ETSI TR 137 902-2016 Universal Mobile Telecommunications System (UMTS) LTE Measurements of User Equipment (UE) radio performances for LTE UMTS terminals Total Radiated Power (TRP) .pdf

《ETSI TR 137 902-2016 Universal Mobile Telecommunications System (UMTS) LTE Measurements of User Equipment (UE) radio performances for LTE UMTS terminals Total Radiated Power (TRP) .pdf》由会员分享，可在线阅读，更多相关《ETSI TR 137 902-2016 Universal Mobile Telecommunications System (UMTS) LTE Measurements of User Equipment (UE) radio performances for LTE UMTS terminals Total Radiated Power (TRP) .pdf（26页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI TR 1Universal Mobile TelMeasuremenradio performanTotal RadTotal Radiated Se(3GPP TR 37.9TECHNICAL REPORT 137 902 V13.0.0 (2016elecommunications System (LTE; ents of User Equipment (UE) a ces for LTE/UMTS terminaladiated Power (TRP) and Sensitivity (TRS) test methodo.902 version 13.0.0 Release

2、1316-01) (UMTS); als; dology 13) ETSI ETSI TR 137 902 V13.0.0 (2016-01)13GPP TR 37.902 version 13.0.0 Release 13Reference RTR/TSGR-0437902vd00 Keywords LTE,UMTS ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 0001

3、7 - NAF 742 C Association but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any ele

4、ctronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (P

5、DF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at http:/portal.etsi.org/tb/status/sta

6、tus.asp If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photoco

7、pying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. European Telecommunications Standards Institute 201

8、6. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTMand the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM and the GSM logo are Trade Marks regis

9、tered and owned by the GSM Association. ETSI ETSI TR 137 902 V13.0.0 (2016-01)23GPP TR 37.902 version 13.0.0 Release 13Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if a

10、ny, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available

11、on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web server) which are, or

12、may be, or may become, essential to the present document. Foreword This Technical Report (TR) has been produced by ETSI 3rd Generation Partnership Project (3GPP). The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or GSM identities. The

13、se should be interpreted as being references to the corresponding ETSI deliverables. The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under http:/webapp.etsi.org/key/queryform.asp. Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not

14、“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. ETSI ETSI TR 137 9

15、02 V13.0.0 (2016-01)33GPP TR 37.902 version 13.0.0 Release 13Contents Intellectual Property Rights 2g3Foreword . 2g3Modal verbs terminology 2g3Foreword . 4g3Introduction 4g31 Scope 5g32 References 5g33 Definitions, symbols and abbreviations . 5g33.1 Definitions 5g33.2 Symbols 5g33.3 Abbreviations .

16、6g34 General . 6g34.1 Scope 7g34.2 Device Under Test definition . 8g35 Measurement environment condition . 8g35.1 Chamber environment constraints 8g35.2 Positioning Requirements and Coordinate system . 8g35.3 DUT Test Positions and Phantom Specifications . 8g35.3.1 Phantom Specifications . 8g35.3.2

17、DUT Test Positions . 8g36 Measurement parameters 8g36.1 Definition of the Total Radiated Power 8g36.2 Definition of Total Radiated Sensitivity . 9g36.2.1 Total Radiated Sensitivity . 9g36.2.2 Alternate measurement parameter 9g36.3 Sampling grid and independent samples 9g36.4 Measurement frequencies

18、. 9g37 Measurement procedure transmitter performance . 15g37.1 General measurement arrangements . 16g37.2 Procedure for radiated power measurement . 16g37.3 Calibration measurement 17g38 Measurement procedure receiver performance . 17g38.1 General measurement arrangements . 17g38.2 Procedure for rad

19、iated sensitivity measurement . 17g38.3 Calibration measurement 18g3Annex A: System Parameters 19g3A.1 Definition and applicability 19g3A.2 Establishing the connection 19g3A.3 Uplink RB allocation for reference sensitivity . 19g3Annex B: Measurement Uncertainty 21g3Annex C: Anechoic chamber specific

