ETSI EN 300 497-6-1999 Digital Enhanced Cordless Telecommunications (DECT) Common Interface (CI) Test Case Library (TCL) Part 6 Test Suite Structure (TSS) and Test Purposes (TP) - .pdf

《ETSI EN 300 497-6-1999 Digital Enhanced Cordless Telecommunications (DECT) Common Interface (CI) Test Case Library (TCL) Part 6 Test Suite Structure (TSS) and Test Purposes (TP) - .pdf》由会员分享，可在线阅读，更多相关《ETSI EN 300 497-6-1999 Digital Enhanced Cordless Telecommunications (DECT) Common Interface (CI) Test Case Library (TCL) Part 6 Test Suite Structure (TSS) and Test Purposes (TP) - .pdf（39页珍藏版）》请在麦多课文档分享上搜索。

1、, STD*ETSI EN 300 497-b-ENGL L77 I 3400855 0445822 582 D ETSI EN 300 497-6 V0.3.2 (1999-09) European Standard (Telecommunications series) Digital Enhanced Cordless Telecommunications (DECT); Common Interface (Ci); Test Case Library (TCL); Part 6: Test Suite Structure (TSS) and Test Purposes (TP) - N

2、etwork (NWK) layer - Portable radio Termination (PT) STDaETSI EN 300 497-b-ENGL 1999 m 3400655 0445823 419 m ETSI EN 300 497-6 V0.3.2 (1999-09) 2 Reference RENIDECT-040131-6 (4lpiOll.PDF) Keywords DECT, temiinal, testing, TSSaTP, network ETSI Postal address F-O6921 Sophia Antipolis Cedex - FRANCE Of

3、fice address 650 Route des Lucioles - Sophia Antipolis Valbonne - FRANCE Siret No 348 623 562 O0017 - NAF 742 C Association but non lucrati enregistre b Sous-Prfecture de Grasse (06) No 7803188 Tel.: +33 4 92 94 42 O0 Fax: +33 4 93 65 47 16 Internet secretariatetsi.fr Individual copies of this ETSI

4、deliverable can be downloaded from http:/www.etsi.org If you find errors in the present document, send your comment to: editoretsi.fr Copyright Notification No part may be reproduced except as authorized by written permission. The copyright and the foregoing restriction extend to reproduction in all

5、 media. Q European Telecommunications Standards Institute 1999. All rights reserved. ETSI STD*ETSI EN 300 497-b-ENGL A999 3400855 0445824 355 3 ETSI EN 300 497-6 V0.3.2 (1999-09) Contents Intellectual Property Rights 5 Foreword 5 1 Scope 6 2 References 6 3 Definitions and abbreviations 7 3.1 DECT de

6、finitions . 7 3.2 Abbreviations . 7 4 Test Suite Structure (TSS) . 9 4.1 TSS overview . 9 4.2.1 Protocol groups 10 4.2.1.1 4.2.1.2 Mobility Management (MM) 10 4.2.1.3 Lower layer Management Entity (ME) . 10 4.2.1.4 4.2.1.5 4.2.1.6 4.2.1.7 4.2.2 4.2.2.1 4.2.2.2 4.2.2.3 4.2.2.4 4.2.2.5 4.2.2.6 5 4.2 T

7、est groups . 10 Call Control (CC) . 10 Link Control (LC) . 10 Call Independent Supplementary Services (CISS) 10 Connection Oriented Message Services (COMS) . 10 Basic InTerconnection tests (IT) 10 Capability tests (CA) 10 Connectionless Message Services (CLMS) 10 Main test groups . 10 Valid Behaviou

8、r tests (BV) 10 Invalid Behaviour tests (BI) 11 InOpportune Behaviour tests (BO) . 11 TImer expiry and counter mismatch tests (TI) 11 Test Purposes (TPs) . 11 5.1 5.1.1 5.1.2 5.1.3 5.2 5.2.1 5.2.2 5.2.3 5.2.3.1 5.2.3.2 5.2.3.3 5.2.3.4 5.2.3.5 5.2.3.6 5.2.3.7 5.2.3.8 5.2.4 5.2.5 5.2.6 5.3 5.3.1 5.3.2

