transport and Traffic Telematics (RTTT) Test specifications for Dedicated Short Range Cr.pdf

《ETSI TS 102 486-2-3-2006 Electromagnetic compatibility and Radio spectrum Matters (ERM) Road Transport and Traffic Telematics (RTTT) Test specifications for Dedicated Short Range Cr.pdf》由会员分享，可在线阅读，更多相关《ETSI TS 102 486-2-3-2006 Electromagnetic compatibility and Radio spectrum Matters (ERM) Road Transport and Traffic Telematics (RTTT) Test specifications for Dedicated Short Range Cr.pdf（37页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TS 102 486-2-3 V1.1.1 (2006-08)Technical Specification Electromagnetic compatibilityand Radio spectrum Matters (ERM);Road Transport and Traffic Telematics (RTTT);Test specifications for Dedicated Short Range Communication (DSRC) transmission equipment;Part 2: DSRC application layer;Sub-Part 3:

2、 Abstract Test Suite (ATS) and partial PIXIT proformafloppy3 ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 2 Reference DTS/ERM-TG37-002-3 Keywords DSRC, testing, ATS, TTCN, PIXIT, protocol ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16

3、Siret N 348 623 562 00017 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice Individual copies of the present document can be downloaded from: http:/www.etsi.org The present document may be made available in more than one electronic versio

4、n or in print. In any case of existing or perceived difference in contents between such versions, the reference version is the Portable Document Format (PDF). In case of dispute, the reference shall be the printing on ETSI printers of the PDF version kept on a specific network drive within ETSI Secr

5、etariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/status.asp If you find errors in the present document, please se

6、nd your comment to one of the following services: http:/portal.etsi.org/chaircor/ETSI_support.asp Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications

7、Standards Institute 2006. All rights reserved. DECTTM, PLUGTESTSTM and UMTSTM are Trade Marks of ETSI registered for the benefit of its Members. TIPHONTMand the TIPHON logo are Trade Marks currently being registered by ETSI for the benefit of its Members. 3GPPTM is a Trade Mark of ETSI registered fo

8、r the benefit of its Members and of the 3GPP Organizational Partners. ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 3 Contents Intellectual Property Rights6 Foreword.6 1 Scope 7 2 References 7 3 Definitions and abbreviations.8 3.1 Definitions8 3.2 Abbreviations .8 4 Abstract Test Method (ATM).9 4.1 Test

9、 architecture .9 5 Untestable Test Purposes (TP) .9 6 ATS conventions9 6.1 Naming conventions.10 6.1.1 Declarations part.10 6.1.1.1 General10 6.1.1.2 Test suite operations10 6.1.1.3 Test suite parameter declarations 10 6.1.1.4 Test case selection expression definition 10 6.1.1.5 Test suite constant

10、declarations.10 6.1.1.6 Test suite variable declarations .10 6.1.1.7 Test case variable declarations10 6.1.1.8 Timer declarations.11 6.1.1.9 ASP type definitions .11 6.1.1.10 PDU type definitions.11 6.1.1.11 Co-ordination Message (CM) type definitions11 6.1.1.12 Alias definitions 11 6.1.2 Constraint

11、s part.11 6.1.2.1 General11 6.1.3 Dynamic part 11 6.1.3.1 General11 6.1.3.2 Test Case (TC) identifier.11 6.1.3.3 Test step identifier.12 6.1.3.4 Default identifier .12 6.2 Implementation conventions 12 6.2.1 Declaration part 12 6.2.2 Constraint part 12 6.2.3 Dynamic part 12 Annex A (normative): Abst

12、ract Test Suite (ATS) for Application OBU 13 A.1 The TTCN Graphical form (TTCN.GR) 13 A.2 The TTCN Machine Processable form (TTCN.MP)13 Annex B (normative): Abstract Test Suite (ATS) for Application RSU .14 B.1 The TTCN Graphical form (TTCN.GR) 14 B.2 The TTCN Machine Processable form (TTCN.MP)14 An

13、nex C (normative): Partial PIXIT proforma for Application OBU .15 C.1 Identification summary.15 C.2 ATS summary 15 C.3 Test laboratory15 ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 4 C.4 Client identification15 C.5 SUT 16 C.6 Protocol layer information16 C.6.1 Protocol identification 16 C.6.2 IUT info

14、rmation .16 Annex D (normative): Partial PIXIT proforma for Application RSU 21 D.1 Identification summary.21 D.2 ATS summary 21 D.3 Test laboratory21 D.4 Client identification21 D.5 SUT 22 D.6 Protocol layer information22 D.6.1 Protocol identification 22 D.6.2 IUT information .22 Annex E (normative)

