ETSI EN 303 316-2017 Broadband Direct Air-to-Ground Communications Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands Beamforming antennas.pdf

《ETSI EN 303 316-2017 Broadband Direct Air-to-Ground Communications Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands Beamforming antennas.pdf》由会员分享，可在线阅读，更多相关《ETSI EN 303 316-2017 Broadband Direct Air-to-Ground Communications Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands Beamforming antennas.pdf（33页珍藏版）》请在麦多课文档分享上搜索。

1、 ETSI EN 303 316 V1.1.1 (2017-10) Broadband Direct Air-to-Ground Communications; Equipment operating in the 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz frequency bands; Beamforming antennas; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU HARMONIS

2、ED EUROPEAN STANDARD ETSI ETSI EN 303 316 V1.1.1 (2017-10) 2 Reference DEN/BRAN-60013 Keywords aeronautical, broadband, mobile, network, radio ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16 Siret N 348 623 562 00017 - NAF 742 C Asso

3、ciation but non lucratif enregistre la Sous-Prfecture de Grasse (06) N 7803/88 Important notice The present document can be downloaded from: http:/www.etsi.org/standards-search The present document may be made available in electronic versions and/or in print. The content of any electronic and/or pri

4、nt versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept o

5、n a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at https:/portal.etsi.org/TB/ETSIDeliverableStatus.aspx

6、If you find errors in the present document, please send your comment to one of the following services: https:/portal.etsi.org/People/CommiteeSupportStaff.aspx Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying an

7、d microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media. ETSI 2017. All rights reserved. DECTTM, PLUGTESTSTM, UMTSTM

8、and the ETSI logo are trademarks of ETSI registered for the benefit of its Members. 3GPPTM and LTE are trademarks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. oneM2M logo is protected for the benefit of its Members. GSM and the GSM logo are trademarks re

9、gistered and owned by the GSM Association. ETSI ETSI EN 303 316 V1.1.1 (2017-10) 3 Contents Intellectual Property Rights 5g3Foreword . 5g3Modal verbs terminology 6g3Executive summary 6g3Introduction 6g31 Scope 7g32 References 7g32.1 Normative references . 7g32.2 Informative references 7g33 Definitio

10、ns, symbols and abbreviations . 8g33.1 Definitions 8g33.2 Symbols 8g33.3 Abbreviations . 8g34 Technical requirements specifications . 9g34.1 General . 9g34.1.1 Environmental profile . 9g34.1.2 General System Characteristics 9g34.1.3 Additional requirement for the Aircraft Station 10g34.2 Conformance

11、 requirements 10g34.2.1 General 10g34.2.2 Transmitter EIRP Spectral Density . 10g34.2.2.1 Definition 10g34.2.2.2 Limits 10g34.2.2.2.1 For operation in the 1 900 MHz to 1 920 MHz frequency band 10g34.2.2.2.2 For operation in the 5 850 MHz to 5 875 MHz frequency band 10g34.2.2.3 Conformance . 12g34.2.

12、3 Designation of Centre Frequency . 12g34.2.4 Out-of-band EIRP Spectral Density 12g34.2.4.1 Definition 12g34.2.4.2 Limits 12g34.2.4.2.1 For operation in the 1 900 MHz to 1 920 MHz frequency band 12g34.2.4.2.2 For operation in the 5 855 MHz to 5 875 MHz frequency band 13g34.2.4.3 Conformance . 13g34.

13、2.5 Spurious emissions . 13g34.2.5.1 Definition 13g34.2.5.2 Limits 13g34.2.5.3 Conformance . 13g34.2.6 Cessation of emissions 13g34.2.6.1 Definition 13g34.2.6.2 Limits 13g34.2.6.3 Conformance . 14g34.2.7 Receiver parameters 14g34.2.7.1 Receiver sensitivity . 14g34.2.7.1.1 Definition. 14g34.2.7.1.2 L

14、imits 14g34.2.7.1.3 Conformance . 14g34.2.7.2 Receiver adjacent channel selectivity 14g34.2.7.2.1 Definition. 14g34.2.7.2.2 Limit 14g34.2.7.2.3 Conformance . 14g34.2.7.3 Detect and Avoid capability 14g34.2.7.3.1 Definition. 14g34.2.7.3.2 Limits 14g3ETSI ETSI EN 303 316 V1.1.1 (2017-10) 4 4.2.7.3.3 C

15、onformance . 15g35 Testing for compliance with technical requirements 15g35.1 Environmental conditions for testing . 15g35.2 Interpretation of the measurement results 15g35.3 Test Methods 16g35.3.1 General considerations 16g35.3.2 EIRP Measurements . 16g35.3.2.1 Common test conditions for radiated p