9、 5.3.3 5.3.3.1 5.3.3.2 5.3.3.3 5.3.3.4 Introduction 11 TP definition conventions 11 References 11 TP naming conventions 12 CC test purposes 12 CCOT test purposes 13 CC/CA test purposes 13 CCIBV test purposes 13 CC/BV/OC test purposes 14 CCIBVOC test purposes . 15 CC/BV/CI test purposes . 16 CC/BV/CR

10、 test purposes 18 CC/BV/SC test purposes . 18 CC/BV/PM test purposes 18 CC/BV/RS test purposes . 19 CCIBVMP test purposes 19 CCIBO test purposes 22 CCIBI test purposes 22 CC/TI test purposes 23 MM test purposes . 23 MMAT test purposes 23 MM/CA test purposes 23 MIWBV test purposes 24 MMIBVAD test pur

11、poses . 24 MM/BV/AU test purposes 25 MMIBVILO test purposes 26 MM/BV/AR test purposes 28 ETSI STD ETSI 5.3.3.5 5.3.3.6 5.3.3.7 5.3.4 5.3.5 5.3.6 5.4 5.4.1 5.4.2 5.5 5.5.1 5.5.1.1 5.5.1.2 5.5.1.3 5.5.1.4 5.5.2 5.5.3 5.6 5.6A 5.7 5.8 5.9 EN 300 497-b-ENGL 1999 m 4 3400855 0445825 291 ETSI EN 300 497-6

12、 V0.3.2 (1999-09) MMIBVIKA test purposes 29 MM/BV/CH test purposes 30 MM/BV/PR test purposes . 29 MM/BO test purposes 31 MM/BI test purposes 31 MEBV test purposes . 32 MM/TI test purposes 32 ME test purposes 32 MEDO test purposes . 33 LC test purposes . 34 LCBV test purposes 34 LC/BV/LE test purpose

13、s . 34 LC/BV/LR test purposes . 34 LCBVLS test purposes . 35 LCBVLL test purposes . 35 LC/BI test purposes 35 LCITI test purposes 36 IS test purposes 36 ISBV test purposes . 36 CL test purposes . 37 CLEW test purposes 37 MO test purposes . 37 Bibliography . 38 History 39 ETSI STDeETSI EN 300 497-h-E

14、NGL 1999 9 31100855 041i582h 128 = ETSI EN 300 497-6 V0.3.2 (1999-09) 5 Intellectual Property Rights IPRs essential or potentially essential to the present document may have been declared to ETSI. The information pertaining to these essential IPRs, if any, is publicly available for ETSI members and

15、non-members, and can be found in SR O00 3 14: %tellectual Property Rights (TPRs): Essential, orpotentially Essential, IPRs notifzed to ETSI in respect of ETSI standards“, which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web server (http:/www.etsi.orgipr). Pursua

16、nt to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee can be given as to the existence of other IPRs not referenced in SR O00 3 14 (or the updates on the ETSI Web server) which are, or may be, or may become, essential to the present document.

17、 Foreword This European Standard (Telecommunications series) has been produced by ETSI Project Digital Enhanced Cordless Telecommunications (DECT). The present document is part 6 of a multi-part EN covering the Common Interface (CI) Test Case Library (TCL), as identified below: Part 1: Part 2: Part

18、3: Part 4: Part 5: Part 6: “Test Suite Structure (TSS) and Test Purposes (TP) for Medium Access Control (MAC) layer“; “Abstract Test Suite (ATS) for Medium Access Control (MAC) layer - Portable radio Termination (PT)“; “Abstract Test Suite (ATS) for Medium Access Control (MAC) layer - Fixed radio Te

19、rmination (IT)“; “Test Suite Structure (TSS) and Test Purposes (TP) - Data Link Control (DLC) layer“; “Abstract Test Suite (ATS) - Data Link Control (DLC) layer“; “Test Suite Structure (TSS) and Test Purposes (TP) - Network Termination (PT)“; “Abstract Test Suite (ATS) for Network (NWK) layer - Port

20、able radio Termination (PT)“; “Test Suite Structure (TSS) and Test Purposes (TP) - Network (NWK) layer - Fixed radio Termination (FT)“; “Abstract Test Suite (ATS) for Network (NWK) layer - Fixed radio Termination (FT)“. layer - Portable radio Part 7: Part 8: Part 9: National transposition dates Date

21、 of adoption of this EN: Date of latest announcement of this EN (doa): Date of latest publication of new National Standard or endorsement of this EN (dop/e): Date of withdrawal of any conflicting National Standard (dow): 27 August 1999 30 November 1999 3 1 May 2000 3 1 May 2000 STDeETSI EN 300 477-b