20、ations and validation method 22g3Annex D: Reverberation chamber specifications and validation method . 23g3Annex E: Change history 24g3History 25 ETSI ETSI TR 137 902 V13.0.0 (2016-01)43GPP TR 37.902 version 13.0.0 Release 13Foreword This Technical Report has been produced by the 3rdGeneration Partn

21、ership Project (3GPP). The contents of the present document are subject to continuing work within the TSG and may change following formal TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an identifying change of release date and an incr

22、ease in version number as follows: Version x.y.z where: x the first digit: 1 presented to TSG for information; 2 presented to TSG for approval; 3 or greater indicates TSG approved document under change control. y the second digit is incremented for all changes of substance, i.e. technical enhancemen

23、ts, corrections, updates, etc. z the third digit is incremented when editorial only changes have been incorporated in the document. Introduction In this technical report, the needed modifications to measurement parameters for LTE devices will be studied and applicability of the existing measurement

24、procedures, e.g. TRP and TRS will be evaluated for LTE devices with multiple receive antennas TDD-LTE and FDD-LTE terminals (as it is expected that the same issues are applicable independent of RAT). As UMTS devices with multiple receive antennas are still needing test methodology, it is easy to ext

25、end to this study item contribution to UMTS terminals with, due to similar situation and technical issue. UMTS TRP and TRS test methods should also be updated in the same way. ETSI ETSI TR 137 902 V13.0.0 (2016-01)53GPP TR 37.902 version 13.0.0 Release 131 Scope The present document is a Technical R

26、eport of the Study Item for OTA TRP and TRS requirement of LTE terminals, which was approved at TSG RAN #55 2. The report provides the measurement procedure of Over The Air TRP and TRS requirements for LTE terminals. It will make a simple extension to the UE OTA TRP and TRS test methods TS34.1143 fo

27、r LTE UE with multiple receive antennas, without considering all of the aspects associated with spatial channels. The work should utilise the existing environments in TR25.9144. The results of the UE OTA test method with Head and Hand Phantoms study item can be considered later on once finalized. Th

28、e report also provides some future extensions and work items after LTE TRP and TRS methods mature. 2 References The following documents contain provisions which, through reference in this text, constitute provisions of the present document. - References are either specific (identified by date of pub

29、lication, edition number, version number, etc.) or non-specific. - For a specific reference, subsequent revisions do not apply. - For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including a GSM document), a non-specific reference implicitly re

30、fers to the latest version of that document in the same Release as the present document. 1 3GPP TR 21.905: “Vocabulary for 3GPP Specifications“. 2 RP-120412, “New study item proposal: Measurements of radio performances for LTE terminals - conformance testing methodology“. 3 3GPP TS 34.114: “User Equ

31、ipment (UE) / Mobile Station (MS) Over The Air (OTA) antenna performance“. 4 3GPP TR 25.914: “Measurements of radio performances for UMTS terminals in speech mode“. 5 3GPP TS 36.101: “Evolved Universal Terrestrial Radio Access (E-UTRA) User Equipment (UE) radio transmission and reception“. 6 3GPP TS

32、 36.521-1: “Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) conformance specification; Radio transmission and reception; Part 1: conformance testing“. 7 RP-120368, “Verification of radiated multi-antenna reception performance of UEs in LTE/UMTS WID“. 3 Definitions, symbols a

33、nd abbreviations 3.1 Definitions Void 3.2 Symbols For the purposes of the present document, the following symbols apply: Zenith angle in the spherical co-ordinate system Azimuth angle in the spherical co-ordinate system Solid angle defined at the phase centre of the DUT ETSI ETSI TR 137 902 V13.0.0

34、(2016-01)63GPP TR 37.902 version 13.0.0 Release 13G(,f) Antenna gain pattern in the -polarization as function of the spherical co-ordinates and the carrier frequency F Carrier frequency Ptr Transmitted power Q(,f) Angular power distribution in the -polarization as function of the spherical co-ordina

35、tes and the carrier frequency dB decibel dBm dB referenced to one milliwatt m meter mm millimetre kbps kilobit per second ms millisecond MHz megahertz3.3 Abbreviations For the purposes of the present document, the abbreviations given in TR 21.905 1 and the following apply. An abbreviation defined in