16、ower measurements 16g35.3.2.2 Transmitter EIRP spectral density . 17g35.3.2.2.1 Ground Station measurement 17g35.3.2.2.2 Aircraft Station measurement 18g35.3.2.3 Out-of-band EIRP spectral density . 20g35.3.2.3.1 Tests required for 1 900 MHz to 1 920 MHz band only 20g35.3.3 Transmitter spurious emiss

17、ions . 23g35.3.3.1 Initial conditions . 23g35.3.3.2 Procedure 23g35.3.3.3 Test requirement . 23g35.3.4 Cessation of emissions 23g35.3.4.1 Minimum operational altitude . 23g35.3.4.1.1 Test conditions 23g35.3.4.1.2 Test method . 23g35.3.4.2 Minimum operational elevation angle . 23g35.3.4.2.1 Test cond

18、itions 23g35.3.4.2.2 Test method . 24g35.3.5 Receiver sensitivity . 24g35.3.5.1 Test conditions 24g35.3.5.2 Test Method 24g35.3.6 Receiver Adjacent channel selectivity 24g35.3.6.1 Test conditions 24g35.3.6.2 Test method . 24g35.3.6.3 Test requirement . 24g35.3.7 Aircraft Station Detect and Avoid cap

19、ability 24g35.3.7.0 Applicability 24g35.3.7.1 Test conditions 24g35.3.7.2 Test method . 25g35.3.7.2.1 Detection level . 25g35.3.7.2.2 Reduced transmit EIRP density . 25g35.3.7.2.3 DAA reaction time 26g35.3.7.2.4 Test requirement 26g3Annex A (informative): Relationship between the present document an

20、d the essential requirements of Directive 2014/53/EU . 27g3Annex B (normative): Test specification 28g3B.1 Normal test environment 28g3B.2 RF Bandwidth 28g3B.3 Test Configurations 28g3B.3.1 Transmitter spurious Emissions . 28g3B.3.2 Receiver ACS . 28g3Annex C (normative): Geographical Data . 30g3C.1

21、 Height above Ground . 30g3Annex D (informative): Bibliography . 31g3Annex E (informative): Change history . 32g3History 33g3ETSI ETSI EN 303 316 V1.1.1 (2017-10) 5 Intellectual Property Rights Essential patents IPRs essential or potentially essential to the present document may have been declared t

22、o ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found in ETSI SR 000 314: “Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in respect of ETSI standards“, which is av

23、ailable from the ETSI Secretariat. Latest updates are available on the ETSI Web server (https:/ipr.etsi.org/). Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in ETSI S

24、R 000 314 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document. Trademarks The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners. ETSI claims no ownership of these except for any wh

25、ich are indicated as being the property of ETSI, and conveys no right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks. Foreword T

26、his Harmonised European Standard (EN) has been produced by ETSI Technical Committee Broadband Radio Access Networks (BRAN). The present document has been prepared under the Commissions standardisation request C(2015) 5376 final i.9 to provide one voluntary means of conforming to the essential requir

27、ements of Directive 2014/53/EU on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC i.5. Once the present document is cited in the Official Journal of the European Union under that Directive, complia

28、nce with the normative clauses of the present document given in table A.1 confers, within the limits of the scope of the present document, a presumption of conformity with the corresponding essential requirements of that Directive, and associated EFTA regulations. The technical requirements in the p

29、resent document reflect, in part, the results of studies undertaken within the CEPT on compatibility between broadband direct air-to-ground systems and other applications operating within, or adjacent to, the frequency bands which are designated for BDA2GC operations. These studies are described in

30、ECC Report 209 i.1 (for the 1 900 MHz to 1 920 MHz band) and ECC Report 210 i.2 (for the 5 855 MHz to 5 875 MHz band). The resulting technical and operational requirements to be applied to BDA2GC systems in the 1 900 MHz to 1 920 MHz band and the 5 855 MHz to 5 875 MHz band are contained within ECC

31、Decision(15)02 i.3 and ECC Decision(15)03 i.4 respectively. National transposition dates Date of adoption of this EN: 3 July 2017 Date of latest announcement of this EN (doa): 31 October 2017 Date of latest publication of new National Standard or endorsement of this EN (dop/e): 30 April 2018 Date of

32、 withdrawal of any conflicting National Standard (dow): 30 April 2019 ETSI ETSI EN 303 316 V1.1.1 (2017-10) 6 Modal verbs terminology In the present document “shall“, “shall not“, “should“, “should not“, “may“, “need not“, “will“, “will not“, “can“ and “cannot“ are to be interpreted as described in

33、clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of provisions). “must“ and “must not“ are NOT allowed in ETSI deliverables except when used in direct citation. Executive summary The present document addresses the Broadband Direct Air to Ground Communications system based on th