22、-ENGL 1997 m 3400855 OU45827 Ob4 N 6 ETSI EN 300 497-6 V0.3.2 (1999-09) 1 Scope The present document contains the test specification for the Digital Enhanced Cordless Telecommunications (DECT) (EN 300 175 parts 1 to 8 i to SI). The objective of this test specification is to provide a basis for appro

23、val tests for DECT equipment giving a high probability of air interface inter-operability between different manufacturers DECT equipment. This test specification defines the Test Suite Structure (TSS) and Test Purposes (TP) for testing of the Network (NWK) layer at the Portable radio Termination (PT

24、). The IS0 standard for the methodology of conformance testing (ISOIEC 9646-1 121) as well as the ETSI rules for conformance testing (ETS 300 406 9) are used as a basis for the test methodology. Test specifications for the Physical layer (PHL) are provided in other DECT standards. 2 References The f

25、ollowing documents contain provisions which, through reference in this text, constitute provisions of the present document. 0 References are either specific (identified by date of publication, edition number, version number, etc.) or non-specific. For a specific reference, subsequent revisions do no

26、t apply. For a non-specific reference, the latest version applies. A non-specific reference to an ETS shall also be taken to refer to later versions published as an EN with the same number. il EN 300 175-1 : “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 1 : Overvi

27、ew“. EN 300 175-2: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 2: Physical Layer (PHL)“. EN 300 175-3: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 3: Medium Access Control (MAC) layer“. EN 300 175-4: “Digital Enhanced Cordle

28、ss Telecommunications (DECT); Common Interface (CI); Part 4: Data Link Control (DLC) layer“. EN 300 175-5: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 5: Network (NWK) layer“. EN 300 175-6: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (

29、CI); Part 6: Identities and addressing“. EN 300 175-7: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 7: Security features“. EN 300 175-8: “Digital Enhanced Cordless Telecommunications (DECT); Common Interface (CI); Part 8: Speech coding and transmission“. ETS 300

30、406: “Methods for Testing and Specification (MTS); Protocol and profile conformance testing specifications; Standardization methodology“. EN 300 444: “Digital Enhanced Cordless Telecommunications (DECT); Generic Access Profile (GAP)“. EN 300 824: “Digital Enhanced Cordless Telecommunications (DECT),

31、 Cordless Terminal Mobility (CTM); CTM Access Profile (CAP)“. 21 i31 41 51 61 71 81 91 IO1 Il 11 ETSI 7 ETSI EN 300 497-6 V0.3.2 (1999-09) I21 ISOIIEC 9646- 1 : “Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 1 : General concepts“. ISOIIEC 9

32、646-2: “Information technology; Open Systems Interconnection; Conformance testing methodology and framework; Part 2: Abstract Test Suite Specification“. i31 3 3. I Definitions and abbreviations DECT definitions For the purposes of the present document, the terms and definitions given in ISO/IEC 9646

33、-1 121, ISOIIEC 9646-2 1131, EN 300 175-1 i, EN 300 175-5 5, EN 300 175-6 6 and EN 300 175-7 7 apply. 3.2 Abbreviations For the purposes of the present document, the following abbreviations apply: AC AR AU BI BO BV CA cc CH CI CISS CLMS COMS CR DECT FT HP IC ID IPUI IUT KA LC LE LL LO LR LS ME MM MO

34、 NWK oc PARK PDU PHL PICS Authentication Code Access Rights Authentication Invalid Behaviour Inopportune Behaviour Valid Behaviour Capability Call Control Ciphering Call Information Call Independent Supplementary Services Connectionless Message Services Connection Oriented Message Services Call Rele

35、ase Digital Enhanced Cordless Telecommunications Fixed radio Termination Handover Procedure Incoming Call Identification International Portable User Identity Implementation Under Test Key Allocation Link Control connection oriented Link Establishment connectionless Link control Location connection o

36、riented Link Release connection oriented Link Suspend and resume Management Entity Mobility Management Connection Oriented Message Services Network layer Outgoing Call Portable Access Rights Key Protocol Data Unit Physical layer Protocol Implementation Conformance Statement ETSI STD-ETSI EN 300 497-