15、: PCTR Proforma for Application OBU 24 E.1 Identification summary.24 E.1.1 Protocol conformance test report24 E.1.2 IUT identification.24 E.1.3 Testing environment.24 E.1.4 Limits and reservation25 E.1.5 Comments.25 E.2 IUT Conformance status 25 E.3 Static conformance summary .25 E.4 Dynamic conform

16、ance summary25 E.5 Static conformance review report.26 E.6 Test campaign report26 E.7 Observations.27 Annex F (normative): PCTR Proforma for Application RSU.28 F.1 Identification summary.28 F.1.1 Protocol conformance test report28 F.1.2 IUT identification.28 F.1.3 Testing environment.28 F.1.4 Limits

17、 and reservation29 F.1.5 Comments.29 F.2 IUT Conformance status 29 F.3 Static conformance summary .29 F.4 Dynamic conformance summary30 F.5 Static conformance review report.30 F.6 Test campaign report30 F.7 Observations.31 Annex G (normative): Profile requirements for Application OBU .32 G.1 Generic

18、 test cases .32 G.2 Specific test cases.32 ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 5 G.3 Non relevant test cases .32 G.4 Modified test campaign report .33 G.5 Observations.33 Annex H (normative): Profile requirements for Application RSU34 H.1 Generic test cases .34 H.2 Specific test cases.34 H.3 N

19、on relevant test cases .34 H.4 Modified test campaign report .34 H.5 Observations.35 Annex I (informative): Bibliography.36 History 37 ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 6 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ET

20、SI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is availa

21、ble from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/webapp.etsi.org/IPR/home.asp). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced

22、 in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Foreword This Technical Specification (TS) has been produced by ETSI Technical Committee Electromagnetic compatibility and Radio spectrum Matters (ERM). The present doc

23、ument is part 2, sub-part 3 of a multi-part deliverable covering Road Transport and Traffic Telematics (RTTT); Test specifications for Dedicated Short Range Communication (DSRC); transmission equipment, as identified below: Part 1: “DSRC data link layer: medium access and logical link control“; Part

24、 2: “DSRC application layer“: Sub-part 1: “Protocol Implementation Conformance Statement (PICS) proforma specification“; Sub-part 2: “Test Suite Structure and Test Purposes (TSS Sub-part 3: “Abstract Test Suite (ATS) and partial PIXIT proforma“. ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 7 1 Scope Th

25、e present document contains the Abstract Test Suite (ATS) and partial PIXIT proforma to test the ERM/TG37 Dedicated Short Range Communication (DSRC); Application layer. The objective of the present document is to provide a basis for conformance tests for DSRC equipment giving a high probability of i

26、nter-operability between different manufacturers equipment. The ISO standard for the methodology of conformance testing (ISO/IEC 9646-1 6, ISO/IEC 9646-2 7 and ISO/IEC 9646-3 8) as well as the ETSI rules for conformance testing (ETS 300 406 5) are used as a basis for the test methodology. 2 Referenc

27、es The following documents contain provisions which, through reference in this text, constitute provisions of the present document. References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For a specific reference, subsequent revisio

28、ns do not apply. For a non-specific reference, the latest version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. 1 CEN EN 12834 (2003): “Road transport and traffic telematics - Dedicated Short Ran

29、ge Communication (DSRC) - DSRC application layer“. 2 CEN EN 12795 (2003): “Road transport and traffic telematics - Dedicated Short Range Communication (DSRC) - DSRC data link layer: medium access and logical link control“. 3 CEN EN 12253 (2003): “Road transport and traffic telematics - Dedicated sho

30、rt-range communication - Physical layer using microwave at 5,8 GHz“. 4 CEN EN 13372 (2003): “Road transport and traffic telematics (RTTT) - Dedicated short-range communication - Profiles for RTTT“. 5 ETSI ETS 300 406: “Methods for Testing and Specification (MTS); Protocol and profile conformance tes

31、ting specifications; Standardization methodology“. 6 ISO/IEC 9646-1: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 1: General concepts“. 7 ISO/IEC 9646-2: “Information technology - Open Systems Interconnection - Conformance testing meth

32、odology and framework - Part 2: Abstract Test Suite Specification“. 8 ISO/IEC 9646-3: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 3: The Tree and Tabular Combined Notation (TTCN)“. 9 ISO/IEC 9646-6: “Information technology - Open Syst

33、ems Interconnection - Conformance testing methodology and framework - Part 6: Protocol Profile Test Specification“. 10 ISO/IEC 9646-7: “Information technology - Open Systems Interconnection - Conformance testing methodology and framework - Part 7: Implementation Conformance statement“. 11 ISO 14906:

34、2004: “Road transport and traffic telematics - Electronic fee collection - Application interface definition for dedicated short-range communication“. ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 8 3 Definitions and abbreviations 3.1 Definitions For the purposes of the present document, the terms and de