34、e System Reference Document ETSI TR 101 599 i.10. ETSI TR 101 599 i.10 was used by the ECC, in conjunction with other contributions, to develop technology neutral ECC Decisions on the allocation of European spectrum in the frequency bands 1 900 MHz to 1 920 MHz and 5 855 MHz to 5 875 MHz. The techni

35、cal requirements in the present document reflect, in part, the results of studies undertaken within the CEPT on compatibility between broadband direct air-to-ground systems and other applications operating within, or adjacent to, the frequency bands that are designated for BDA2GC operations. Introdu

36、ction The present document has been developed in accordance with the guidelines contained in ETSI EG 203 336 i.6. ETSI ETSI EN 303 316 V1.1.1 (2017-10) 7 1 Scope The present document specifies technical characteristics and methods of measurements for radio equipment at the Ground Station and Aircraf

37、t Station for Broadband Direct Air-to-Ground communications systems employing beamforming antennas. These radio equipment types are capable of operating in all or any part of the frequency bands given in table 1. Table 1: Radiocommunications service frequency bands Radiocommunications service freque

38、ncy bands Transmit 1 1 900 MHz to 1 920 MHz Receive 1 1 900 MHz to 1 920 MHz Transmit 2 5 855 MHz to 5 875 MHz Receive 2 5 855 MHz to 5 875 MHz The present document covers the essential requirements of article 3.2 of Directive 2014/53/EU i.5 under the conditions identified in annex A. 2 References 2

39、.1 Normative references References are specific, identified by date of publication and/or edition number or version number. Only the cited version applies. Referenced documents which are not found to be publicly available in the expected location might be found at http:/docbox.etsi.org/Reference. NO

40、TE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are necessary for the application of the present document. 1 NIMA Technical Report TR8350.2 (1984, including amendment 1 of 03 Ja

41、nuary 2000 and amendment 2 of 23 June 2004): “Department of Defense World Geodetic System 1984. Its Definition and Relationships with Local Geodetic Systems“. 2 ETSI EN 302 502 (V2.1.1) (03-2017): “Wireless Access Systems (WAS); 5,8 GHz fixed broadband data transmitting systems; Harmonised Standard

42、covering the essential requirements of article 3.2 of Directive 2014/53/EU“. 2.2 Informative references References are either specific (identified by date of publication and/or edition number or version number) or non-specific. For specific references, only the cited version applies. For non-specifi

43、c references, the latest version of the referenced document (including any amendments) applies. NOTE: While any hyperlinks included in this clause were valid at the time of publication, ETSI cannot guarantee their long term validity. The following referenced documents are not necessary for the appli

44、cation of the present document but they assist the user with regard to a particular subject area. i.1 ECC Report 209: “Compatibility/sharing studies related to Broadband Direct-Air-to-Ground Communications (DA2GC) in the frequency bands 1900-1920 MHz / 2010-2025 MHz and services/applications in the

45、adjacent bands“. ETSI ETSI EN 303 316 V1.1.1 (2017-10) 8 i.2 ECC Report 210: “Compatibility/sharing studies related to Broadband Direct-Air-to-Ground Communications (DA2GC) in the frequency bands 5855-5875 MHz, 2400-2483.5 MHz and 3400 3600 MHz“. i.3 ECC Decision (15)02: “The harmonised use of broad

46、band Direct Air-to-Ground Communications (DA2GC) systems in the frequency band 1900-1920 MHz“. i.4 ECC Decision (15)03: “The harmonised use of broadband Direct Air-to-Ground Communications (DA2GC) systems in the frequency band 5855-5875 MHz“. i.5 Directive 2014/53/EU of the European Parliament and o

47、f the Council of 16 April 2014 on the harmonisation of the laws of the Member States relating to the making available on the market of radio equipment and repealing Directive 1999/5/EC. i.6 ETSI EG 203 336: “Electromagnetic compatibility and Radio spectrum Matters (ERM); Guide for the selection of t

48、echnical parameters for the production of Harmonised Standards covering article 3.1(b) and article 3.2 of Directive 2014/53/EU“. i.7 ETSI TR 100 028 (V1.4.1) (all parts): “Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment chara

49、cteristics“. i.8 ETSI TR 100 028-2 (V1.4.1): “ Electromagnetic compatibility and Radio spectrum Matters (ERM); Uncertainties in the measurement of mobile radio equipment characteristics; Part 2“. i.9 Commission Implementing Decision C(2015) 5376 final of 4.8.2015 on a standardisation request to the European Committee for Electrotechnical Standardisation and to the European Telecommunications Standards Institute as regards radio equipment in support of Directive 2014/53/EU of the European Parliament and of the Council. i.10 ETSI TR