37、6-ENGL 3999 8 ETSI EN 300 497-6 V0.3.2 (1999-09) PIXIT PM PR PT RS sc TP TSS UAK Protocol Implementation Extra Information for Testing Packet Mode Parameter Retrieval Portable radio Termination Call Related Supplementary Services Service Change Test Purpose Test Suite Structure User Authentication K

38、ey STD-ETSI EN 300 497-b-ENGL 1999 3400855 0445830 b59 M 9 ETSI EN 300 497-6 V0.3.2 (1999-09) 4 Test Suite Structure (TSS) 4.1 TSS overview PT - - cc IT CA BV BO BI TI -“-FA -oc IC -CI -CR - sc - PM - - RS - HP ID AU LO AR KA PR CH I BO LE LR LS LL BV - IS - MO - CL BV Figure i: TSS ETSI - STD-ETSI,

39、 EN 300 497-b-ENGL 1999 9 3g00855 0445833 595 W 10 ETSI EN 300 497-6 V0.3.2 (1999-09) 4.2 Test groups 4.2.1 Protocol groups 4.2.1 .I Call Control (CC) Reference: EN 300 175-5 5, subclause 5.2, clause 9 and subclause 15.7. 4.2.1.2 Mobility Management (MM) Reference: EN 300 175-5 5, subclause 5.6 and

40、clause 13. 4.2.1.3 Lower layer Management Entity (ME) Reference: EN 300 175-5 5, clause 15. 4.2.1.4 Link Control (LC) Reference: EN 300 175-5 5, subclause 5.7 and clause 14. 4.2.1.5 Call Independent Supplementary Services (CISS) Reference: EN 300 175-5 5, subclauses 5.3 and 10.4.2.2. 4.2.1.6 Connect

41、ion Oriented Message Services (COMS) Reference: EN 300 175-5 5, subclause 5.4 and clause 11. 4.2.1.7 Connectionless Message Services (CLMS) Reference: EN 300 175-5 5, subclause 5.5 and clause 12. 4.2.2 Main test groups 4.2.2.1 Basic InTerconnection tests (IT) IT tests provide limited testing of an I

42、mplementation Under Test (IUT) in order to establish that there is suficient conformance for possible interconnection without trying to perform thorough testing. In particular, only those test cases will be executed which will assure the sufficient interconnection between the IUT of the NWK layer an

43、d the test system exists, so that the rest of the test cases can then be put into execution. 4.2.2.2 Capability tests (CA) CA tests provide limited testing that the observable capabilities of the IUT are in accordance with the static conformance requirements and the additional capabilities claimed i

44、n the Protocol Implementation Conformance Statement / Protocol Implementation Extra Information for Testing (PICS I PIXIT). In particular, this test group can be regarded as a set of spot checks for ail the capabilities of the IUT stated in the PICS / PIXIT. Scope of the test group is the observable

45、 capabilities of the IUT with respect to NWK layer connection, call control, and the mobility management. 4.2.2.3 Valid Behaviour tests (BV) BV group tests an IUT in response to valid behaviour of the test system. “Valid“ means that a test event is syntactically and contextually correct. All test ca

46、ses in the valid behaviour group are intended to verify as thoroughly as possible the various functions of the protocol. ETSI STDeETSI EN 300 497-6-ENGL 1999 = 3400855 0445832 421 m TP Id according to the TP naming conventions TP Id: Reference: Condition: Stimulus: Expected behaviour: 11 ETSI EN 300

47、 497-6 V0.3.2 (1999-09) Reference Initial condition Stimulus Expected behaviour The TP Id is a unique identifier it shall be specified according to the TP naming conventions defined in the subclause below. The reference should contain the references of the subject to be validated by the actual TP (s

48、pecification reference, clause, paragraph). The condition defines in which initial state the IUT has to be to apply the actual TP. The stimulus defines the test event to which the TP is related. Definition of the events that are expected from the IUT to confonn to the base specification. 4.2.2.4 Inv

49、alid Behaviour tests (BI) BI group is intended to veri that the IUT is able to react properly in case an invalid protocol data unit (message) occurring. Invalid Protocol Data Unit (PDU) here means syntactically or semantically invalid test events generated by the test system. A syntactically or semantically invalid test event regardless of the current state is not allowed. 4.2.2.5 InOpportune Behaviour tests (BO) BO test group is intended to verify that the IUT is able to react properly in case an inopportune test even