35、finitions given in ISO/IEC 9646-7 10, EN 12253 3, EN 12834 1 and EN 13372 4 apply. 3.2 Abbreviations For the purposes of the present document, the abbreviations given in ISO/IEC 9646-1 6, ISO/IEC 9646-6 9, ISO/IEC 9646-7 10, EN 12834 1 and the following apply: ASP Abstract Service Primitive ATM Abst

36、ract Test Method ATS Abstract Test Suite BI Invalid Behaviour tests BST Beacon Service Table BV Valid Behaviour tests CM Co-ordination Message CP Co-ordination Point DSRC Dedicated Short Range Communication EFC Electronic Fee Collection IUT Implementation Under Test LID Link IDentifier LLC Logical L

37、ink Control MAC Medium Access Control OBU On Board Unit PDU Protocol Data Unit PICS Protocol Implementation Conformance Statement RSU Road Side Unit SAP Service Access Point SUT System Under Test TP Test Purpose TSS Test Suite Structure TTCN Tree and Tabular Combined Notation UT Upper Tester VST Veh

38、icle Service Table ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 9 4 Abstract Test Method (ATM) This clause describes the ATM used to test the DSRC Application layer at the OBU side and at the RSU side. 4.1 Test architecture Tester PHY PHY MAC SUT LLC APPL T-Kernel SAP Test Case MAC LLC Figure 1: Test a

39、rchitecture for DSRC Application layer A single party testing concept is used, which consists of the following abstract testing parts: Tester: A test machine that is running a TTCN engine allowing parallel testing and having a standard DSRC LLC, MAC and Physical layer. SUT: System under test: Can be

40、 RSU or OBU Implementation. Test Case: A standard TTCN test case. APPL: A standard DSRC Application to be tested. LLC: A standard DSRC LLC layer. MAC: A standard DSRC MAC layer. T-Kernel-SAP: A SAP between T-Kernel and B/I-Kernel, i.e. above T-Kernel encoding/decoding function. 5 Untestable Test Pur

41、poses (TP) This clause gives a list of TPs which are not implemented in the Abstract Test Suite due to the chosen Abstract Test Method or other restrictions. Table 1: Untestable TPs Test purpose Reason 6 ATS conventions The ATS conventions are intended to give a better understanding of the ATS but t

42、hey also describe the conventions made for the development of the ATS. These conventions shall be considered during any later maintenance or further development of the ATS. The ATS conventions contain two clauses, the naming conventions and the implementation conventions. The naming conventions desc

43、ribe the structure of the naming of all ATS elements. The implementation conventions describe the functional structure of the ATS. ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 10To define the ATS, the guidelines of the document ETS 300 406 5 was considered. 6.1 Naming conventions 6.1.1 Declarations par

44、t This clause describes the naming conventions chosen for the elements of the ATS declarations part. 6.1.1.1 General The following general rules apply for the names given in the declarations part. Names of ASN.1 types imported from the base standard are preserved. Predefined types (e.g. BITSTRING 8)

45、 are never used in structured type definitions, ASP type definitions or PDU type definitions. Simple types are used instead. All declarations in the test suite are listed in alphabetical order. A different order of listing should be used for only maintenance reasons. 6.1.1.2 Test suite operations Th

46、e test suite operation identifiers are prefixed with “TSO_“. EXAMPLE: TSO_substring. 6.1.1.3 Test suite parameter declarations If the test suite parameter references a Protocol Implementation Conformance Statement (PICS) item, the test suite parameter identifiers are prefixed “TSPC_“. EXAMPLE 1: TPC

47、_extended_rf_carriers. If the test suite parameter references a PIXIT item, the suite parameter identifiers are prefixed “TSPX_“. EXAMPLE 2: TSP_pmid. If the test suite parameter represents a system parameter, the complete name defined in the protocol is used. 6.1.1.4 Test case selection expression

48、definition The test case selection expression identifiers begin with the prefix “SEL_“. 6.1.1.5 Test suite constant declarations The test suite constant identifiers are prefixed “TSC_“. If the test suite constant represents a system parameter, the complete name defined in the protocol is used. 6.1.1

49、.6 Test suite variable declarations The test suite variable identifiers are prefixed “TSV_“. Complete names as defined in the protocol are used. 6.1.1.7 Test case variable declarations The test case variable identifiers are prefixed “TCV_“. Complete names as defined in the protocol are used. ETSI ETSI TS 102 486-2-3 V1.1.1 (2006-08) 116.1.1.8 Timer declarations Timers begin with the prefix “T_“. 6.1.1.9 ASP type definitions The general conventions in clause 6.1.1.1 apply. All capital letters shall be used. The identifier