36、 the present document takes precedence over the definition of the same abbreviation, if any, in TR 21.905 1. 3G 3rd Generation 3GPP 3G Partnership Project 3-D Three Dimensional16QAM 16 Quadrature Amplitude Modulation A-MPR Additional Maximum Power Reduction BS Base Station CN Core Network DL Downlin

37、kDUT Device Under Test ETSI European Telecommunications Standards Institute E-UTRA Evolved Universal Terrestrial Radio Access LME Laptop Mounted Equipment LEE Laptop Embedded Equipment LTE Long Term Evolution MPR Maximum Power Reduction MS Mobile Station NB Node BQoS Quality of Service QPSK Quadratu

38、re Phase Shift Keying (modulation) RAB Radio Access Bearer RAN Radio Access Network RB Resource Block RF Radio Frequency Rx Receiver RBstart RB number where a RB allocation begins within the channel SAM Specific Anthropomorphic MannequinTx Transmitter TRP Total Radiated Power TRS Total Radiated Sens

39、itivity (also: Total Isotropic Sensitivity) UL Uplink UE User Equipment UTRA Universal Terrestrial Radio Access 4 General The present document is a Technical Report of the Study Item for OTA TRP and TRS requirement of LTE terminals, which was approved at TSG RAN #55 2. The report provides the measur

40、ement procedure of Over The Air TRP and TRS requirements for LTE terminals. It will make a simple extension to the UE OTA TRP and TRS test methods TR 25.9144 for LTE UE with multiple receive antennas, without considering all of the aspects associated with spatial channels. The work should utilise th

41、e existing environments in TR 25.9144. The results of the UE OTA test method ETSI ETSI TR 137 902 V13.0.0 (2016-01)73GPP TR 37.902 version 13.0.0 Release 13with Head and Hand Phantoms study item can be considered later on once finalized. The report also provides some future extensions and work items

42、 after LTE TRP and TRS methods mature. 4.1 Scope The measurement procedure explained in this document applies to all LTE devices, which are already satisfied the standard 3GPP LTE RF minimum performance requirements and conformance testing defined in 3GPP TS 36.101: Evolved Universal Terrestrial Rad

43、io Access (E-UTRA); User Equipment (UE) radio transmission and reception5 and 3GPP TS 36.521-1: Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE) conformance specification; Radio transmission and reception; Part 1: conformance testing6, respectively. The testing methodology ap

44、plies to any 4G LTE handset, USB-dongle and LEE etc, with internal or external antenna. 3GPP TR 25.9144 has done many meaningful studies for evaluating antenna performance of UMTS and GSM terminals. In this document, the majority work will be focus on the LTE TRP and TRS test. A simple test methodol

45、ogy for LTE devices without channel emulator will be studied. The radio tests considered here are: 1. The measurement of the radiated output power (TRP) 2. The measurement of the radiated sensitivity (TRS) The test procedure described in this document measures the performance of the transmitter and

46、the receiver, including the antenna and also the effects of the user. The purpose of this document is to serve as a standard test procedure for radio performance testing of 4G LTE mobile terminals. It is the intention that this procedure is going to be used by test houses, network operators, mobile

47、terminal and antenna manufacturers, research institutes etc. The motivation for the development of this document is the lack of standards in this area in 3GPP. During RAN4 #62bis following proposal were agreed. Proposal 1: LTE TRP test method is the same for all LTE UEs independent of release, inclu

48、ding e.g. LTE CA, UL TX Div or UL MIMO capable UEs Proposal 2: LTE TRS test method is the same for all LTE UEs independent of release, including e.g. LTE CA, UL TX Div or UL MIMO capable UEs Proposal 3: In the first phase re-use test environments including phantoms available already in TS34.114 for

49、LTE TPR and TRS purposes as well. Once new methods like hand phantom based test environments are defined for UTRA TRP and TRS, then also LTE TRP and TRS testing should be extended to these additional environments. During RAN4 #63 following proposal were agreed. WF 1: Select one channel bandwidth per band for TRP and TRS tests for LTE FDD and TDD. Default channel bandwidth is 10 MHz but another bandwidth can be considered on case by case basis. WF2: For TRS select the reference measurement channel configuration for LTE FD